Press CTRL/F to search this page (no -)

 SAMSUNG EURO SERVICE CENTRE, UNIT A,STAFFORD PARK 12 TELFORD,
 SHROPSHIRE TF3 3BJ 01952 207 171 FAX 01952 293 459.
'SKY REMOTE CODES SAMSUNG 0060 065, 584, 037, 245, 476, 398, 516, 292, 318, 037
151MP NO RF PIC, PC OK, HELP ???
151MP NO RF PIC, PC OK, TUNER BOX(TN-RBA10/RBAS-T)
20A5 FIELD COLLAPSE IC301(TDA8350Q) 10UF 100UF63V 10R,5W
20A5 FIELD CRAMP IC301(TDA8350Q) (10UF 100UF63V) 10R,5W CERAMIC
20A5 PART FIELD COLLAPSE IC301 (TDA8350Q) 10UF 100UF, 63V) 10R,5W CERAMIC RESISTOR ACROSS PINS 3/5
26LCD- NO DIGI CHANNELS OR DIGI MENU.IN STBY.PRESS INFO,MENU,MUTE.STBY.
26LCD NO DIGI LOCATE OPTION 12 THEN RIGHT ARROW-SWITCH OFF-THEN RE-INSTALL
28W8VDE KS3AP NO BLUE,TDA6101Q R513(100K)
5" TV/RADIO BUZZ SND ADJUST QUADRATURE COIL L301
5" TV/RADIO EXCESS BRILL/NO SND, IC202
5" TV/RADIO FIELD COLLAPSE R519(10K)
5" TV/RADIO NO SND IC301,R307(22R),C317(470UF)
5" TV/RADIO NO TUNING,R206(10K)
5" TV/RADIO POOR CONTRAST CRT FAUK=LT
5" TV/RADIO POOR FOCUS CRT
5" TV/RADIO RADIO DEAD C104(100UF)
5" TV/RADIO DEAD DC POWER SOCKET
5" TV/RADIO DEAD Q702,Q703,D702
5" TV/RADIO EXCESS WIDTH,Q701(TIP42C)
5" TV/RADIO SNOWY PIC Q201 OR TUNER UNIT
940MW [R] S LS19DOCSS/EDC
BT110 ALBA PTC9C GOODMANS Q9001
BT110 ALBA PTC9C GOODMANS Q9001
BT110 NO TUNING R128 6K8 FEED RES TO 33V REG
BT110 SERVICING THE MODEL BT110 SEE TV MAG AUG 1993
BT110/ ALBA PTV9C DEAD , DC POWER SOCKET
BT110/ ALBA PTV9CNO TV TUNING RADIO OK 6K8 R128 FEEDS THE 33V REGULATOR IC102
BT309K 12" BW
BT309K BLANK WHITE RASTER DETECTOR CAN IN IF
BT309K BLANK WHITE RASTER. DETECTOR CAN IN IF STRIP.
BT309K FIELD COLLAPSE R511(33K).
BT309K UWA 12/14" MONO
BT510 GOODMANS Q9001 ALBA PTC9C 5" BW TV/RADIO
BT510 GOODMANS Q9001 ALBA PTC9C 5" MONO WITH RADIO
C11-6229T NO PIC CRT SOCKET HAD ARCED INSIDE
C1212R WON'T START LOPTX.
C1212R WONT START XTAL 4MHZ.
C13312Z NO TUNING 0-30V LINE NOT VARYING 05(10K)OPEN
C13312Z VOLUME STUCK(MAX)OSD DOES R625(10K)OPEN
C1348 Z14 DEAD 1.25AT+270PF2KV ACROSS LOPTR
C15012Z DRIFTS OFF TUNE R116(120K)
C15012Z SEE P58 BELOW
C1537V FAILURE OF Q901 2SC3552 AT SWITCH ON R910 270K
C1537V FIELD ROLL WHEN CHANGING STATIONS C307 0.47MFD,50V TANT
C1537V NO VIS,JUST BLANK RASTER TUNER ,(A DIFFERENT TUNER IS SUPPLIED.)
C1541ZG WHISTLE ON SND RC11 FROM 1UF - 10UF
C15A COMBI NO EJECT MODE SWITCH
C517Z
 CB14F1 SEE S15A
CB14F1 S15A
CB14F12(T)(Z) KS1A
CB14F1T S15A
CB14V10 SEE SCT13B
CB14V10 SCT13B
CB14V20 SEE SCT13B
CB14V20 SCT13B
CB14Y52T KS1A
CB20792T KS1A
CB20F12(T)(Z) KS1A
CB20F42(T)(Z) KS1A
CB20H1 SEE S15A
CB20H1 S15A
CB20H12T KS1A
CB20H32T KS1A
CB20P30 SEE SCT13B
CB20P30 SEE S15A
CB20P30 S15A
CB20P30 SCT13B
CB20S10 SEE SCT13B
CB20S10 SCT13B
CB20S20 SEE S15A
CB20S20 SEE SCT13B
CB20S20 S15A
CB20S20 SCT13B
CB21F12T KS1A
CB21H1 SEE S15A
CB21H1 S15A
CB21H12T KS1A
CB21P30 SEE S15A
CB21P30 SEE SCT13B
CB21P30 S15A
CB21P30 SCT13B
CB21S10 SEE SCT13B
CB21S20 SEE S15A
CB21S20 SEE SCT13B
CB3351A NO SOUND GOOD PIC EUROPE MODEL 6MEG XTALS.
CB336F SND WILL NOT TURN DOWN. R604(1R).
CB3373 SEE S15A
CB3373 SEE SCT13B
CB3373T NO SND. TDA7056B
CB3373T NO SND.R1010(C839) R1012(C814)BC547 WITH EXTERNAL BASE RESISTORS
CB3373T Q907 (KSR1012/BC547+47K IN BASE) Q908 (KSR1010/BC547+10K IN BASE)
CB5012Z
 CB5012Z SEE P58SC BELOW
CB5012Z(P58SC) NO COLOUR, STUCK ON SECAM R514(100K)
CB501FZ1 SCT11D
CB5020 SEE S15A
CB5020 S15A
CB5020 P58SC TUNING NOT STOPPING R116(120K)
CB5020(P58SC) TUNING NOT STOPPING R116(120K)
CB5035Z OSD ,EEPROM, TUNER EARTH WIRE
CB5073 SEE S15A
CB5073 SEE SCT13B
CB5079 SEE S15A
CB5079 SEE SCT13B
CB5320 SEE S15A
CB5373 SEE S15A
CB5373 SEE SCT13B
CB5373 SMR40200 BU508AF HYBRID PANEL HISO169B, 150V AVALANCHE DIODE, 33UF CAP
CB5379 SEE S15A
CB5379 S15A
CB7230WT
 CB7230WT FIELD COLLAPSE ,O/P IC AND ADD EXTRA HEATSINK
CB7230WT FIELD COLLAPSE TDA3654Q
CB7230WT FIELD COLLAPSE TDA3654Q ADD EXTRA COOLING
CB7230WT FIELD COLLAPSE TDA3654Q REDUCE 25V SUPPLY
CB7230WT FIELD COLLAPSE, OP CHIP AND INCREASE HEATSINK
CB7230WT HIGH PITCH FREQUENCY SQUEAL FROM TRANSFORMER
CB7230WT NOISY TRANSFORMER ADD 470PF ACROSS TO ALTER PITCH
CB7230WT POOR POWER 220UF400V IN PSU
CB7230WT PSU FLUTTERS STBY,LO 320V (220UF 400V),
CF14Y52Z KS1A
CF20F42Z KS1A
CF25A64DF BENT VERTICALS/FLYBACK LINES ,FR359(10R)
CF25A64DF DEAD/TRIPPING ,TDA8350Q ,FR359(10R)
CF5344N FIELD COLLAPSE & NO SND 12V DOWN
CI SLOW START/LOW HT 47UF35V PIN9 TDA4601.
CI1212R FAILURE TO START NO START UP VOLTS TO PIN 8 IC105 MICRO. - CHIP , TMP47C433AN3842
CI1213R DEAD - PSU STARTS UP THEN SHUTS DOWN L110 IN HT FEED TO LOP STAGE
CI1213R DEAD L110 PINS.
CI1213R DEAD L110, IN THE HT FEED TO THE LINE OUTPUT STAGE,
CI125 GOODMANS GTV9200 "5"" COL PORTABLE WITH RADIO"
CI125 GOODMANS GTV9200 5" COL PORTABLE WITH RADIO
CI125R GOODMANS GTV9200/CI125R SEE TV MAG DEC 1993
CI1312Z TUNE OSD BAR OK,10K RR05
CI13352 P68
CI1338/514 LOW BRIGHTNESS WITH WASHED OUT PIC R207 120K ½W, R208 127K ½W, C519 330PF 1KV - CAP ON CRT BASE
CI1338/514 SMALL PIC VARIES WITH BRIGHTNESS E CONNECTOR 125V OF Q801 STR3125
CI1338X HIGH PITCHED WHINE WHEN HEATED T402 PIN CORR TRNSFMR
CI1338X WHINING NOISE T402 LOOSE WINDINGS TRY CABLE TIES + GLUE
CI14F1T S15A (MARKED CI14F1T5X NEAR BARCODE) 1999, MANUAL 3S15A-1402
CI14F1TS S15A (MARKED CI14F1TS0X NEAR BARCODE) 2001, MANUAL 3S15A-SA14-01
CI14F1Z S15A (MARKED CI14F1Z5X NEAR BARCODE) 1999, MANUAL 3S15A-1402
CI14F1Z SNOW 150PF CAP FROM MICROPRO
CI14Y2TS KS1A STBY X901(12MHZ)
CI14Y42T KS1A REV.1(MARKED CI14Y42TSX NEAR BARCODE 2002, MANUAL 3KS1A-SIEL-0910
CI14Y42Z KS1A REV.1(MARKED CI14Y42ZSX NEAR BARCODE 2002, MANUAL 3KS1A-SIEL-0910
CI14Y4T INT SND SPKR TERMINAL
CI14Y4T S15A (MARKED CI14Y4T6X NEAR BARCODE) 2001, MANUAL 3S15A-SIEL-2101
CI14Y4Z S15A (MARKED CI14Y4Z6X NEAR BARCODE) 2001, MANUAL 3S15A-SIEL-2101
CI14Y52Z KS1A (MARKED CI14Y52ZBX NEAR BARCODE) 2001, MANUAL 3KS1A-SEH-0917
CI14Y5Z S15A (MARKED CI14Y5ZS5X NEAR BARCODE) 2001, MANUAL 3S15A-SEH-1403
CI14Y5Z S15A (MARKED CI14Y5ZW5X NEAR BARCODE) 2001, MANUAL 3S15A-SEH-1403
CI1533 DEAD WITH WHISTLE CHECK C412 FOR
CI1537 BLANK RASTER TAKES INPUT FROM FRONT SOCKET TUNER U/S
CI1683 INT START,C808(47UF25V)
CI20520BT DEAD C805(2N2F800V)
CI20F12T DEAD LOPTR(2SD2499),LOPTX(AA26-00065A)
CI20F12T KS1A(MARKED CI20F12TSX) 2001, MANUAL 3KS1A-SEH-0917
CI20F12Z KS1A (MARKED CI20F12ZSX) 2001, MANUAL 3KS1A-SEH-0917
CI20F32T(Z) KS1A(P) REV.1 2002, MANUAL AA82-00215A
CI20S10BZ S15A (=CI501FZ5X) 1999, MANUAL 3S15A-1402
CI20S20BT
 CI20S20BT S15A
CI20S20BT S15A (=CI501FT5X) 1998, MANUAL 3S15A-0101
CI20S2OBT DEAD C805(2N2F800V)
CI210
CI210R / NIKKAI BABY 10 5A D.C. POWER JACK, WHICH HAD MELTED.
CI210R GOTO CI210
CI210R BABY 10 BURN UP ROUND BRIDGE RECYS. DC JACK SOCKET .
CI210R BABY 10 DEAD. POTTED REGULATOR.
CI210R BABY10 SEE BABY10
CI210R BLACK & WHITE BARS INT - GOES TO C239 1000µ 25V
CI210R BLANK RASTER/FLYBACK LO 115VN C512(22UF160V).
CI210R BLANK WHITE RASTER C512 22UF, 160V
CI210R BLANK WHITE RASTER WITH FB LINES CRT CATH VOLTS C512 22UF160V IN 115V SUPPLY DRIED UP
CI210R DEAD - 5A FUSE BLOWN. SK103 (DC POWER SOCKET)
CI210R DEAD 5A FUSE SK103 - DC POWER SKT
CI210R INT PICTURE GOES TO B&W BARS & CUTS OUT TO SB C239(1,000UF 25V)
CI210R NIKAI BABY 10 ALBA CTV10 BOOTS CTV1010R
CI210R NIKAI BABY 10 ALBA CTV10 BOOTS CTV1010R
CI210R NO BLUE L107 22UH
CI210R NO SND OR PIC - LED LIT,RELAY CLICKS D106 FR304
CI210R STBY 11V HT LINE RISES TO 2.5V THEN OFF. D106 FR304 EFFICIENCY DIODE IN LOP STAGE
CI210R STBY D106(FR304) S/C.
CI210R STBY LED. FR304 EFFICIENCY DIODE D106, NOT THE LOPTR
CI212
 CI212 MAX SND, Q119 2SC1685
CI212R DEAD IC105 MICRO , - SHOULD HAVE I/P OF 4.5V PIN 42 & 4.7V O/P AT PIN 8
CI212R DEAD TMP47C433AN3842 MICROCHIP IC105
CI212R SND AT MAX & WON'T TURN DOWN Q119 2SC1685 LEAKY
CI212R SND WILL NOT TURN DOWN. Q119(2SC1685)LEAKY.
CI213 10" PORTABLE
CI213R 10" BABY 10.
CI213R DIODE FR340(BY228) FROM LOPTX PIN RHS.
CI213R INT DEAD MAINS BRIDGE RECT INT
CI213R INT DEAD. MAIN BRIDGE RECTIFIER
CI21F12TS KS1A (MARKED CI21F12TSX) 2001, MANUAL 3KS1A-SEH-0917
CI21F32T KS1A(P) REV.1 2002, MANUAL 3KS1A-SEH-1104
CI21S20BT S15A
CI21S20BT S15A INT FIELD HEIGHT,IC201 GOTO S15A
CI28C7D S51A 2001, MANUAL 3S51A-SEH-6201
CI330
 CI330F DEAD - 800MA FUSE BLOWN. R801(POSISTOR)IN DEGAUSE CCT,C805(0.22UF)
CI330F/Z DEAD. MAINS TX PRIMARY - SEE TV MAG.
CI3312 CI5013 HIGH HT ON B1(125V)LINE,CAUSING Q402,R807(11K) IC801 FOR CONTROLAMP
CI3312 CI5013 P58 HIGH HT ON B1(125V)LINE,Q402 R807(11K) IC801 CONTROL AMP
CI3312 DEAD C808 10µ 50V LOW CAP, C817 100µ 25V LOW CAP
CI3312 LOSS OF TUNING MEMORY RIC02 PCD8572
CI3312 NO LUMA FIT INSULATED LINK FROM PIN 20 TO 16)FIT 3 X 47OHM 1/8W RES. WITH RGB I/PS PINS 7, 11,
CI3312 NO SWITCHING CVBS-AV MONITOR VOLTS ON IC201 TEA20 CHECK RQ08 PIN 12 OF RIC01
CI3312 P58S LO HIEGHT R302(470K)
CI3312 P58SC
CI3312 P58SC PORTABLE P58SC
CI3312 TUNING DRIFT CHECK R124 33K, R116/RR26 120K IN AFC CCT - SHOULD BE 2.5V AT PIN 9 OF MICRO RIC01 WHEN AFC LOCKED
CI3312 TUNING DRIFT R124 33K R116,R126 120K
CI3312 TUNING INFO LOST ON CHANNEL PCD8572 RIC02 US
CI3312Z ARCING THEN DEAD R412 HOT, FOP CHIP KA2131 ,R807 11K
CI3312Z COLOR INT LOST X501 8.8MHX XTAL - TO SET UP SHORT PINS 1 & 6, 21 & 22 OF IC501 & ADJ CV01 FOR FLOATING PIC
CI3312Z DEAD R823 IN 12V REG FEED & R411 ACROSS PRI LINE DRIVER TRFMR
CI3312Z FIELD COLLAPSE R307 33K HI RES
CI3312Z HIGH HT BLOWS RESISTORS IN LOP STAGE R807 11K HAD INCREASED TO GIVE 157V HT INSTEAD OF 125V AT D821
CI3312Z LACK OF HEIGHT R302 470K HI RES
CI3312Z NEEDS DEGAUSSING REPEATEDLY REMOVE PLUG + SOCKET ON COILS
CI3312Z NO SEARCH TUNE - TUNING VOLTS STUCK AT 29.5V RQ01
CI3312Z NO SEARCH TUNING - TUNING RAIL STUCK AT 30V RQ01 DRY
CI3312Z NO SIGNALS NO 33V AT COLLECTOR OF RQ04 - RR05 10K ¼W
CI3312Z NO SND EXCEPT THRO' SCART IC601 CD4066BCN SW CHIP ,
CI3312Z NO SND R709 27K WHICH FEEDS IDENT SIGNAL TO PIN 29 OF MICRO RIC01
CI3312Z OVERSIZED PICTURE - SET ARCING OVER. 125V AT D821 HIGH R807(11K)GONE HIGH.
CI3312Z P58SC
CI3312Z P58SC DEAD WITH MAINS FUSE OR R601 5R6 7.5W C816(2N2 2KV)
CI3312Z PORTABLE P58SC
CI3312Z VOL AT MAX THOUGH OSD S R615 8K2 IN DC VOL CONT NETWORK
CI3312ZSTBY NO SCL SDA AT PINS 39 & 40 OF MICRO RIC01. RX01 10MHZ XTAL ,
CI3351
 CI3351 P68 INT DEAD WHEN HOT C808(330PF)
CI3351 THORN C15012R PORTABLE P68SC
CI3351A
 CI3351A DARK PIC C907 1NF 2KV DECOUPLING CAP ON CRT BASE LEAKY
CI3351A DEAD - NO START UP VOLTS PIN 4 IC801 CHIP , SDH209B
CI3351A INT DEAD WHEN HEATED WITH NO LED C808 330PF 2KV DISC CAP IN SNUBBER NETWORK - CHECKED OK OUT OF CCT
CI3351A LO WIDTH - D405 1N4003
CI3351A P68SC6 DEAD RESISTORS FEEDING PIN 4 IC801 IF OK IC801
CI3351X
 CI3351X DEAD IC801 SCH209B; R803 270K; R804 270K
CI3351X FIELD COLLAPSE - NO SND R418 1R
CI3351X INT GOES INTO SEARCH TUNE RX01 10MHZ
CI3351X INT GOING INTO SEARCH TUNING MODE. RX01(10MHZ),.
CI3351X INT INTERFERENCE ON PICTURE. AQUADAG EARTH LEAD LOOSE.
CI3351X INT LOSS OF COL LOOSE CONN BCGND ON CRT BASE
CI3351X INTERFERENCE ON PIC - INT AQUADAG EARTHING LOOSE
CI3351X NO COLOUR INT. LOOSE CONNECTOR BCGND ON CRT PANEL.
CI3351X NO RASTER - SND OK R925 2R4 2W
CI3351X NO RED OSD OK, IC501 TDA4661
CI3351X NO RED THO' OSD OK IC501 TDA4661
CI3351X NO SND OR RASTER - LED OK D402 KF105 ; R826 1R ; C908 1µ 250V - ON CRT BASE
CI3351X NO SND OR RASTER - STANDBY LED ON. D402(KF105),R826(1R),C908(1U F,250V)ON CRT BASE .
CI3351X NO TUNING DZ824 33V ZENER LEAKY; R822 15K 2W
CI3351X STUCK IN STANDBY. RD201(5.6V ZENER)LEAKY,IC802(MC7808).
CI3351X WILL NOT TUNE IN. DZ824(33V)LEAKY,R822(15K,2W).
CI3351XSTBY RD201 5V6 ZENER LEAKY; IC802 MC7808
CI3352
 CI3352 P68
CI3352 P68 DEAD - IC801 SDH209B , WHEN,125V HT WAS 170V DUE TO C852 470µ 16V ,
CI3352,
 CI3352AT
 CI3352X
 CI3352XT P68SC DEAD LOPTR(2SD1651),CAUSE HI HT(125VN),C852(470UF25V)
CI3352XT= P68 CHASSIS.
CI3373
 CI3373 SEE SCT11D 75W MADE IN TURKEY
CI3373 DEAD WITH FUSE BLOWN CHECK ZD8011 FOR
CI3373 FAINT PIC SET TO 'MILD' ON HANDSET - RESET TO NORMAL
CI3373 SCT11B/D HI STBY HT
CI3373 SCT11D
CI3373T S15A (MARKED CI3373T0X NEAR BARCODE) 2001, MANUAL 3S15A-SEH-1403
CI3373T SCT11D
CI3373T(Z) SCT11D
CI3373T4C SCT13B
CI3373Z DEAD 3.15A FUSE ; IC801 SMR40200 ; DZ801 R2KN ; L801 39MH DAMAGED ALSO HC801 HIS0169B HYBRID IC
CI3373Z FIELD COLL & POSS NO SND AFT STORM MICRO ,(£40)
CI3373Z S15A (MARKED CI3373Z5X NEAR BARCODE) 1999, MANUAL 3S15A-1402
CI3373Z SCT13B
CI3373Z SCT13B DEAD,RED LED FLASH,LOPTR Q401 PINS
CI3373Z SCT13B FIELD COLLAPSE,R409
CI3373Z4C SCT13B
CI338
 CI338 DEAD 800MAT DEGAUSS POSISTOR
CI338 DEAD FIT 1AT FUSE
CI338 DEAD LOPTR S/C AND R143 CHECK COIL L401 PINS AND DRIVER TX
CI338 DEAD. R413(1K), BU508.
CI338 INT SND S IC101 LA7520 IF CHIP
CI338 INT SOUND , LA7520 IF CHIP IC101.
CI338 NO BRILL NO A1'S SMALL ORANGE CAP ON CRT BASE PANEL USE 4KV.
CI338 P50 TASHIKO 14D971
CI338 P50 TASHIKO 14D971
CI338 P50 VERY ERRATIC & SUDDERN TUNING DRIFT AFFECTID BY MO CHECK FOR CRACK AROUIND PIN 1 OF SCREENED CONNECTOR SN01
CI338F NO COL WHEN WARM ZD501 LEAKY
CI338G P50F
CI338G P50F ROLLING ADD 470K FROM VR301/CHASSIS
CI338GA DIST SND R614 ; R601 2K7 HI RES
CI338GA FIELD ROLL, CLEAN FIELD HOLD CONTROL POTS
CI338GA INT BLOWING FUSE. 800MA WITH A 1AT ANTI-SURGE TYPE.
CI338GF FIELD COLLAPSE IC301
CI338GF P50F BOTTOM CRAMP IC301 PINS
CI338X P50 TUNER DRIFT, SN01 CONNECTOR
CI338X P50 TUNING DRIFT - SUDDEN & ERRATIC CRACKS AROUND CONNECTOR SN01
CI338X P50 TUNING DRIFT CRACK AROUND CONNECTOR SNO1 FROM REMOTE PANEL
CI338XA INT BLOWING FUSE. 800MA WITH A 1AT ANTI-SURGE TYPE.
CI338XF NO PIC SND OK,RESOLDER IC101(IN IF CAN).
CI338Z CHAN DISPLAY SHOWS "88" BUT CHAN OK CHECK TR805 & DZ809(5V SUPPLY PIN 24 IC4 LOW)
CI338Z DEAD - FUSE GONE. UPRATE FUSE TO 1AMP,R413(1R), BU508DF .
CI338Z DEAD MAINS TRANSFORMER OPEN CIRCUIT PRIMARY WINDING
CI338Z DEAD. MAINS TRANSFORMER PRIMARY .
CI338Z INT BLOWING FUSE. 800MA WITH A 1AT ANTI-SURGE TYPE.
CI338Z P36A
CI338ZSTBY IC003 µPD1987C , - NO O/P FROM PIN 6 TO TURN ON TR TO ENERGISE RELAY
CI339Z NO LINE DRIVE Q403 (2SC2229=BD131)
CI340 P50
CI340ZA INT BLOWING FUSE. 800MA WITH A 1AT ANTI-SURGE TYPE.
CI340ZA P50
CI347 P50
CI347 P50F
CI347F
 CI347F P50F
CI347FA INT BLOWING FUSE. 800MA WITH A 1AT ANTI-SURGE TYPE.
CI347FF
 CI347FF DEAD Q403 2SC2229 & Q402 2SC2120
CI347FF INT NO SND, RESOLDER IF CHIP UNDER PLATE.
CI347FF INT SND IC101 PINS
CI347FF INT SND RESOLDER IC101
CI347FF NO SND,RESOLDER ALL PINS IF CHIP INSIDE CAN.
CI347FF P50F
CI347FF SND INT S IC101 ETC UNDER SCREENING
CI348 14" HT=126 LT=20V. INT SHUTS OFF =KA2154.
CI348 IC601 OVERHEATS. C909(100NF)
CI348 INT BLOWS 2SD1650 Q404. DRYS C414.
CI348 INT BLOWS Q404 S C414
CI348 INT LOW CONTRAST PICTURE. DRYS ON FRONT POTENTIOMETERS.
CI348 INT LOW CONTRAST S ON FRONT POTS
CI348 INT LOW OR DIST SND S IC101(UNDER SHIELD)
CI348 INT SND - INT DISTORTED SND. DRYS IC101(UNDER SHIELD)
CI348 INT SND RESOLDER IF CHIP ,UNDER METAL SCREEN
CI348 NO SND. RL801 DIRTY CONTACTS.
CI348 P50
CI348 POOR COLOR R502(8K2)
CI348 SND , IC601 OVERHEATS C909 100NF
CI348 TRIPPING BROKEN PRINT NEAR L401
CI348 TRIPPING C461 1µ 250V; C414 0µ7 200V
CI348 TRIPPING Q404 2SD1650 ; R413 1K HIGH RES; S L401
CI348 TRIPPING. Q404(2SD1650),R413(1K), DRY L401,C461(1UF)C414(.47)PCB BY L401
CI3482
 CI3482 NO RED Q503 2SC2330 ON CRT BASE
CI3482 P58SC
CI348STBY Q404 2SD1650 ; R800 0R47
CI348Z C413(270PF2KV) SMOKING
CI348Z DEAD - HT LOW AT 40V C813 100µ 25V - ALSO CHECK C811, 808 100µ 25V & C812 1µ 50V
CI348Z FIELD INT ROLLS C351 0µ47 50V LEAKY
CI348Z NO SND - NO VOLTS TO AUDIO CHIP TDA2006 COMES FROM STANDBY RELAY WHERE CONTACTS WERE PITTED
CI348Z NO SND NO 18V SUPPLY ON PIN 5 TDA2006 STBY RELAY OC ON ONE CONTACT CLEAN OR
CI348Z NO SND, TDA2006 STANDBY RELAY.
CI348Z P50 INT FIELD ROLL C351 (0.47UF50V/0.22UF).
CI348Z P50 INT FIELD ROLL, C351 0.47UF, 50V
CI348Z P545 DEAD,LO HT, C813(100UF25V),UNDER R802,5W ,C808,C811(100UF25V)
CI348Z P54S LO HT(41V) 125VN, C813(100UF) UNDER R802.
CI348ZF INT SND RESOLDER IF CHIP.
CI348ZF TUNER UNIT ECU-5883CED
CI5
 CI5012 DARK PIC 5V6 ZENER PIN 8 RIC02
CI5012 DEAD R801 5R6 7W ; R807 2K7 3W ; P802(P160); R812 0R68 ; R813 100R
CI5012 DEAD. R801(5.6R 7W), 807(2.7K 3W), 812(.68R), 813(100R),P802(P160)
CI5012 FIELD COLLAPSE R412 1R 1/2W FUSIBLE
CI5012 NO COLOUR R522 2K HI RES
CI5012 NO LUMA )FIT INSULATED LINK FROM PIN 20 TO 16 B) 47R TO RGB I/PS ON PINS 7(BLUE), 11(GREEN),
CI5012 NO R/C FUNCTS JM02 5V6 ZENER LEAKY ON PIN 8 RIC02
CI5012 NO SND C605 22NF SC ON PIN 13 IC101
CI5012 NO SND. C605 22NF, FROM PIN 13OF IC101,
CI5012 NO SWITCHING CVBS-AV MONITOR VOLTS ON IC201 TEA20 CHECK RQ08 PIN 12 OF RIC01
CI5012 NO TUNING DZ824 KA33V LEAKY; R822 12K 2W
CI5012 P58SC
CI5012/5013 NO SND C605 22NF PIN 13 IC101 LEAKY
CI5012Z DEAD CHECK C816 220PF 1KV & R801 5R6 7W
CI5012Z DEAD R801 5R6 7W OC C816 SC 222PF 1KV
CI5012Z FIELD LIN C306 2µ2 50V
CI5012Z NO SIGNALS NO 33V AT COLLECTOR OF RQ04 - RR05 10K ¼W
CI5012Z P58SC
CI5012Z P58SC BRIGHT WHITE RASTER WITH FBACK LINES S ON CRT BASE THOUGH NOT OBVIOUS
CI5012Z POOR FIELD LIN. C306 2U2 50V
CI5012Z TRIPPING WITH TICKING NOISE MAINS SMOOTHING CAP 100µ 400V
CI5013 DEAD APART FROM NOISY PSU C808 100µ 16V, C817 100µ 25V
CI5013 NO SND C605 22NF SC ON PIN 13 IC101
CI5013 P58SC AKAI CT2115
CI50131T FIELD COLLAPSE R412 1R 1/2W SAFETY ; KA2131 FIELD CHIP; R305 20K
CI5013T
 CI5013T P58SC
CI5013T DEAD - NO LED R811 100K HI RES
CI5013T DRIFTS OFF TUNE & WON'T STOP IN SEARCH NO AFC I/P PIN 9 RIC01 MICRO - CHECK RES RR26 & R116 120K
CI5013T FIELD COLLAPSE. R306 .
CI5013T INT LOSS OF PIC - SND & TXT OK 27MHZ XTAL ON TXT BOARD
CI5013T NO STARTUP - NO STBY LIGHT. R811 100K PIN 8 TDA4600
CI5013T P58 DRIFTS OFF TUNE IN 5 SECS SEEK WON'T STOP R126 R116(120K)
CI5013T P58 HISSING IN C852 470µ 16V
CI5013T P58 PICTURE BLANKS INT SND OK TEXT OK 27MHZ XTAL ON TEXT PCB
CI5013T P58S CHANS WILL TUNE BUT NOT STORE RR53 3K3 PULL UP RES TO EEPROM CHIP
CI5013T P58S DEAD - Q801 CHOPTR C816 2N2 1KV IN PARALLEL R801 5R6 7W
CI5013T P58S NO SND & SWEEP TUNING WON'T STOP R709 27K
CI5013T P58SC AKAI CT2115
CI5013T P58SC INT NO START, STBY. 100UF 25V & 100UF 16V NEXT TO TDA4601 HEAT SINK.
CI5013T P58SC STBY NO 12V OR 16.5V MICRO 10MHZ XTAL US
CI5013T P58SC WONT START OR TRIPS,WITH NO SBY LIGHT CHECKR 811 100K
CI5013T P68
CI501FT S15A (MARKED CI501FT0X NEAR BARCODE) 2001, MANUAL 3S15A-SEH-1403
CI501FT S15A (MARKED CI501FT5X NEAR BARCODE) 1998, MANUAL 3S15A-0101
CI501FT5X HI BRILL/OFF ,ZD201(5V1)
CI501FZ S15A (MARKED CI501FZ5X NEAR BARCODE) 1999, MANUAL 3S15A-1402
CI5027 DEAD 4 X BRIDGE RECTS, STR50103, D801 R2KY CAUSED BY , SCAN COILS
CI5030
 CI5030 NO SND. X601 XTAL(STEREO SND
CI5030AN COLD OFF TUNE,C401.
CI5030AN H SYNC ADJUST OK
CI5030AN NO PIC FOR UP TO AN HOUR NO LINE LOCK - ADJ H SYNC PRESET
CI5030AN POOR TUNING COLD C401.
CI5030AN SCRN PATTERNING,C831(470UF25V)
CI5030AN SLIGHTLY OFF TUNE AT SW ON GRADUALLY IMPROVING C401
CI5030AN SLOW PIC, H SYNC PRE-SET TO THE CENTRE OF ITS LOCK-IN RANGE
CI5030AN US60AN
CI5052 P68 GOTO P68
CI5052 P68
CI5052 P68 "STORE" & "CHANNEL" IN FLASH ON SCREEN 1N4148 DIODES IN KEY STROBE LINES TO MICRO RIC01 LEAKY
CI5052 P68SA
CI5052 P68SW OSAKI C15013T
CI5052A
 CI5052A P68AT-SA
CI5052AT
 CI5052AT P68 GOTO P68
CI5052AT 127VVN 18VN 25VN
CI5052AT AGC DRIFT ADJUST T104.
CI5052AT FIELD COLLAPSE CHECK D412 AND R412
CI5052AT FIELD LOWERS WHEN WARM THEN BOUNCES IC402 MC7812
CI5052AT HEIGHT REDUCES WITH BOUNCE IC402 12V REG MC7812
CI5052AT P68SA
CI5052X
 CI5052X HIGH HT SHOULD BE 125V C852 470UF16V
CI5052X P68 OSAKI CI5013T
CI5052X P68 OSAKI CI5013T
CI5052X STBY 86V HT, R813
CI5052XT HUM BAR C851 100UF 400V MAINS SMOOTHER
CI5052XT NO SND/VIS WITH LED FLICKERING 125V HTSTBY 70V; IC801 SDH209B
CI5052XT P68 NO S/V,WITH SBY LIGHT FLICKERING SDH209B IC801
CI5052XT P68SC-M
CI5052XT P68SW/OSAKI CI5013T STBY LED FLICKER, SDH209B CHIP IC810.
CI5052XT STBY C852 470UF, C418 1UF 250V , Q402 2SD1651(LOPTR), R826 1R
CI5052XT= P68 CHASSIS.
CI5061
 CI5061 HT=125VN 133V STBY.
CI5061 P68SA
CI5061 FIELD INT TOP LINES , IC301
CI5061 FIELD TOP CRAMP IC301(KA2131) C307(1000UF) PIN9=25V.
CI5061 LINE SHIFT R420(820K) C404(2N7F)
CI5061 P68SA
CI5061 PIC SHIFTED TO RIGHT C404 2N7 & CHECK R420 820K
CI5061A
 CI5061AT FIELD COLLAPSE INT , CHIP
CI5070
 CI5070AN US60A DARK PIC D503 1N4003 DIODE HI RES - CHECK O/P FROM 12V REG IC802 - IT MAY BE LOW CONFIRMING , PART
CI5070AN US60A DEAD WHISTLE 241V, MAINS RECT
CI5070AN US60A DEAD WHISTLE LO 300V,C808(150UF400V)
CI5070AN US60A INT NO SND/PIC 1N4003 DIODES D801/2/3
CI5070AN US60A INT SND & BLANK RASTER D801 OR 2 1N4003 12V REG SUPPLY DIODES
CI5070AN US60A INT SND+PIC D801/2 D503, IN4003.
CI5070AN US60A LINE WHISTLE ,MAINS CAP LOW 320V.
CI5070AN US60A LOPTX WHISTLE/HUM, CASUE MAINS SMOOTHING CAP (LO 320V)
CI5073 SCT11D
CI5079 BLUE BLANK OSD TALL,EEPROM+MICRO RETURN TO DEALER.
CI5079 DEAD IC801(SMR4020),HC801,L803,ZD801
CI5079 DEAD SMR4020(NEW TYPE REMOVE ISOL WASHER),HIS0169C,DX801(R2KN)
CI5079 NO SND ,IC601 TDA7056A,R812(0R47)R813(0R47)
CI5079 NO SND,Q903(KSC815Y),Q907(KSR1012)
CI5079 SCT11D CRT CAP ARCING,HI HT? (125V)
CI5079 SCT13B
CI5079T
 CI5079T DEAD - 2 X 100UF20V R2K SMR40200C HIS0169B HYBRID CHIP & AUDIO O/P IC
CI5079T DEAD - LOPTR 2SD5072 ZD801, IC801, HC801,F801,L803,C803,C851,C852,Q401
CI5079T DEAD,PSU REPAIR KIT
CI5079T FIELD - TOP HALF MISSING FOP CHIP TDA8356
CI5079T HI HT AFTER REPAIR KIT,REMOVE IC801 MICA WASHER
CI5079T INT WIDTH SMR40200 IC IN PSU
CI5079T SCT11D BLUE SCREEN WITH NO SND - MENUS PARTLY OFF TOP OF SCREEN RESET EEPROM
CI5079T SCT11D EEPROM SETTINGS- WITH SAA5290ZP-026 SET OPTION BYTE TO 5D, WITH-042
CI5079T SCT11D EPROM SUFFIX EEPROM SET OPTION BYTE TO CA; PIN 1 OF MICRO TO CHASSIS - NEW MICRO REQD
CI5079T/Z SCT11B
CI5079Z DEAD -CHOPTR,AVALANCHE DIODE CAUSE HIS0169 HYBRID DEVICE - WITH HIS0169C C852 1N8
CI5079Z DEAD -F801 3.15A FUSE SMR40200 PINS 3-4, DZ801 R2KN,HC801 HIS0169B
CI5079Z DEAD IC801, L803, ZD801
CI5082 P69SA2 STBY. REMOVE EEPROM(24C02-
CI5102Z NO SIGNALS,TUNE VOLTS VARY BUT NO STATIONS RQ04,05,DZ824 33V 05 10K 0.25W
CI5103 P58SC
CI5103T P58SC
CI514 P36A
CI514 P50
CI514Z DEAD RELAY CLICKING C411 100PF 2KV SC
CI514Z P36A
CI515ZA INT BLOWING FUSE. 800MA WITH A 1AT ANTI-SURGE TYPE.
CI517 BLANK RASTER 2SC815 EQ101 MUTES THE IF SIGNAL WHEN THE SET IS IN THE VIDEO MODE,
CI517 INT COL -HIGH HT TA7698AP STR30125 POWER CHIP ,
CI517 P50
CI517Z BLANK SCREEN,IF AV SELECTED,SCART SIGNALS OK EQ101 2SC815
CI517Z BLANK WHITE RASTER EQ101(2SC815).
CI517Z STUCK IN AV MODE IF STRIP PERM MUTED AS EQ101 2SC815/2SC1815
CI517ZF DEAD 2KV 680PF .
CI517ZF DEADISH SMALL BLUE CAP 680PF2KV S/C ACROSS LOPTR.
CI517ZF LOW BRIGHTNESS C519 10N 2KV A1 DECOUPLER ON CRT BASE
CI5312 DEAD, SQEALS WHEN SW OUT OF C807 47µ 25V & C813 1µ 50V HI ESR
CI5312 U88MT
CI5312WSTBY - CHOPPER TFMR SQUEALS WHEN NOT IN C807 47µ 25V & C813 1µ 50V HI ESR
CI5322
 CI5322 FIELD COLLAPSE R412 & CHECK D401 ERB4304 ALSO C307 100µ 50V
CI5322 FIELD COLLAPSE R412 OC ALSO D401 AND C307(100UF)
CI5322 P68SC
CI5322 P68T
CI5322 TOPTEL125
CI5322T WIDTH COIL GIVES TUNING/IF FAULT CHEC 21" 32449-412-650 14" 32449-412-603
CI5322T DEAD C817(100UF).
CI5322T DEAD R801 5R6 7W ; C816 2200PF 1KV
CI5322T LED COMES ON BRIEFLY AT SW ON THEN DEAD C817 100µ LOW CAP
CI5322T NO SND / SWEEP TUNING NO STOP R709 O/C.
CI5322T POWER SURGE WARBLE DEAD ,C817(100UF)+C813(100UF).
CI5322T SWEEP TUNING DIDN'T STOP. R709
CI5322T WIDTH COIL L401. 32449-412-603 FOR THE 14IN. AND 32449-412-650 FOR THE 21IN.
CI5322XT P68T
CI5322XT BAD NOISE,HI HT(125VN),C852(470UF16V)
CI5322XT DEAD - PSU OVERWORKING & HT EXCESSIVE AT 250V CORRECT HT 125V WHEN C852 470µ 16V BUT R826 1R & LOPTR 2SD1650 ALSO
CI5322XT DEAD LOPTR(2SD1650)+R826(1R FUSIBLE).
CI5322XT P68T
CI5322Z P58SC
CI5330AN US60A
CI5332T EXCESSIVE VOLUME R625(10K).
CI5332T MAX SOUND OSD OK, R625 10K
CI5332T SND AT FULL BLAST EVEN WHEN TURNED DOWN R625 10K OC
CI5332T SND AT MAX & CAN'T BE TURNED DOWN - OSD OK R625 10K IN VOL DC NETWORK
CI5337 NO SND AFT WARM UP WITH SLIGHT DARKER PIC IC802 12V REG I/P & O/P LOW - D802 1N4003 FEEDING IT WAS LEAKY
CI5337 US60A
CI5337 US60A WARM NO SND/DARK PIC 2*12REGS ON SIGNALS BOARD,D802/IC802.
CI5337 US60A WARM NO SND/DARK PIC, D802 1N4003 DIODE
CI5337AN DEAD NO LINE DRV,D801(1N4007)
CI5337AN INT TEXT/PIC,IC804(5V REG)
CI5337AN PART FIELD COLLAPSE & DARK PIC IC802 12V REG - D801 1N4003
CI5337AN US60A
CI5337AN US60A LO HEIGHT, 7812 TYPE 12V REGULATORS IC801 AND IC802 1N4003 DIODE D801.
CI5337AN(US60A) PART FIELD COLLAPSE+LOW BRILL WHEN HOT ,D801 IN4003.
CI533CN S51A (CI533CN3X) 1999, MANUAL 3S51A-4417
CI533CN S51A (CI533CNG3X) 2001, MANUAL 3S51A-SEH-6201
CI533CN S51A GOOD SCART/NO TUNER ,RESET TO FACTORY STANDARD SETTINGS
CI533CN S51A NO RF SIGS SCART OK, ADJ IN FACTORY SETTING MENU
CI5344 SET OPTION3 FOR "CI", GO TO RESET, PRESS "VOL UP"(THE DISPLAY WILL SHOW "WAIT FOR 5 SECS"). FINALLY GO TO
CI5344 OPTIONS SET1 - TO RESET TO UK STANDARD - SW ON AT MAINS SW, USE R/C TO GO TO,
CI5344 OPTIONS SET2 KEY IN "DISPLAY", "MENU", "MUTE", & "STANDBY" IN QUICK SUCCESSION TO ENTER OPTION SET UP.
CI5344 POOR/NO COL, NO OR NOISY SND OR NO SYNC SETTING OPTION
CI5344 S51A RESET1, SET TO STBY THEN PRESS DISPLAY,MENU,MUTE,STBY
CI5344 S51A RESET2 SET TO CI,GOTO RESET VOLUP 5SECS(WAIT FOR 5SECS),STBY.
CI5344N NO CONTROLS DARK PIC1 ON BBC1.PRESS IN ORDER STANDBY, DISPLAY, MENU,MUTE, AND STANDBY THE TV WILL SWITCH ON WITH NO SND.YOU MUST CHECK THESE VALUES
CI5344N NO CONTROLS DARK PIC2,SCT = 16 SBT = 7 SCR = 5 ONCE THESE VALUES HAVE BEEN ENTERED
CI5344N NO CONTROLS DARK PIC3 SELECT RESET MODE. THE TV WILL RESET AND THEN SWITCH ON.
CI5344N S51A (MARKED CI5344N3X NEAR BARCODE) 1999, MANUAL 3S51A-4417
CI5344N S51A (MARKED CI5344NG3X NEAR BARCODE) 2001, MANUAL 3S51A-SE53-03
CI5361A
 CI5361A P68SA
CI5361AT P68AT
CI537 P55
CI537 P55 PRESS C THEN UP/DWN THEN PRESS/HOLD M TILL 'PR' SHOWS
CI537 P55 INT DEAD WITH RELAY CHATTERING RELAY & CHECK PH01 D/J
CI537 P55 NO RED 33K R803/811/818 ON THE CRT BASE PANEL
CI537 P55 ONE COLOUR R803/R818/R811(33K) ON CRT BASE PANEL.
CI537/41Z FLASHING ONE COLOUR THEN NO PIC R407 330K , 140K 190K IN LINK J52 AND FIT WIRE LINK IN PLACE OF R407
CI5373 SEE SCT11D SCT11B
CI5373 FIELD COLLAPSE CHECK R410
CI5373 LOSS OF TUNING, CONTRAST, GREEN, BRILL AFT POWER SURGE SET UP PROC REQD
CI5373 NO PIC/SND PSU NOISE,C801(150UF400V)
CI5373T
 CI5373T BLANK RASTER & LACK OF HEIGHT EEPROM & SET UP
CI5373T DARK PICTURE, GRADUALLY INCREASES LOPTX ,
CI5373T DEAD - PSU TRIPPING DZ801 R2K ACROSS HT,ALSO C851 22µ 63V
CI5373T DEAD -IC801 , ZD801 & HC801
CI5373T DEAD C803(2N2F800V)+R802(100R)+R803(100R)+IC801+HC801+DZ801
CI5373T DEAD , DZ801, R2K C851 22UF, 63V
CI5373T DEAD C803,DZ801,HC801,IC801 AND R802/803
CI5373T DEAD IC801 SAMSA40100080, ZD801 SAMS32167401880 AND HC801 SAMS40100090.
CI5373T FIELD COLLAPSE, R410(1R) AND OR TA8445K.
CI5373T HISSY SND,ADD A 330PF CAPACITOR ACROSS C223.
CI5373T LO FIELD AND NO VIDEO OR SND OR RESET EEPROM IC
CI5373T NO LUM ON PIC OR TXT EEPROM CORRUPT - ENTER SERV MODE(SEE MICK STUART)
CI5373T S15A (MARKED CI5373T5X NEAR BARCODE) 1998, MANUAL 3S15A-7349
CI5373T SC11B DEAD IC801 S/C +ZD801+HC801.
CI5373T SCT11B
CI5373T SCT13B (MARKED CI5373T4X NEAR BARCODE) 1998, MANUAL 3SCT13B-7310
CI5373T SND HISS,ADD 330PF ACROSS C223.
CI5373T SND SIBILANCE ADD 330PF CAP ACROSS C223(FRONT RIGHT CORNER)
CI5373T TRIPPED ZD801(R2K)+C851(22UF63V) CAUSE HI HT.
CI5373Z DEAD - SMR40200 CHOPPER IC , HC801 HYBRID IC WITH HIS0169C & R2K AVALANCHE DIODE
CI5373Z DEAD SMR40200 CHOPPER IC HC801 HYBRID IC HIS0169C,R2K AVALANCHE DIODE
CI5373Z SMR40200 CHOPCHIP +HC801 HYBRID IC(HIS0169C)+R2K ZDIODE.
CI5377 DEAD STRS6707
CI5377 NO PIC LOPTX
CI537V BLANK RASTER, TUNER, WHERE THE VIDEO SWITCHING IS CARRIED OUT
CI537V BLANK SCREEN - FIELD COLLAPSE FOP CHIP TDA2653A
CI537V DEAD - NO LED XF001 12MHZ XTAL
CI537V DISPLAY BUT NO LINE DRIVE D912 IN SUPPLY TO LINE OSC LEAKY
CI537V FIELD COLLAPSE R420(1R)
CI537V FIELD ROLL FROM COLD & ON CHAN C307 0µ47 50V TANT
CI537V INT DEAD CHATTERING RELAY. REL901 CONNECTOR PH01 PIN 3, THE PINK LEAD.
CI537V INT DEAD WITH CHATTERING RELAY REL901 CAN BE , OR BROKEN PIN 3 IN CONNECTOR PH01
CI537V NO LINE DRV,D912
CI537V NO STBY DASH,XF001(12MHZ XTAL).
CI537V P55
CI537V P55 BLANK RASTER - WORKS ON VIDEO INPUT TUNER UNIT US
CI537V P55 BLANK SCREEN. IC TDA2653A DUE TO LACK OF HEATSINK COMPOUND.
CI537V P55 CHOPTX PINS.
CI537V P55 CONTRAST LOW & UNADJUSTABLE. 12K RES ON FRONT PCB.
CI537V P55 DEAD - PSU WORKS BUT NO STANDBY DASH. XF001(12MHZ)XTAL,D912.
CI537V P55 DEAD 12MZH CRYSTAL XF001 D912,
CI537V P55 INT CONTRAST,12K ON THE FRONT MICROCONTROLLER PCB,
CI537V P55 NO PIC,TDA2553A FIELD CHIP.
CI537V P55 STBY D912 OC NO LINE OSC START UP SUPPLY
CI537V P55 TUNER MOD1 WITH ECC-2885PLE(S)TWO PINS ON LEFT AND READING L-R - BU - VT -
CI537V P55 TUNER MOD2 BH - AGC - BL - AFT - OLD UNIT = 34519-990-040 ECU5883PLE,NEW = 34519-9
CI537V REPEATED FAILURE OF Q901 CHOPPER TR 2SC3552 R910 270K HI RES
CI537V STUCK IN AV MODE TUNER WHERE SWITCHING IS CARRIED OUT
CI537V TDA2653A FIELD OUTPUT CHIP ADD HEATSINK COMPOUND
CI541 P55/P58?
CI541 P58SH
CI5412
 CI541ZG DEAD LOPTR(2SD1555 D+(47R)/S2055) CAUSE INT DRIVERTX(2849-020-010)
CI541ZG DEAD LOPTR(2SD1555 D+(47R)/S2055) HI HT ? (125VN)
CI541ZG DEAD WITH RELAY CLICKING C411 100PF 2KV IN LOP STAGE
CI541ZG FIELD COLLAPSE TDA3653B+R412 .
CI541ZG FIELD COLLAPSE. R412(1R 1/2W FUSIBLE).
CI541ZG INT INTO STBY CHOPPER TX PINS.
CI541ZG INT PIC /FLASHES ,X201 PINS,IF CAN LID TOUCHING CAP
CI541ZG INT SHUT DOWN INVISIBLE S AT CHOPPER TRFMR
CI541ZG INT TO STBY , PINS OF THE CHOPPER TRANSFORMER
CI541ZG NO RED MAY BE INT. DRYS Q556(CRT PCB)
CI541ZG NO SND - SET TRIPPING - BLACK BARS ON PIC. B5 RAIL @ 3.4V INFRA RED RX LEAKY(UNPLUG PA01 - 5 RAIL RESTORED)
CI541ZG P585H DEAD RELAY CLICK, PSU CAPS
CI541ZG P58SH
CI541ZG PSU & LOPT PULSING - NO SND. B5 RAIL @ 3.4V INFRA RED RX LEAKY(UNPLUG PA01 - 5 RAIL RESTORED)
CI541ZG SND CRACKLING & CUTTING OUT. R618(5.6K)NEAR AUDIO IC.
CI541ZG STUCK IN STANDBY. Q402(2SD1650).
CI541ZG WILL NOT LOCK INTO CHANNELS - NO SND. B5 RAIL @ 3.4V INFRA RED RX LEAKY(UNPLUG PA01 - 5 RAIL RESTORED)
CI591
 CI591 DARK PIC WITH RINGING CAPS IN 175V SUPPLY TO RGB LOW - C560 2µ2 400V ON CRT BASE & C410 220µ 200V ON MAIN PCB
CI591 NO SND NO/DARK PIC, C41 4.7UF, 400V HAD A BULGING CASE
CI591 NO/POOR PIC LO VIDEO VOLTS C560 2U2F400V ON CRT BASE +C410(220UF200V).
CI591 POOR/NO PIC 175VN. C560 2.2UF, 400V C410 220UF; 200V,
CI591 SND OK NO PIC C41 4U7F400V.
CI5913 & CI6813 BRILL HI,C560 2µF250V(ON CRT BASE) C410 OR C401 TO 47µ 250V. -VE PIN TO CHASSIS. C416 TO 47µ 250V.
CI5913 C416, TO 47UF, 250V, R415 0.47OHM, 0.5W
CI5913 CI6813 U88 C560(2.2MFD / 250V)CRT BASE. C410 TO NEW TYPE AND CAY OUT MOD
CI5913 CI6813 UU88 DARK PICTURE , C416(155V SMOOTHING) WITH 47MFD 250V
CI5913 U88 HIGH FREQUENCY VIBRATION NOISE FBT VIBRATION,AND FBT(3 HOLE FIXING TYPE), BOND R414 ,
CI5913 U88MT
CI5913 U88MT C560 22UF, 250V, C410/C401 220UF, 100V TO 47UF, 250V, AND NEGATIVE PIN TO CHASSIS.
CI5913 U88MT C560(2U2F250V)+C401(220UF250V)+C416(47UF250V)+R415(0R47).
CI5913W EXCESS WIDTH & NO E-W CORR C416 2U2F 250V IN ANTI BREATHING CCT
CI5913W EXCESS WIDTH EW C416 2.2UF, 250V,
CI5913W EXTRA WIDTH/EW DISTORTED C416(2U2F 250V).
CI5913W NO PIC - SND OK WHEN A1 ADVANCED DIM, WIDE PIC SEEN. HT CORRECT BUT HAD NOISE SUPERIMPOSED ON IT. C41 4µ7 400V U/S
CI5933 U88MT
CI5935 P70
CI5935T P70
CI5935Z P70
CI5937 Z68
CI5937AN DEAD & WHINING - D808 R2K 170V OVERVOLT DIODE OPTOCOUPLER PC801 PIN 2 - CAUSING NO FBACK OR HT REG
CI5937AN DEAD EXCEPT FOR SQUEAL FROM PSU ALL SEC SUPPLIES LOW - 32V LINE HAS A LOW RES READING - AUDIO O/P CHIP TDA2161 AT SUPPLY PIN 7
CI5937AN DEAD TDA2616A AUDIO O/P CHIP
CI5937AN DEAD TDA2616A AUDIO OUTPUT
CI5937AN DEAD WHINING.R2K, 170V OVER VOLTAGE ZENER DIODE D808 OPTOCOUPLER PC801
CI5937AN SET WHINES NO PICTURE OR SND D808 170V OVERVOLTS ZENER SC PC801 OPTOCOUPLER ED
CI5937AN STBY FAULTY USER CONTROL PANEL, DIS CN007 AND USE REMOTE.
CI5937AN STBY USER CONTROL PANEL AT FRONT ,UNPLUG CONNECTOR CN007 AND USE REMOTE
CI5937AN Z68
CI5937AN Z68 LO HEIGHT TDA8350Q
CI5937AN Z68 LO WIDTH RAGGED VERTICAL,C828(250V)
CI5937AN Z68, DEAD TDA2616 SND IC S/C.
CI5937ANSTBY MICRO NOT GIVING POWER ON SIGNAL. FRONT PANEL ,(WORKS BY R/C WHEN DIS'D)- NLA
CI593CN COLD DEAD,EHT OK,FRONT CONTROL PANEL FAULTS LEAKY SWITCHES.
CI593CN DEAD EHT OK, THE 5 FRONT PANEL CONTROLS.
CI593CN DEAD EY30 JOINT IN PSU
CI593CN DEAD SQUEEL,LOPTX(FUH-29A003(S)/SEME{LOPTX1282}) HI HT (130VN) CHOPIC(3S1265R)
CI593CN KS2A (MARKED CI593CN8X NEAR BARCODE) 2001, MANUAL 3KS2ATSE-2501 MICRO SIM806EW1
CI593CN KS3A (MARKED CI593CN8X NEAR BARCODE) 2000, MANUAL 3KS3A-2801 MICRO SDA555X
CI593CN S51A (MARKED CI593CN3X NEAR BARCODE) 1999, MANUAL 3S51A-4417 MICRO SAA5297M1A
CI593CN S51A (MARKED CI593CNG3X NEAR BARCODE) 2001, MANUAL 3S51A-SE53-03 MICRO SAA5553PS/M3/0029
CI593CN S51A DEAD IC801,C807(2N2F800V)
CI593CN SCT12B (MARKED CI593CNX NEAR BARCODE) 1998, MANUAL 3SCT12B-9301 MICRO SAA5297PS/230
CI593CN VARIOUS INC VOL VARIES, CHAN COUNTS UP/DOWN FRONT CONTROLS VARYING IN RESISTANCE
CI593CN3X S51A NO PIC/SND EEPROM 24W16 RESET OPTION BYTE SYSTEM CI
CI593CN3X SERVICE MODE, SET ON,REMOTE PRESS STBY,DISPLAY,MENU,MUTE,AND POWER ON
CI5944 DEAD LO HT(53v)EEPROM CAUSE LOPT ARCING WHEN HOT
CI5944 FIELD COLLAPSE TDA8350Q IC301 - IC301(VERSION 6 SUPPLIED WITH KIT) R307,R409,& R412
CI5944 FIELD PROBLEMS MOD KIT AVAILABLE FROM CHS(MODKIT10)INCS MOD SHEET
CI5944 SCT12B
CI5944 SCT12B FIELD COLLAPSE,LO WIDTH ,TDA8350Q KIT SEME(RK312)
CI5944 SCT12B TDA8350+R307+MOD KIT.
CI5944/683 SCT12B FIELD COLLAPSE TDA8350Q REPAIR KIT SEME RK312
CI5944N SCT12B
CI6229 P72
CI6229 U88MT1 FIELD IC301 ADD 1N4148 FROM PIN 3 IC301 ,ANODE TO GROUND ADD 12PF CERAMIC FR
CI6229 U88MT1 FIELD IC301 ADD 1N4148 FROM PIN 9 IC301 TO PIN 3 IC 301 ANODE TO PIN 3
CI6229T FIELD CHIP MOD REMOVING LINK PJ28 AND IN IT'S PLACE FIT A 10UH CHOKE. ADD 470NF100V FROM PIN 5
CI6229T INT DEAD OR DOES NOT SWITCH ON FROM COLD C806 100MFD25V
CI6229T P72
CI6229T P72 / U88MT
CI6229T P72 NO PIC UNLESS A1 ADVANCED - LOOKS LIKE FAILING MONO TUBE C416 2µ2 250V HT DECOUPLER
CI6229T(P72 CHASSIS) SILVERY VIDEO C416(2U2F250V).
CI6230 
CI6230 (U88MT1) DEAD SQUEAL C416(2U2F250V).
CI6230 DEAD C416 2µ2 250V BLASTED - CHECK D814 RU4AM - BYW95C DOES
CI6230 FIELD COLLAPSE TDA3654? 26VN/ WEAK TUBE .
CI6230 FIELD NON LIN AND SHORT PIC TDA3654
CI6230 HOT TOP F/BACK LINES FIELD O/P CHIP +BOOST CAP.
CI6230 LINE COLLAPSE CAP 2U2F 250V (4U7F 400V) NR TP155.
CI6230 NO SND - OK VIA SCART AUDIO IN AT TDA8415 IC601 OK BUT NO O/P - NO OSC DUE TO 10MHZ XTAL BEING U/S
CI6230 NO SND ,TDA8415+XTAL 10MHZ.
CI6230 P72
CI6230 P72 U88MT
CI6230 U88MT 1 DEAD PSU NOISE, C416 2.2UF, 25V
CI6230 U88MT1 DEAD,SQUEAL C416(2U2F250V).
CI6230 U88MT1 FIELD COLLAPSE , IC301 ADD 1N4148 FROM PIN 9 IC301 TO PIN 3 IC 301 ANODE TO PIN 3 ADD 1N4148 FROM PIN 3 IC301 ,ANODE TO GROUND ADD 12PF CERAMIC FR
CI6230 U88MT1 ODD VIDEO - NO COLOUR CHECK 12V SUPPLY FROM REG.
CI6230 UM88MT-1 FIELD COLLAPSE TDA3654 FOP CHIP+MOD
CI6230 UM88MT1 TDA3654+FIT COIL(10UH)IN LNK PJ28+ADD 470NF100V TWEEN PINS 4/5.
CI6230STBY C808 & 806 100µ 25V
CI6230WM
 CI6230WN DEAD PULSING C560 2.2UF, 250V
CI6230WN DEAD WITH SQUEAL C416 2µ2 250V IN LOP SUPPLY
CI6230WN DEAD/POOR START,100UF, 25V CAPACITOR C806.
CI6230WN FIELD COLLAPSE TDA3654+100UF53V(220UF50V105DEG).
CI6230WN NO R/C OPERATION MICRO IC701 HAD DEVELOPED INTERNAL WHICH MADE PROT LINE GO LOW- PCA84C840/062
CI6230WN POWER PULSING, TUBE BASE PANEL. C560 2.2UF, 250V
CI6230WN PULSING PSU & TRIPPING C560 2µ2 250V ON CRT BASE - ALSO CHECK C590 - REMOVE PLUG BY LOPTX TO CRT BASE TO CHECK THIS FAULT
CI6230WN TRIPPING C56 2U2 250V,C590 ON TUBE PCB USE 450V TYPES
CI6230WN TRIPPING C560 2U2F250V CRT BASE, C590
CI6230WN WON'T COME OUT OF WHEN COLD C806 100µ 25V
CI6231
 CI623CN FIELD COLLAPSE TDA8350Q ; R307 10R 1/2W FUSIBLE
CI633CN NO PIC/SND,REDUCE A1'S WARM FOR 20 MINS THEN INCREASE
CI6373 SCT11B FIELD COLLAPSE VPG101(HIC301)HYBRID IC
CI6373 SCT11B LOPTX ARCING
CI6644N FIELD COLLAPSE TDA8350Q ,R307,R409
CI6644N FIELD TOP LINES R307 R409
CI6813 C416, TO 47UF, 250V, R415 0.47OHM, 0.5W
CI6813 U88MT
CI6813 U88MT C560 22UF, 250V, C410/C401 220UF, 100V TO 47UF, 250V, AND NEGATIVE PIN TO CHASSIS.
CI6813 U88MT C560(2U2F250V)+C401(220UF250V)+C416(47UF250V)+R415(0R47).
CI6813W LOPTR(BU508AF1) CAUSE ? HT=156VN.
CI6813W NO PIC GOOD SND C416 2U2F250V (4U7F WILL DO)
CI6835 P70
CI6835T P70
CI6835Z P70
CI6837AN Z68
CI6837AN DEAD - WHISTLES EVEN IN IC603 TDA2616 AUDIO O/P CHIP INTERNAL UNDER LOAD
CI6837AN DEAD:WHISTLED TDA2616 IC603
CI6837AN SET WHINES NO PICTURE OR SND IC603 TDA2616 SC INT.
CI6837AN WHITE DOTS ACROSS SCREEN & NO SND 5 & 12V SUPPLIES LOW DUE TO 15V LINK WIRE TO REGS
CI6837AN Z68
CI6837AN Z68 5 LINES ACROSS BOTTOM IC301 TDA8350Q FIELD/EW CHIP
CI6837AN Z68 FLYBACK LINES TDA8350Q.
CI6837AN Z68 LARGE SPOTS /EW RASTER +NO SND 12V REG PINS+15V REG PINS.
CI6837AN Z68,FLYBACK LINES TDA8350Q.
CI683CN TOP HALF OF FIELD SCAN MISSING TDA8350Q FIELD IC
CI683CNG DEAD/STBY C407(1NF2KV)
CI683CNG S51A
CI683CNX WIERD LINE SPEED RAGGED,LINEDRV TX PINS.
CI6844 DEADISH 9V OK NO 5V TDA7297.
CI6844N WIERD LINE SPEED RAGGED,LINEDRV TX PINS.
CI6844N DEAD, TDA350Q-05,C804(100UF35V)
CI6844N SCT12B DEAD LED FLASHING YELLOW, 32.768KHZ CRYSTAL X901.
CI6844N SCT12B DEAD STR6709+Q805(TIP102 DARL).
CI6844N SCT12B DEAD: IC801 STRS6709 AND Q805 (DARLINGTON TYPE TIP102)
CI6844N SCT12B LED FLASH ING IC901/X901 32.768KH.
CI7230 PIC SHIFTED TO LEFT WITH EW MOD DR TR SMOKING ANODE D405 BYD33 IN LOP
CI7230 U88MT
CI7230 U88MT 1 LEFT PIC SHIFT D405 BYD33 IN THE LINE OUTPUT STAGE.
CI7230 U88MT PIC SHIFTED LEFT. D405(BYD33)IN THE LINE OUTPUT STAGE.
CI7230 U88MT PICTURE SHIFT, D405(BYD33)IN THE LINE OUTPUT STAGE.
CI7230 U88MT1 CHASSIS SHIFT D405 PINS (BYD33).
CI7230WN U88MT-1 NO COLOUR 5V ZENER D503.
CI7230WN U88MT1 NO COLOR TDA4661 OR ZD503(5V).
CI8644N TOP TEXT LINES,R307(10R)
CICI6229 FIELD COLLAPSE C808 IC301
CJ4581 TOP FOLDOVER C448(100UF).
CK-5320ZR SCT11D FIELD COLLAPSE R410(1R) D403
CK-5320ZR(SCT11D)FIELD COLLAPSE R410(1R) D403
CK5012T DEAD HT VLO PULSING , C807(100UF400V)
CK5038 SEE SCT11B
CK5038 SCT11B SERVICE MODE1 STBY --> P.STD --> HELP --> SLEEP -->POWER ON.
CK5038 SCT11B SERVICE MODE2 CONTROLS: VOL +/-, CH +/-. EXIT: STATUS.
CS3339Z NO PIC/SND IC TDA6107Q ON CRT BOARD
CS3339Z NO PIC/SND IC TDA6107Q ON CRT PCB
CS6226Z LOPTX ARCING
CS6818 Z66/RM11
CS721 SEE SCT52A
CS721 SCT52A SERVICE MODE PICT OFF -> SLEEP -> P.STD ->MUTE -> PICTURE ON
CS723 SEE SCT52A
CS723 SCT52A SERVICE MODE PICT OFF -> SLEEP -> P.STD ->MUTE -> PICTURE ON
CS7272 SCT51A SERVICE MODE PICT OFF --> SLEEP --> P.STD -->MUTE --> PICT ON
CS7272 SCT51A SERVICE MODE PICT OFF THEN SLEEP THEN P.STD THEN MUTE THEN PICT ON
CST12B FACTORY MODE SERVICE MODE THEN: SET PSL=15 AND PVA=63.EXIT: STATUS
CT566 K51A DEAD IC901(SZM-368ET2)
CT566(K51A) DEAD IC901(SZM-368ET2)
CW2144TN KS3A GOTO KS3A
CW21A113V NO SND,SOUND PROCESSOR(MSP34000G) , RESET EEPROM
CW28C33N DEAD. CAP ON 200V LINE (ON TUBE BASE)
CW5012 P54
CW593 STBY LED FLASHING ORANGE & STRAINING PSU C814 ACROSS D802 & HT SUPPLY
CW593 STBY, LED ORANGE FLASH C814,D802.
CX-6844N PARTIAL FIELD COLLAPSE IC301 TDA8350Q, 2 CAPS NOT MARKED 10µ & 100µ 63V, CERAMIC 10R 5W RESISTOR ACROSS PINS 3/5 OF ABOVE CHIP
CX5012 LO SND, IC601(TC4066BP) NR IF CAN
CX5012 POOR SND IC601(TC4066BP)
CX5944 SEE SCT12B
CX5944 SCT12B
CX6844 SCT12B
CX6844 SEE SCT12B
CX6844N FIELD - PARTIAL COLLAPSE TDA8350Q IC301 & 2 CAPS NOT MARKED ON PCB 10µ & 100µ 63V & 10R 5W RES ACROSS PINS 3 & 5 OF IC301
CX6844N FIELD COLLAPSE TDA8350Q 10µF & 100µF63V & 10R 5W RES ACROSS PINS 3 & 5 OF IC301
CXC1912 TV/VCR. DEAD ,LOPTR,LOPTX STRS6309
CXC1912 TV/VCR. DEAD LOPTR, STRS6309
CZ21A083N KS1A
CZ21A8VN
 CZ21A8VN TOSHIBA 21S04 KS3A
CZ21A8VN DARK PIC A1'S/G2 CONTROL POT IN LOPTX
CZ21A8VN DEAD FB802(630MA),LOPTR(T444)
CZ21A8VN DEAD HI HT,R821
CZ21A8VN DEAD IC801S FP801S(5A)
CZ21A8VN DEAD IC801S(3S1265R),DZ803(MTXJ30D),R821(133K)
CZ21A8VN DEAD IC801S(KA3S1265A),C81,DZ808(7V5)
CZ21A8VN DEAD IC804(KA7806 6V REG),IC804(KA7806),D806(FM-G125),R828(1R)
CZ21A8VN DEAD IC901.Q908,IC803(8V REG 78R08),IC201S(VDP3112B) Q204,Q401
CZ21A8VN DEAD LOPTR(KSC5703),LOPTX(T444)
CZ21A8VN DEAD LOPTR(KSC5703),T401,Q402(KSC2073)
CZ21A8VN DEAD NO LED,IC903(78RM33),D801(1N5397GP-600V),D801(1N4007)
CZ21A8VN DEAD NO LEDS,MICRO PRO,IC901
CZ21A8VN DEAD R802(15K),R803(15K),R804(15K)
CZ21A8VN EXCESS RED IC503(TDA6101Q) OR CRT
CZ21A8VN FIELD COLLAPSE IC301(LA7845),R425(0R47),D401(RUZOA60V),DZ302(KTZJ24B),IC803(78R08)
CZ21A8VN FIELD DZ202(MTZJ5.6B),IC201S,IC301,C301,R424(0R47),DZ303(24)
CZ21A8VN NO PIC SND OK,NO CRT HTRS,R522/R523
CZ21A8VN NO PIC SND OK,R528,C511(10UF50V)
CZ21A8VN NO RED IC503(TDA6101Q) OR CRT
CZ21A8VN NO RF PIC SCART OK, TUNER/IF UNITS
CZ21A8VN NO SND D86(TVRIOG)Q906(KSC1815),IC601,IC602
CZ21A8VN NO SND IC901(TDA7297),R631(0R33),FA803(7AMP)D807,C820(3300UF)
CZ21A8VN NO SND IC901(TDA7297,14V PIN3/14),R631(0R33 EACH),FA803(7AMP)D807
CZ21A8VN NO SND TUNER UNIT
CZ21A8VN NO SND, IC601(MSP3411G)
CZ21A8VN ONLY RED BITS,R503(10K)
CZ21A8VN PSU NOISE C803(470UF)
CZ21A8VN SNOWY PIC TUNER UNIT
CZ21A8VN TOO BRIGHT/FLYBACK LINES, A1'S/G2 CONTROL POT IN LOPTX
CZ21A8VN TOO WIDE C426(270NF/430NF 400V)
CZ21A8VN TUNER DRIFT,TUNER UNIT(TUO15),ZD804(TZP33A)
CZ21D83NS DOUBLE PIC OR PIC SHIFT R414(15K)
CZ21D83NS LINE SHIFT R414(15K)
CZ21D83NS LINE SHIFT/DISTORT R414(15K)
CZ21D83NS PIC SHIFTED, R414(15K)
CZ21M063N NO PIC SCART SND OK,TDA9351PS/N3/3
FACTORY MODE=STBY,DISPLAY,MENU,MUTE,STBY
J54AC20 RED PIC,LINES,RZ127(3R9)
J54AC20 RED PIC,LINES,RZ128(3R9)
J54AC20 RED PIC,LINES,STK392-040
K3SA
KS1A (MARKED CI20F12ZSX) 2001, MANUAL 3KS1A-SEH-0917
KS1A 21" HT STBY=163V INT NO EHT, LOPTR 2SD2499
KS1A DEAD NO LINE DRV, HT=135V,IC201(TDA9351PS/N2/31)
KS1A LINE SHIFT,CR405S(4N7F),R44(15K)
KS1A(MARKED CI20F12TSX) 2001, MANUAL 3KS1A-SEH-0917
KS3A DEAD 5AT DEGAUSS POSISTOR WIDE LEGS
KS3A DEAD LOPTR LEAKING TO HEATSINK
KS3A DEAD LOPTR(2SD5703/BU2520AF),LOPTX(HR8585)
KS3A DEAD PULSING, LOPTR(2SD5703),CAUSE LOPTX
KS3A EXCESS BRIL/FLYBACK, R519(0R47),IC501(STV5109)
LE20S51BP NO PIC ,SND/OSD OK,VT&SF15/17/20 PLUS BN41-00641A
LE20S51BPX/XEU SLOVAKIA
LE32R41BD
 LO VOL CHILD LOCK PRESS VOL+ ON SET + REMOTE /.
LS19DOCSS/EDC POOR PIC SCART VGA OK,MPU CTRL PCB
M8LCDTV 1080P 2007
P50F DEAD , Q403 SC2229 AND Q402 2SC2120
P50F INT DEAD Q403 BD131.
P55 LOSS OF 1 COL R803/811/818 33K 2W ON CRT BASE
P58 DEAD/NOISE C808 100UF, 16V AND C817 100UF, 25V. IN PSU
P58 JUST SNOW, DZ824 RQ04. RR05 10K
P58 P58 NO SND. C605 22NF, FROM PIN 13OF IC101,
P58 TUNE/MEMORY DRIFT ,TWO 120K OHM RESISTORS, RR26 AND R116.
P58C DEAD - PRI HTSTBY C816 2200PF 1KV SPLIT, C808 & C813 100µ 16V & C817 100µ 25V LOW
P58C DEAD/STBY C816 2200PF 1KV , C808 & C813 100µ 16V & C817 100µ 25V LOW
P58C POOR CONTRAST - R210 120K OR 133K IN BEAM LIM
P58C POOR CONTRAST - CONTROL INEFFECTIVE R210 120K OR 133K IN BEAM LIM
P58C/AKAI CT2115UK LO WIDTH. R824, A 100R 2W COIL L824
P58CH FIELD COLLAPSE,R412(1R),D401
P58S SET OK, BUT POWER NOISY C808(100UF25V)+C817(100UF25V)
P58SC NO COLOR, SECAM STUCK R514(100K)
P58SC STUCK IN SECAM MODE R514(100K)
P58SC 3.15OR 5R6 C816(2N2F2KV).
P58SC AMNESIA, PCD8572 CHIP RIC02 R124 33K
P58SC ARCING/DEAD R412 HOT KA2131 CAUSE HI HT.
P58SC BOTTOM CRAMP, C306 2.2UF, 50V, WHICH IS BETWEEN THE LINEARITY AND HEIGHT POTS
P58SC BRIGHT/FLYBACK CRT PINS.
P58SC CRACKLE ON SND CRACKLE PRESENT AT PIN 12 TDA8305. C603 & 605 22NF
P58SC DEAD 320V OK, C816 2,200PF, 1KV, C808 C813 C817 100UF, 25V
P58SC DEAD 320V OK,C816(220PF1KV)+C808+C813+C817.
P58SC DEAD C816 2N2F1KV+R801(5R6).
P58SC DEAD C816, 5.6OHM 7W R801 BRIDGE RECT
P58SC DEAD R801 (5R6) O/C C816(222PF1KV) ACROSS CHOPPER_TR.
P58SC DEAD, C808(10UF50V)+C817(100UF25V).
P58SC DEAD,C808(100UF16V),C811(10UF50V),C813(100UF16V),C817(100UF)
P58SC DEAD,R811 100K
P58SC DEAD. 5R6, 7W R801 C816 222PF, 1KV
P58SC DEGAUSS PLUG WIRES.
P58SC EXCESS BRILL,RESOLDER ALL CRT BASE PCB
P58SC FIELD BOTTOM CRAMP, C306 2.2UF, 50V, BETWEEN THE LINEARITY AND HEIGHT POTS
P58SC FIELD COLLAPSE R412 DIODE FROM LOPTX
P58SC HI HT 112VN ,C811,R808,VR801
P58SC HI HT 125VN AT D821.T R807 11K
P58SC INT BLANK RASTER , 27MHZ CRYSTAL
P58SC INT DARK RASTER 27MZH CRYSTAL ON THE TEXT PANEL.
P58SC LACK OF CONTRAST R210,120K OF THE BEAM LIMITER
P58SC LO 320V LINE (100UF400V HOT)/HT=139VN LT=17VN/19VN.
P58SC LOPTX ARCING FCM2014FL= HR7616 CAUSE HT HT
P58SC LOW WIDTH + BURNING SMELL L824 OC OR ED
P58SC MAX SND. R615 8.2OHM IN THE DC VOLUME CONTROL
P58SC MAX VOL R615(8K2).
P58SC NO PIC,SND OK,C816(2N2F1KV) ACROSS CHOPTR
P58SC NO RED 2SC2330 Q503 ON THE CRT BASE PANEL.
P58SC NO RED 2SC2330 ON CRT PANEL.
P58SC NO SEARCH TUNE. RQ01
P58SC NO SND CD4066BCN CHIP IC601 2SC1815 TRANSISTOR Q601.
P58SC NO SND R709 27K,
P58SC NO SND TDA1013A
P58SC NO SND TDA1013A ,R617(220K)
P58SC NO SND, LOW SIGNAL IDENT R709(27K)HI.
P58SC NO TUNE STOP ON SEARCH
P58SC NO TUNING RQ01 PINS.
P58SC OSD OK NO RAMP TUNING 30V REG+10K.
P58SC PURITY DEGAUSSING PLUG.
P58SC R412 FIELD OUTPUT CAUSE HI HT
P58SC SND CRACKLE C603 AND C605 BOTH 22NF.
P58SC SND CRACKLE C603/C605(22NF).
P58SC STBY 10MHZ CRYSTAL
P58SC STBY, 2SD288 12V Q802 RQ11, PCA84C640 MICROPRO RIC01.10MHZ CLOCK CRYSTAL RX01
P58SC/AKAI CT2125 INT BLANK RASTER, 27MZH CRYSTAL TZ01 ON TEXT BOARD
P668SA DEAD LOPTR(2SD1651),C852(470UF16V,R826(0R47)
P68
P68 SEE T/V MAG DEC 1996, PAGE 113
P68 TV MAGAZINE 1996 DEC.
P68 B1=125V,B2=33V,B3=16V,B4=8V,B5=5V,B6=16V,B7=24V,B8=12V.
P68 DARK PIC LOW A1S C907(1NF2KV) ON SPARK BOARD.
P68 DARK PIC, 1NF, 2KV C907 ON THE TUBE'S BASE PANEL.
P68 DEAD - HT DROPS TO 70V WHEN BROUGHT OUT OF IC801 PIN 6 WAS LOW - CHIP ,(SDH209B)
P68 DEAD (F801) CHOPTR(2CS4236),C852(470UF 16V),LOPTR(2SD1651) C853( 100UF 160V)
P68 DEAD 2SD1651 S2000AF LOPTR+R826(1R)+C852(470UF16V) C811(10UF50V) HT=125VN.
P68 DEAD C852 470µ 16V, Q402 2SD1651, R826 1R ½W, C835 100µ 160V, R820 100R & Q802
P68 DEAD FORCE POWER ON,SHORT OUT Q805(C/E)
P68 DEAD LOPTX SMOKING(FCM-2014FL)
P68 DEAD R826 O/C + LOPTR
P68 DEAD SDH209B CHOPPER CHIP R803,R804
P68 FIELD AN5512/KA2131,C307(100UF50V),SCANCOILS.
P68 FIELD HEIGHT+STBY LIT =D403 LEAKY/R418.
P68 FIELD PART COLLAPSE,LO 12V,R419(10R)
P68 HI HT, SDH209B OR C852 (470UF, 16V).125VN
P68 INT BRIGHT SCRN CHOKE L901 330UH.
P68 INT EXCESS BRILL, L901(33OUH) ON 180V FEED.
P68 JUST SNOW, TUNER TECC2985VA14B
P68 LINE SHIFT D411/R416(47K) FROM LOPTX_2 .
P68 LOPTR (2SD1650 R+D) R826(1R0.5W)CAUSE C852(470UF16V) HI HT 125VN.
P68 LOPTR 2SD1650=2SD1554.
P68 LOPTR 2SD1651 S2000AF LINE DRIVER R411.
P68 LOW GAIN C104 FROM PIN 47 IC101.
P68 NO PIC SND OK RX01.
P68 NO RED OSD OK, CHROMA DELAY LINE CHIP TDA4661 IC501.
P68 OFF CHECK SDH209B IC801. D810/811 1N4148 & DZ825 & C852 470µ 16V
P68 OSD "STORE" IN4148 DIODES IN KEY STROBE LINES TO MICROPRO
P68 POOR CONTRAST R210(120K).
P68 POOR TEXT SYNC TIC04(TEA2014).
P68 SDH209B IC801,E DIODES D810/811 1N4148 7.5V ZENER DIODE DZ825. C852 470UF,
P68 SDH209B+D810/811+DZ825(7V5)+C852(470UF16V).
P68 SLOW CONTROLS,TX01(27MHZ)
P68 STBY. 2SC2331Y TRANSISTOR Q803, R819(270R 2W FROM Q803 COLL)
P68 STUCK IN STBY Q803+R819(270K).
P68 TOO BLUE R903(1K5) ON CRT BASE.
P68 TUNER DRIFT,C111(3U3F),C113(100UF),C604(47UF),C608(1UF)
P68 UNSELECTED SEARCH RD03/04.
P68 UNSELECTED SEARCH TRY O/C PINS 1320 OF RIC01 FRONT SWITCHES.
P68 WARM LO HEIGHT, MC7812 REGULATOR IC402.
P68 YELLOW CAST CRT FAULTY
P68AM DEAD C808, A 330PF 2KV-DISC
P68SA P68 THORN CT200R P68
P68SA DEAD LOPTR(2SD1651),C852(470UF16V,R826(0R47)
P68SA DEAD PSU OK, 1N4003 DIODE D404
P68SA INT BRILL Q905(2SA539Y) ON CRT BASE PCB.
P68SA LO WIDTH/WEAK LINE DRIVE, D405(1N4007).
P68SA NO LINE DRIVE D404 O/C.
P68SA NO PIC/SND IC803(5V REG),C858(220UF10V)
P68SA OFF NO LINE DRIVE - LINE DR TR COLL VOLTS MISSING. D404 1N4003
P68SC TOPTEL125 REMOTE
P68SC DEAD LOPTR(2SD1651/S200AF) CAUSE HI HT.
P68SC DEAD,SDH209B.
P68SC FIELD COLLAPSE R412 D401 (ERB4304) C307 100UF, 50V AND THE O/P CHIP.
P68SC HI HT 125VN C852(470UF16V) C811(10UF50V)C853 LOPTR(2SD1651) R826(1R).
P68SC NOISY PSU,LOPTR(2SD1651/S2000AF)+10R7W CAUSE HI HT C852(470UF16V)
P68SC WEAK RED, GREEN OR BLUE RD09 1N4148 (RD10/11)
P68STBY R819 270R 2W OVERHEATING - Q803
P68STBY R819 270R 2W OVERHEATING - Q803 LEAKY
P72 BUZZES THEN OFF C806 100µ 25V LEAKY CONNECTED TO PIN 9 TDA4601
P72 FIELD CHIP1 ADD 1N4148 TWEEN PIN 9 & 3 IC301(CATHODE TO PIN 9)& 1N4148 PIN 3 TO
P72 FIELD CHIP2 GROUND(CATH- PIN 3)ADD 12PF CAP PIN 3 TO GROUND
P85C CHIRPING NOISE & LED ON THEN TRIPS OUT AFTER 1/2 MIN C817 100µ 25V
P85C COMES ON WITH CHIRPING NOISE & LED ON THEN TRIPS OUT AFTER 40SECS C817 100µ 25V
PA-1111-05S 14V PSU 4PIN TOP,RESOLDER NR FUSE
PS42V4 DEAD POWER BOARD BN9601217A
Q9 PLASMA
R8 LCDTV
RESET A1'S 1 GET A BLANK SIGNAL FROM SCART
RESET A1'S 2 GET INTO FACTORY MODE
RESET A1'S 3 SELECT G2 ADJUST
RESET A1'S 4 TURN SCREEN VR TILL RED TEXT AT TOP TURNS GREEN
RESET A1'S 5 PRESS MENU BUTTON
RESET A1'S 6 SELECT VIDEO ADJUST 1.
RESET A1'S 7 CHOOSE ANY ITEM EG SELECT RED CUTOFF
RESET A1'S 8 CHANGE VALUE (SAY 5 TO 6 THEN BACK TO 5)
RESET A1'S 9 PRESS MENU (TO RETURN TO MAIN SERVICE MENU)
S15A
S15A SERVICE MODE CONTROLS: VOL +/-, CH +/-. EXIT: POWER OFF.
S15A SERVICE MODE STBY THEN DISPLAY THEN P.STD THEN MUTE THEN POWER ON. EXIT: POWER OFF.
S15A SERVICE MODE,STBY --> DISPLAY --> P.STD -->MUTE --> POWER ON.
S15A 3.15AT DEGAUSS POSISTOR
S15A CHOPIC(3S0680R) C805(2N2800V)
S15A DEAD DZ801(R2KN) OVERVOLTS PROTECTION DIODE +LOPTR(2SD5072) CAUSE HI HT
S15A HI HT IC801 MODULE+SMR40200+C851(22UF25V) (19/20"=125VN)
S15A NO BRILL/A1'S LOPTX(FSV-14A004{S})
S15A NO TUNING 33V R810(18K)
S15A NO TUNING IC901/IC902(KS24C041),33V OK,TUNER OK
S15A SND BUZZ ?
S51
 S51A 28" DEAD DZ805 (KA431Z); 160V OFF LOAD 130VN
S51A 28" DEAD LED YELLOW/ORANGE FLICK, DZ805 (KA431Z) 
S51A 28" DEAD LED YELLOW/ORANGE FLICK, LOPTX PINS
S51A CHASSIS, LED YELLOW TO ORANGE, HI HT(130VN) OPTO IN PSU
S51A DEAD C814(850PF 1KV) ACROSS D805
S51A DEAD PULSING,LOPTR(KSD5703)
S51A WARM NO SND,LOPTX HISSING(FUH-34A001(S)/HR8585 MOVE DIODE TO UNDERNEATH)
SCT
 SCT11A STBY 'P.STD', 'MENU', 'SLEEP',VOL+,VOL-,CH=,CH-
SCT11B DEAD SMR4020(NEW TYPE REMOVE ISOL WASHER),HIS0169C,DX801(R2KN)
SCT11B SERVICE MODE STBY THEN P.STD THEN HELP THEN SLEEP THEN POWER ON. EXIT= STATUS.
SCT11B STBY 'P.STD', 'MENU', 'SLEEP',VOL+,VOL-,CH=,CH-
SCT11B/D CI3373 CI5079 DEAD DZ801 IC801
SCT11B/D CI3373 CI5079 DEAD WITH DZ801 OR IC801 EXCESS HT ;HC801 C852
SCT11B/D DEAD , DZ801(0403000691).IC801,(AA1320004P VERSION C)HC801(AA13-20004M VERSION C.)
SCT11B/D HI STBY HT, C852 USING PART NO 2301-000111.
SCT11D
 SCT11D SEE TV MAG DEC 2002 P73
SCT11D BLANK BLUE SCREEN EEPROM SAA5290ZP - 026 THE OPTION BYTE SHOULDO 5D.
SCT11D BLANK BLUE SCREEN SAA5290ZP - 042 THE OPTION BYTE SHOULD BE SET TO CA.
SCT11D DEAD LOPTR LINE DRVER(KSC2331Y) T401
SCT11D DEAD WHISTLE LOPTR(2SD1711 45R+D)+REG SMR40200+2*47R
SCT11D DEAD ZENNER(R2K),SMR40200C+HIS0169B(HYBRID HC801)+100UF200V
SCT11D DZ81 OR IC801 S/C (AA1320004P VER C) C852 OFF LOAD HT=140V
SCT11D FIELD COLLAPSE R410 1R FEEDING D403
SCT11D INT WIDTH. SMR40200 IC IN THE POWER SUPPLY.
SCT11D JUST SNOW WON'T TUNED IN. MICROCONTROLLER CHIP
SCT11D LOPTR(2SD5072) WHISTLE/ REGULATOR SMR40200C+ THICK FILM HIS0169C.
SCT11D LOPTR(2SD5072)+ZD801+IC801+HC801+F801+L803+C803+C851+C852+Q401
SCT11D POWER SURGES SMR40200.
SCT11D SMR40200 FIT SMR40200C REMOVE MICA INSULATOR AND ENSURE EARTH GOOD
SCT11D SMR40200 FIT MOD KIT SMR40200C(LESS ISOLATOR)+ HIS0169C
SCT11D WARM ODD LINES ACROSS/OFF, SMR40200 MOD
SCT12
 SCT12B SERVICE MODE STBY --> P.STD --> HELP --> SLEEP -->POWER ON.
SCT12B 0 FIELD MOD TDA8350 IC301 FOLLOWING COMPONENTS SHOULD BE ADDED WHEN FITTING
SCT12B 1 ADD MTZ15C 15V, 500MW ZENER(DZ403) ACROSS C303 CATHODE TO PIN 3.
SCT12B 2 1N4004 DIODE PIN 9 AND THE 46V SIDE OF R307, WITH ITS ANODE TO PIN 9.
SCT12B 3 REMOVE L301/J394.AND FIT A 10UH AXIAL COIL (PART NO 2701-000116) 1.2OHM, 5%, 2W
SCT12B 4 FUSIBLE RESISTOR (PART NO 2008-001013) CONNECTED IN SERIES. THEN ADD FROM THE
SCT12B 5 JUNCTION OF THIS SERIES COMBINATION AND R302/R303/C301 TO CHASSIS, AND MA2560 56V,
SCT12B 6 1W ZENDER DIODE (PART NO 0403-001039) WITH A 470NF, 5%, 100V CAPACITOR
SCT12B 7 (PART NO 2305-000407) IN PARALLEL. ANODE OF THIS ADDED ZENER DIODE GOES TO CHASSIS.
SCT12B 8 THE EXTRA COMPONENTS CAN BE ADDED ON THE UNDRESIDE OF THE PCB, CHECK RESISTOR R307 SCT12B 9 10OHM, 0.5W,(PART NO 2008-000197) WHICH IF FAULTY, CAN CAUSE FLYBACK LINES
SCT12B DEAD IC801(STRS6709)& Q805 TIP102
SCT12B DEAD LED FLASHES YELLOW IC901 , XTAL X901
SCT12B DEAD NO LINE DRV,CAUSE IC601(TDA7297 AUDIO)
SCT12B E/W - TDA8350 CHIP FAILS MOD AVAILABLE
SCT12B E/W FAULT - TDA8350 CHIP FAILS MOD AVAILABLE
SCT12B FACTORY MODE: SET PSL=15 AND PVA=63.CTRLS VOL +/-, CH +/-. EXIT: STATUS
SCT12B FAILURE OF TDA8350 FOP CHIP ADD ADDITIONAL COMPONENTS TV FFINDING FEB 2000 GIVES DETAILS
SCT12B FIELD CHIP +MOD KIT.
SCT12B FIELD TDA8350 ADD ADDITIONAL COMPONENTS TV FFINDING FEB 2000 GIVES DETAILS
SCT12B FLYBACK LINE AT TOP OF SCREEN R307 10R
SCT12B NO POWER UP LED FLASHES YELLOW CHECK IC901 HAS 5V SUPPLY, OSC AT PIN 31,32 - IF NO OSC SUS XTAL X901
SCT12B SERVICE MODE STBY THEN P.STD THEN HELP THEN SLEEP THEN POWER ON.EXIT: STATUS
SCT13B SERVICE MODE STBY -> P.STD -> HELP -> SLEEP ->PWR ON.CTRLS: VOL +/-, CH +/-. EXIT: STATUS.
SCT13B SERVICE MODE STBY THEN P.STD THEN HELP THEN SLEEP THEN POWER ON. EXIT= STATUS.
SCT51A STBY 'SLEEP', 'P.STD', 'MUTE','VOL+' ET 'VOL-''CH+' ET 'CH-'.
SCT52A SERVICE MODE PIC OFF THEN SLEEP THEN P.STD THEN MUTE THEN PIC ON
SCV11A STBY 'P.STD', 'MENU', 'SLEEP',VOL+,VOL-,CH=,CH-
SCV11B SERVICE MODE STBY THEN P.STD THEN MENU THEN SLEEP THEN POWER ON
SCV11B /VCR SERVICE MODE STAND-BY --> P.STD --> MENU -->SLEEP --> POWER ON
SCV11B DEAD Q802(TIP102)+DZ802(7V5)
SCV11B STBY 'P.STD', 'MENU', 'SLEEP',VOL+,VOL-,CH=,CH-
SP32W5HG REAR PROJ,INT GREEN SIZE, ICZ104(STK392-040)
SP403J REAR PROJECTION, LED FLASHING LAMP LIFE EXPIRED(>6000HRS)
SP42W4HBX J54A4U4 42"RP LOPTR,LOPTX(BP94-00044A)
SP42W4HBX/XEU 42"REARPROJ, POOR CONTAST/FOCUS,CRT BASE SOCKET FOCUS PIN
SP42W5HF1 STBY,ICZ103(STK392040),R127(3R9),R128(3R9)
SP42W5HFX J54AC20
SP42W5HFX/XEU 42" REAR PROJ J54AC20
SP42W5HPX REAR PROJ NO GREEN,GRN CRT BASE PCB
SP42W5HSX PRJ,CONVERGENCE ADJ, MUTE,1,8,3
SP42W5HSX PRJ,CONVERGENCE,STK392-040
SP42W5HSX PROJ,ADJUS MUTE,1.8,3 QUICKLY
SP42W5HSX PROJ,CONVERGENCE IC'S(STK392-040),8*150R
SP43H3HTX COMBI TV/DVD PROJ
SP43H3HTX NO DVD PLAY, DZ814(30V),IC812S(KM1M05565R CHOPPER IC)
SP43W6HP BLUE CONVERGANCE ERRORS, STK392-040 IC
SP50L7HXX XEU PROJ
SV421 DX5R
SV821 DX5R
T P58S NO TUNINNG STORE EEPROM RR53. 3R3
T224C5 COMBI DEAD OPTOCOUPLER
TC2065SX DEAD TICKS, LOPTR,LOPTX
TC2065SX TIC NOISE ,D403.
TC9895TB DEAD FUSE. BRIDGE RECT(1N4007)
TC9895TB FUSE. 1N4007 BRIDGE
THORN CI5012R P68
THORN CT200T P68
TI14B7 COMBI WARM NO PIC, C503(1NF2KV)
TI14N3 COMBI LINE SHIFT,R410(3K9),DZ401,CR404,CR405
TI20C5DF2S DEAD RELAY CLICKING VCR SECT OK TDA8356 FIELD IC & R303 10R
TI20C5DF2S/XEV COMBI DEAD CLICKING RELAY , C414(680PF2KV).
TI20C5DF2S/XEV DEAD CLICKING DEGAUS RELAY C414 680PF 2KV
TI20C5DF2S/XEV DEAD DEGAUS RELAY C414 680PF 2KV BURNT & LEAKY IN LOP STAGE
TO6ZX Z66/RM11
TOSHIBA 21T01B(D,I,N) SAMSUNG KS1A AA41-00131G LPM-802EW
TVP-3350IS(SCV11C) NO RF AUDIO PCB NR TUNER
TVP-3350IS(SVC11C) STBY Q801(STRS6707)
TVP3350 COMBI SEE SCV11A
TVP3350 SCV11A
TVP3350IS SCV11C COMBI NO RF AUDIO RESOLDER BEHIND TUNER
TVP3350IS SVC11C COMBI STBY Q801(STRS6707)
TVP5050 COMBI SEE SCV11B
TVP5050 COMBI
TVP5050 COMBI SCV11B
TVP5050 SCV11A
TXB1940 COLD DEAD/LED BLINKS, R902, R901, R905, R903, R900A, Q902
TXB1940 DEAD LED BLINKS TILL WARM,R902, R901, R905, R903, R900A, Q902, Q902
TXE2746 FIELD LO HEIGHT, R417, R410, D404, DZ303 ,DZ305.
TXE2746 FIELD LO HEIGHT,ADJUST IN SERVICE MENU
TXE2746 STBY, REMOTE, PRESS MUTE-1-8-2-POWER ON.
TXE2746 LO HEIGHT R417, R410, D404, DZ303 AND DZ305.
TXE2746 LO HEIGHT,WITH SET OFF AND USING REMOTE, PRESS MUTE-1-8-2-POWER ON.
TXE2746 SERVICE MODE USE THE VOL UP/DOWN AND CH UP/DOWN TO SELECT PARAMETER. FOR VERTICAL HEIGHT SELECT VA.
TXG2547 K51A DEAD IC901(SZM-368ET2)DZ906
TXG2547(K51A) DEAD IC901(SZM-368ET2) DZ906
TXG2746 DEAD LOPTR 2SD1880. CB19 47NF 400V,RE04 6.8R 2W,,RE05 ALSO 6.8R 2W.
TXG2746 DEAD LOPTR(2SD1880) CB19(47nf400v),RE04(6R8) RE05(6R8)
VIK310 SEE TV MAG FEB 1997
VIK320 SEE TV MAG FEB 1997
VIK350 SEE TV MAG FEB 1997
VM3105 COMBI NO VIDEO, NO SND. PSU NOISE. R417 (1R)
VM3105 NO PIC/SND R417(1R)
VM3105 NO PIC/SND NOISE R417(1R)
VM3105 NO PIC/SND R417(1R)
VM6405 TV/VCR DEAD WHISTLE LOPTR[2SD1878] C810
VM6405 TV/VCR DEAD/NOISE,LOPTR(2SD1878) C810
VOYAGER 10
VOYAGER 10 STBY TUNER/TIMER CHIP. SAMSUNG PART CODE IS 32213-257 SIP.
VT306K TASHIKO 12D971
W124W6VN BRILL VARIES, LOPTX A1'S
W124W6VN PIC BRILL VARIES CAUSE LOPTX A1'/G2 POT
W132 SEE WI32
WI24W6VN BRILL ALTERS,LOPTX A1'S POT
WI24W6VN INT BRILL,LOPTX A1'S (FUH-34A001(S)/HR8585 MOVE DIODE)
WI24W6VN LO/NO BRILL LOPTX A1'S TOUCH RK TO TRIGGER ON
WI286VN NO PIC,C530(10NF3KV)
WI28W5 S51A
WI28W5VN INT POOR CONTRAST,CRT BASE SOCKET
WI28W6VD S51A CHASSIS TYPE UNDER LOPTX
WI28W6VD S51A WARM NO SND,LOPTX HISSING(FUH-34A001(S)/HR8585)
WI28W6VD SCT53A WARM STBY,DZ808(7V5)
WI28W6VN
 WI32W6VD3X XEU HAVE SOME INFO
WI32W6VD3X XEU EEPROM RESET,UNDO E/2 MEMCHIP PIN5,POWER UP,RESET,OFF,RESOLDER
WI32W6VD3X XEU NOTV SND AV SND OK,IF/NICAM PCB
WS24V53N EXCESS BRILL,STV5109,R519(47R) ON CRT BASE PCB
WS24W63N SNOWY PIC TUNER UNIT(TCPW3001PD16A(S)
WS24W63V KS3A
WS28M064N ET2806
WS28M64N
 WS28M64N BENT SIDES EW,IC401(LM393)
WS28M64N DEAD C405(6N3F1K6V),C406(SAME)
WS28M64N DEAD GREEN LED,C407(1NF2KV),IC201(VDP3112B)
WS28M64N DEAD GREEN LED,Q402(2SC2073),Q204(KSC1815)
WS28M64N DEAD LED BLINKS FB802(630MA) CAUSE LOPTX
WS28M64N DEAD TICKS,,LOPTR(2SD5703,CAUSE LOPTX(T444)
WS28M64N INT BRIGHTNESS,A1'S/G2 PRESET ON LOPTX
WS28M64N INT DEAD,HIC401(KSD5703),IC201
WS28M64N INT SND CRACKLE,IC601 MULTIPLE SOUND PORCESSOR
WS28M64N KS3A GOTO KS3A
WS28M64N LINE COLLAPSE SCAN COIL PLUG
WS28M64N POOR T/TEXT,RESET IN SERVICE MODE
WS28M64N SERVICE MODE,STBY,DISPLAY,MENU,MUTE,STBY
WS28V53N KS3A DEAD LOPTR(2SD5703) LOPTX(FUH34A001S)
WS28V53N NO GREEN,R508(82K) ON CRT BASE PCB
WS28W63N KS3A
WS28W6NG RELAY CLICKS,330UF200V ON HT LINE
WS28W6NS KS3A EHT FLASH TO DEGAUSS COILS
WS28W6NS KS3A TUNER UNIT BROKEN,ADVISED TO BUY FREEVIEW BOX
WS28W6V INT NO GREEN,HIC203(HYBRID THICK FILM)
WS32A116T
 WS32A116T POOR FLARING RED PIC,R506(82K)
WS32M64V KS3A BRILL VARIES RESET A1'S POT
WS32Z306V DEAD NO LINE DRV Q402
WS32Z306V DEAD TICKS LOPTX, Q403(2SJ920),Q402(BUZ73A)
WS32Z306V STBY CRT
WS32Z306V STBY Q402
WS32Z409T DEAD HT PULSING LOPTR(J6920A/2SJ6920A) CAUSE LOPTX
WS32Z409TQX/XEU CRT HDTV CATCH-ME AA1-01163A
Z68 TOP FOLD TDA8350.
Z68 TOP FOLDOVER TDA8350 FIELD /EW OUTPUT CHIP IC301.
GOTO TOP If you know of any fault repairs NOT here. Please email the info to me
your fault NOT here , try my step by step guide Do it yourself guide
Highlandelectrix