Press CTRL/F to search this page (no -)
TC1651,TC1655RE,TC1655UR,TC1657,TC2051,TC2061,
TC2203,TC2253,TC2262,TC2263,TCC23PFR,TX5500 ARE ALL SAME LOPTX.
TC221,TC2232,TC2233,TC2235,TC2238DR,TC2238UR,TC2245UR,TC2633,TC2634UR,TC2648,
TX2230,TX2231,TX2233,TX2234,TX2240UR,TX2244,TX2636,TX2640UR,TX2646 ALL SAME LOPTX
TC1457DR,TC1757DR,TC2110,TC2160,TC2168DR,TC2210,TCC22DR,TX1752,TX2112,
TX2122,TX2162,TX2168UR,TXC22,TXC22UR ALL SAME LOPTX.
'ONE4ALL REMOTE CODES 0226,0650,0250,0126,0240 0274 0214 0213 0361 0237
'ONE4ALL REMOTE CODES 0367 0340 0516 0037 0163 0548
'SKY REMOTE CODES PANASONIC 0051 678,254,278,154,242,241,368,128,191,368,395,585
PANASONIC SPARES WILLOUGHBY ROAD,BRACKNELL BERKSHIRE RG12 8PF
SEME LTD ,SCHOOL LANE BUCKINGHAM BUCKS MK18 1HD.
GOTO PANASONIC SPARES
PANASONIC
USE FASTTEXT BUTTONS TO CHANGE MENU AND SETTINGS.
14B3T Z375 TOO MUCH HEIGHT, ALTER IN SERVICE MODE
14B3T Z375 = DAEWOO CP375S
14B3T Z375 SERVICE MODE, CHAN70. SHARPNESS MIN. PRESS REMOTE OFF TIMER, SAME TIME PRESS V ON TV
14B3T Z375. POOR/SLOW START R804(0R56)
14B3T(Z375) TOO MUCH HEIGHT,ALTER IN SERVICE MODE
14B3T(Z375)SERVICE MODE,CHAN70.SHARPNESS TO MIN. PRESS BOTH R/C OFF TIMER AND TV DOWN
14B3T(Z375.)DAEWOO CP375S
14B3T(Z375.)POOR START R804(0R56)
1665 Z1
21LIT DEAD/STBY IC AN5606K
21LIT DEAD/STBY IC AN5606K
21V2 ALPHA 4
21V2 ALPHA4
21V2 DEAD - SQUEALING P.SUPP CHECK D851
2213 TX2 DEAD , SQEALING IC501 PIN 5 XRAY PIN. NORMAL C561 , 1 MFD , C809 , 1MFD , C853 , 100MFD , C854 , 47MFD
2375
25A3 EURO 1
25A3 EURO1 BELOW
25DN1 STBY R620, 621 120K
25MD1/B LINE TEARING, KIT VDP3108A PART NO. TZS9EK002
25TX1 E-W DISTORTION-NO ADJ C754
25X1DP ALPHA 4
25X1DP ALPHA4 GOTO ALPHA4
2622 BLANK RASTER WHITE FLASHES C326(1UF).
2622 TX2 DEAD , SQEALING IC501 PIN 5 XRAY PIN. NORMAL C561 , 1 MFD , C809 , 1MFD , C853 , 100MFD , C854 , 47MFD
28A1 INT SND ( MICRO MUTES SND. ) 1000MFD 5V RAIL
28A2 NO COLOR MAY GOES TO GREEN ,WHEN COL TURNED UP C613 0.01 CERAMIC
28W2 NO SND C2428 O.01 CERAMIC ON " C " BOARD
28X1 ALPHA 4H
28X1 ALPHA4H
28X1DP ALPHA 4
28X1DP ALPHA4 GOTO ALPHA4
33A1 INT SND C1206 - 1000MFD ( DECOUPLES 5V RAIL )
AC1 INT SHUTS DOWN AFT SW ON WITH LED FLASHING C857 470µ 25V IN RELAY SUPPLY
AEDP224), LOPTR(Q551 (BU2508DFLB), D558(RS3FS),C564 (.0039 1K2V)C565 (.0012 2KV)
ALPHA
ALPHA 2W)DEAD CEPT CHANNEL NUMBER Q551 D854 R564 R567 C808(10UF63V)IC801(STR54041M)
ALPHA BLANK RASTER/NO SND, R149(33R) ON IF PANEL.
ALPHA D854+STR54041+R556+R851+TDA3653C
ALPHA DEAD 2W STR45051 D854 R815(5R6) C808.
ALPHA NO PIC/LO BRILL C309(10UF50V) FROM TDA3505 PIN 20.
ALPHA1
ALPHA1 BLANK RASTER - NO IF NOISE TDA4505M-N3 JUNGLE CHIP
ALPHA1 BLANK RASTER NO SND, STBY LED ON IC1203 MICRO MAB8461PT134 - NO SDA DATA PIN 2 & PULL UP ONLY1.3V - LIFTING PIN RESTORED 4.8V
ALPHA1 BLANK RASTER TDA4505M ,MOD KIT
ALPHA1 BLOWS LINE TRANSISTOR LINE DRIVER TX DRY JOINTED
ALPHA1 COLOR - FLASHING BRIGHT BLUE. IC801.
ALPHA1 D854 HI HT 120VN(156V=25")SR2KN CAUSE STR54041+C808(10UF50V) IN CORNER.
ALPHA1 DARK DEFOCUSSED BARS MOVING DOWN, CRT FAULTY - MINIMISE BY ADJ OF A1S
ALPHA1 DARK HUMBAR, OK WHEN WARM ,CRT AGED INCREASE HEATER VOLTAGE
ALPHA1 DEAD 2SD14441 LOPTR R567 1 AMP FUSE D854 R2KL , C808 10UFD,HI HT
ALPHA1 DEAD 2SD965R STANDBY SWITCHING TRANSISTOR Q802 .
ALPHA1 DEAD 310V OK TRY SHORTING OUT PINS 3/4 OF OPTOCOUPLER D811 (ON3105TV)
ALPHA1 DEAD 310V OK, D851
ALPHA1 DEAD DIGITS OK, GOOD 320V NO HT STR54041(116VN).
ALPHA1 DEAD DISPLAY ONLY Q801 &Q802 2SD956/R
ALPHA1 DEAD FUSE OK. IC801 STR54041M CHOPPER CONTROL IC.
ALPHA1 DEAD LOPTR Q551 LINE DRIVER TRANSFORMER T531 PINS
ALPHA1 DEAD LOPTX
ALPHA1 DEAD NO EHT R567(TSF19192)/LOPTX/2SD1439/2SD1441/BU508A+47R+DTLF15505F/HR7265.
ALPHA1 DEAD NO PSU OUTPUT D851 HT RECT C2408M
ALPHA1 DEAD Q801/802 2SD965/R .
ALPHA1 DEAD Q802 2SD965R STBY SW TR IN PSU
ALPHA1 DEAD Q802 SBY SWITCH 2SD965R
ALPHA1 DEAD Q802(2SD965R) IN PSU.
ALPHA1 DEAD R1283(630)+IC1204(5V REG) NO STBY LINE
ALPHA1 DEAD R567(FUSIBLE 1A TSF19102)+LINEDRVTX ETH1953AY
ALPHA1 DEAD R802 4R7,5W STR54041M 2SD965 Q801/2 D854 C809 0.1UF C808 10UF.
ALPHA1 DEAD R851 2R2 NO LINE DRIVE TDA4505M-N3 JUNGLE CHIP (MUST BE CORRECT SUFFIX)
ALPHA1 DEAD SQUEALING PSU D854+LDRIVER TX.
ALPHA1 DEAD SR2KN D854 STR5041M IC801,OR C808 10UF, 50V
ALPHA1 DEAD STR54041 Q801 & Q802 (BOTH 2SD965). C808 (10UF 50V)
ALPHA1 DEAD STR54041M
ALPHA1 DEAD WHISTLE LOPTR(2SD1441/BU508A+47R+D),LOPTX(TLF15505F/HR7265)+R567(1A TSF19102)
ALPHA1 DEAD WITH PSU SQUEALING LINE DR TR - DRIVER TFMR FAULTY DUE TO ARCING BETWEEN HEATSINK LUGS & PRINT BY DRIVER TFMR
ALPHA1 DEAD/INT START UP - CHAN DISPLAY ONLY HT TO STR54041
ALPHA1 DEAD/WHISTLE LOPTR(2SD1441/BU508A+47R)+LINEDRVTX PINS
ALPHA1 FIELD - TXT LINES AT TOP OF PIC C455 100UF35V HI ESR
ALPHA1 FIELD HEIGHT REDUCED TO 1 INCH IC451 TDA3653A, C554 10UF250V
ALPHA1 FLASHES 1 COL BRIGHTLY THEN OFF WITH SQUEAL COIL ON CRT BASE
ALPHA1 GREY SCALE POOR WITH WEAK BLUE D306 ON B O/P FROM DECODER - USED 1N4148
ALPHA1 HIGH HT (128 INSTEAD OF 119V) C808 10UF50V
ALPHA1 INT FLICKS OFF TUNE WITH FLASH OF BLUE RASTER CHOPPER CHIP IC801
ALPHA1 INTERMITTENT TUNE CHOPTX PINS
ALPHA1 LACK OF COL AT TOP OF PIC WHILST PLAYING PRE-RECS CHANGE C604 TO 0U33F
ALPHA1 LINE FOLDOVER LINE DRIVER TX+/BU508A/2SD1441+47R LOPTX.
ALPHA1 LINES WITH WHISTLE C808 10UF63V
ALPHA1 LO HEIGHT - LIN OK FIT 3R3 RESISTOR ACROSS R461 TO INCREASE HEIGHT
ALPHA1 LO WIDTH ON BRIGHT PIC,STR54041,C808
ALPHA1 LOPTR 2SD1439+CP567+LINE DRIVER TX.
ALPHA1 LOPTR Q551 INT BLOWS CHECK DRY JOINTS LINE DR TRFMR & R567 1A FUSIBLE RESISTOR
ALPHA1 M51320P REMOVE AND SHORT IN/OUT .
ALPHA1 NO COL REPLACE SUB CARRIER TRIMMER AND ADJ; CHECK PAL DELAY LINE BY SUBST
ALPHA1 NO PIC/SND - CHAN IND LIT, PSU WHINING C808 , R567 PT NO TSF19102 (FUSE) - USED 1.4A WICKMAN
ALPHA1 NO PIC/SND M51320P AV SW IC2601
ALPHA1 NO SND OR PIC - SQUEALING. LINE DRIVE TRANSFORMER.
ALPHA1 NO SND/PIC OFF AIR OR VIA SCART IC2601 M51320P AV SW CHIP - TO CHECK, REMOVE CHIP & JUMPER I/P & O/P PINS
ALPHA1 PIC BRIGHTENS & DROPS WITH DIST FIELD SCAN WHEN HEATED SCAN COILS FAULTY - REQS REPLACEMENT OF CRT AS THEY ARE BONDED
ALPHA1 PIC GOES IN FROM RH SIDE WITH BLACK LINE ACROSS CENTRE FIELD O/P CHIP
ALPHA1 PLAIN BLANK RASTER & NO SND , NO OSD SYNC - OK VIA REAR SOCKETS. IC101 ( TDA4505M ) IN SIDE CAN MIDDLE OF .
ALPHA1 Q551 KEEPS BLOWING CHECK DRY-JOINTS ON LINE OUTPUT TRANSFORMER
ALPHA1 RASTER - BLANKING OUT. IC801.
ALPHA1 REDUCED TOP FRAME AFTER A FEW MINUTES. SCAN COILS
ALPHA1 REMOTE COMMANDS INT IGNORED DRY JOINT X3505 XTAL ON TXT PCB
ALPHA1 SCREAMS HT=20V LOPTR 2SD1439 LEAKY CP567 1A CCT PROT
ALPHA1 SNOWY PIC TUNER UNIT U344
ALPHA1 SQUEALING. LINE DRIVE TRANSFORMER.
ALPHA1 STBY TLF15506F LINE OUTPUT TRANSFORMER.
ALPHA1 STR54041
ALPHA1 TDA4505M-N3 USE CHEAPER TDA4505E IF R113 CHANGED FROM 22K TO 270K, R112 FROM 1M2 TO 470K & RE-ALIGN AFC COIL
ALPHA1 TDA4505M-N3 REPLACEMENT BY TDA4505E CHANGE R113 FROM 22K TO 470K; R112 1M5 TO 470K & RE-ALIGN AFC AS NEC
ALPHA1 TOP COLOUR MISSING ON VIDEO PB C604(0.33UF).
ALPHA1 TOP FOLDOVER LINES FIELD O/P CHIP PINS
ALPHA1 TOP PIC NO COLOR , INCREASE C604(0U33F)
ALPHA1 TRIPPING D854 SR2KN AVALANCHE DIODE DUE TO C808 10µ 50V STR54041M CHOPPER CHIP
ALPHA1 TRIPPING WITH FIELD COLLAPSE R7000 180K & R7005 150K START UP RES ON SIDE PANEL
ALPHA1 TUNING - DRIFT. IC801.
ALPHA1 TX2482 LINE FOLDOVER THEN DEAD WITH LOPTR 2SD1441 CHECK FOR DRY JOINTS LINE DR TRFMR & LOPTX
ALPHA1 VIDEO PB TOP PULLING CHANGE C604 FROM 0.047UF TO 0.33UF,
ALPHA1 WHISTLE/LINE HOLD WHEN HOT C808 10UF63V.
ALPHA1 WHISTLING D854 (RM2) C808 10MFD 63V IN PSU REPLACE RM2
ALPHA1W CHAN IND LIT WITH WHISTLE & NOTHING ELSE NO LINE DRIVE TRACED TO IC101 TDA4505-M1 JUNGLE CHIP
ALPHA1W COGGING ON VERTS C808 10UF50V
ALPHA1W COLD LINES C608 10UF, 63V
ALPHA1W DEAD D885 WAS OPEN CIRCUIT.
ALPHA1W DEAD DIGITS OK, TDA4505-M1 JUNGLE CHIP. IC101.
ALPHA1W DEAD DIGITS OK,320V OK,560K R803 STR54041M C808 10UF, 63V
ALPHA1W DEAD DIGITS OK,320V OK,LO HT(20V)STR54041M+C808(10UF63V)R803(560K).
ALPHA1W DEAD NO 12V SUPPLY TO LINE OSC PIN 7 IC101 FROM 12V REG IC851 - D855
ALPHA1W DEAD TLF15505F+ETH1953AY+2SD1441/(BU508A+47R)+R567(TSF19102) 1A FUSIBLE.
ALPHA1W DEADISH NO EHT R567/LOPTX/2SD1439/2SD1441 TLF15505F=HR7265
ALPHA1W FIELD COLLAPSE TDA4505M FAULTY - USE TDA4505E & CHANGE R112 FROM 1M5 TO 470K & R113 FROM 22K TO 470K
ALPHA1W FIELD COLLAPSE,TDA3654,C455(100UF)
ALPHA1W GOOD 320V NO CHOPPER O/P D854 ZENNER+ STR54041.
ALPHA1W LO HT (18V) LOPTR(2SD1441/BU508A+47R) READ 1200R, LOPTX OVERHEATS.
ALPHA1W LOUD WINE BUT NO PIC. R851 ( 1.2R FUSIBLE ) GO'S HIGH.
ALPHA1W NO COLOR TDA3562A
ALPHA1W NO SND BLANK RASTER,TDA4505M OR TDA4505N1 NOT "E".
ALPHA1W NO SND OR PIC - SQUEALING FROM PSU. D854 , IF STILL NO GOOD SUSPECT LOPTX.
ALPHA1W NO STBY SND MUTES BUT PIC ON, R817(47K) SEE TV JULY98.
ALPHA1W REMOVE TELETEXT PCB AND LINK ACROSS PINS 4 AND 6 OF PLUG E10 TO RESTORE PICTURE TX2472 INT SYNC/PIC CRYSTAL X3505
ALPHA1W SND DISTORT C2401
ALPHA1W TDA4505M=TDA4505N1 BUT NOT TDA4505E (GIVES PIC BUT NO TUNING).
ALPHA2
ALPHA2
ALPHA2 SEE TV MAG JULY 1997 + DEC 1998
ALPHA2 PIC INT DISAPPEARS OR ALMOST DISAPPEARS TO LEAVE BLACK SCREEN C626 10NF 50V CERAMIC CAP PIN 19 TDA3505
ALPHA2 TX21V1.HT=117VN TX2T1,TC21R1, TX25T2=155VN
ALPHA2 90 DEGREE 1989-1994 CCT DIA OF PSU TV MAG JULY 1997.
ALPHA2 AFTER 1HR TEXT FLASHES ON SCREEN . TEXT LOSES SYNC C3511 10NF
ALPHA2 AFTER 4HRS R567 BLOWS AND Q551 VERY HOT C502 DRY JOINTED
ALPHA2 ANALOGUE BARS NOT LOCKED - PIC OK C3511 220PF CONNECTED TO PIN 24 PULSE GEN CHIP ON TXT PANEL LEAKY
ALPHA2 BAD TEXT,C3511(220UF) IN THE 6MZH PHASE CONTROL CIRCUIT
ALPHA2 BLACK LINE ON RH SIDE OF PIC CHECK DRY JOINTS LINE DR TRFMR BEFORE LOPTR BITES DUST
ALPHA2 BLANK RASTER - NO TUNING C2612 10UF NON POL CAP DRY JOINTS AT PIN 5 IC2601 TV/AV SW IC
ALPHA2 BLANK RASTER, NO SND & UNLOCKED CHAN NO NO 12V ON A PANEL DUE TO R2420 0R68
ALPHA2 BLANK RASTER/FLYBACK A1S POT OR MAB8461PW135 MICROPRO ON TEXT PCB.
ALPHA2 BLANK WITH OSD R170(56R) 9V FEED TO IC101.
ALPHA2 BLOWS LINE TRANSISTOR LINE DRIVER TX DRY JOINTED
ALPHA2 BLUE DISAPPEARS AFTER HALF AN HOUR C612 0.01UF ON PIN 5 IC601
ALPHA2 BRIGHT RED FLYBACK LINES,OFF, SMALL COIL ON CRT BASE PCB
ALPHA2 BURSTS INTO LIFE THEN GOES INTO STBY LEAVING 3 L303 ( 10UH ) IN 12V CIRCUIT
ALPHA2 CHAN DISPLAY ONLY D851 LEAKY IN SECONDARY OF PSU
ALPHA2 CHAN IND OK NO PIC/SND,D851 .
ALPHA2 CHROMA BUT NO LUMA REPLACE TDA4565 CTI CHIP
ALPHA2 CHROMA UNLOCKED C642(10NF).
ALPHA2 COL SMEARING (RED IN THIS CASE) L353 ON CRT BASE CRACKED
ALPHA2 COLD NO SYNC C3550 1UF, NON-POLARISED CAPACITOR ON TEXT PCB
ALPHA2 COLD SNOWY C15. 2.2UF
ALPHA2 COLOR ERRATIC,C612 0.01UF.
ALPHA2 COLOR INT OFF & CHANGES HUE C612 0U01 PIN 5 IC601 LEAKY OR C642 LEAKY
ALPHA2 COLOR RED/GREEN BARS RUN C642 10NF ( TO SET OSC. SHORT PIN 11 OF IC601 TO AND ADJ. TRIMMER )
ALPHA2 COLOR VARIES C612(0.02UF).
ALPHA2 CONTRAST - POOR. R562 (130K) .
ALPHA2 CONTRAST WEAK R562 130K IN BEAM CURRENT LIM
ALPHA2 DARK SCN TDA3505+C311(0U47F50V)+C626(10NF).
ALPHA2 DEAD - NO LINE DRIVE R851 2R2 IN LINE DR TR SUPPLY
ALPHA2 DEAD D851
ALPHA2 DEAD AFT 20 MINS OK IF PINS 3 & 4 OF OPTO LINKED - D811 ON3105 OPTO COUPLER FAULTY
ALPHA2 DEAD AFT 4HRS WITH LOPTR OVERHEATED R567 IN LOP - C502 IN LINE OSC STAGE DRY JOINT
ALPHA2 DEAD CEPT CHAN DIGITS 320V OK, INT NO HT, STR54041, CHOPTX PINS
ALPHA2 DEAD D851(C2408M)
ALPHA2 DEAD D854 & R815 ( 5R6 ) OVER VOLTS DIODE
ALPHA2 DEAD D854, IC801,D854,D807,R815,C808,2SD1441RL/BU508A+47R LOPTR Q551,
ALPHA2 DEAD D854+C808(10UF50V) IN CORNER.
ALPHA2 DEAD DIGITS LIT, STR54041.
ALPHA2 DEAD EHT SURGE, R810(3R3) .
ALPHA2 DEAD FUSE BLOWN BLACK C807(100UF400V).
ALPHA2 DEAD LO HT, NOISY PSU, BU508A/2SD1441+47R LOPTR.
ALPHA2 DEAD LOPTR 2SD1441 R567 1A ,R851 1R2 1/2W ,C855 100UF35V,C808 10UF50V
ALPHA2 DEAD LOPTR(2SD1441RL/BU508A+47R ) R567 SR2KL D854 IC801 STR54041M.
ALPHA2 DEAD LOPTR+LOPTX(TLF15542F/HR7827)+R567+STR54041+D851.
ALPHA2 DEAD NO OUTPUT FROM PSU SUSPECT IC801 STR51424M
ALPHA2 DEAD NO POWER SUPPLY OPERATION D851 SC
ALPHA2 DEAD SET SQUEALS LINE OP TRANSISTOR SC FEED RESISTOR OC CAUSED BY DRY JOINTS ON LINE DRIVER TX
ALPHA2 DEAD SQUEAL LOPTR LEAKY(2SD1439/2SD1441)
ALPHA2 DEAD STBY LED FLICKERS AT SWITCH ON C882 0.01UF CERAMIC
ALPHA2 DEAD WHISTLE D854 +IC801+D807+R815+C808 +Q551(2SD1441RL).
ALPHA2 DEAD WHISTLE LOPTR 2SD1439(BU508A+68R+1N4007)+1R FUSIBLE.
ALPHA2 DEAD WHISTLE PSU D854 AVALANCHE DIODE CHOPPER CHIP IC801, D854 D807, R815, C808.- LOPTR Q551 2SD1441RL
ALPHA2 DEAD WITH WHINE - CHAN NO. SHOWING LOPTR 2SD1439 LEAKY - USED BU508D - RESOLD LINE DR TFMR
ALPHA2 DEAD. D851 (C2408M)
ALPHA2 EW BENT SIDES ,YELLOW CAP C754 180PF
ALPHA2 EW DIST C754 180PF IN EW PARABOLA CCT
ALPHA2 EW HOT BOWING EDGES C754(180PF).
ALPHA2 EW INT C754 180PF
ALPHA2 EW RASTER C754(180PF),L752
ALPHA2 FAINT LINE DOWN RHS C858(1000UF25V).
ALPHA2 FIELD - HOR LINES/PAIRING R469 470R
ALPHA2 FIELD - TOP FOLDOVER AN5521 FOP CHIP
ALPHA2 FIELD AN5521 MOD KIT TXS3EH001 .
ALPHA2 FIELD AN5521,R484,D451,L451,C403,R452,TDA2579A.
ALPHA2 FIELD COLLAPSE 0.01UF, CAPACITOR, C403.
ALPHA2 FIELD COLLAPSE AN5521 +C455(100UF50V)
ALPHA2 FIELD COLLAPSE AN5521 FOP CHIP - SHOULD BE 25V. R484 800MA FUSE
ALPHA2 FIELD COLLAPSE C400
ALPHA2 FIELD COLLAPSE C403 10NF CONNECTED TO PIN 2 TDA2579 TIMEBASE CHIP
ALPHA2 FIELD COLLAPSE C403(1NF) FROM PIN2/TDA2579A.
ALPHA2 FIELD COLLAPSE NO 25V ON PIN 3 AN5521 R848 800MA FUSE(BEHIND FIELD OP IC )
ALPHA2 FIELD COLLAPSE R484 REPLACE WITH CP N25
ALPHA2 FIELD COLLAPSE R484 FUSIBLE - USED 1R5 1/8W
ALPHA2 FIELD COLLAPSE TDA2579A AND C403 ( 0.01MFD ) PIN 2
ALPHA2 FIELD COLLAPSE WITH BLANKED OUT PIC C403 10NF PIN 2 TDA2579
ALPHA2 FIELD COLLAPSE, AN5521 R848 800MA CERAMIC FUSE.
ALPHA2 FIELD COLLAPSE.C403, CONNECTED TO PIN 2 OF THE TDA2579 TIMEBASE
ALPHA2 FIELD LO 25V R848(800MA)
ALPHA2 FIELD R469(160R) FIELD COIL DAMPING.
ALPHA2 FIZZ LO WIDTH LOPTR(2SD1441RL/BU508A+47R) R567(TSF19102)SOLDER LINE DRVTX
ALPHA2 GOES TO STBY 1 SEC AFTER SW ON NO 12V AS L303 10UH IN 12V FEED
ALPHA2 HIGH PITCHED WHISTLE - PIC OK. DRYS ON LOPTX OVERWINDING.
ALPHA2 HOT FLOATING OSD, C3511, 10NF CERAMIC CAPACITOR.
ALPHA2 HOT SND MUTED+NO CONTROLS IC1202.
ALPHA2 HOT TUNER DRIFT R171 10K
ALPHA2 INT BLACK LINES RHS, LINE DRV TX PINS T531.
ALPHA2 INT COLOR + POOR COLOR AT MAX SETTING OF COL. CO DL601 DELAY LINE
ALPHA2 INT COLOR/SATURATION, DL601.
ALPHA2 INT FLASHING AND GOING OFF AQUADAG EARTHING AND FIXING BOLTS ( REMOVE Q802 TO PREVENT SET SWITCHING OFF )
ALPHA2 INT FLASHING WITH SPECKLES & GOING OFF CHECK CRT FIXING BOLTS TO AQUADAG
ALPHA2 INT FUSE BLOWING C807 100UF, 400V.
ALPHA2 INT LOSS LINE HOLD LOPT DRY JOINTED
ALPHA2 INT MAINS FUSE F801 BLOWING MAINS SMOOTHER CAP C807 100µ 400V
ALPHA2 INT NO PIC ,REMOVE Q802 IN PSU TO STOP TRIP. LOPTX ARCING
ALPHA2 INT NO PIC C626(10NF50V).
ALPHA2 INT NO START R854 ( 0.47 ) CHANGE TO 0.33 PT. NO. ERQ1CKTR33S
ALPHA2 INT NOISE, LOPTX PINS
ALPHA2 INT ODD COLOR C612(10NF) FROM IC601/5
ALPHA2 INT OR WEAK COLOR DL601 CHROMA DELAY LINE
ALPHA2 INT PIC CHECK FOR DRY JOINTS CONNECTORR B4 (AT FRONT OF UNDER CRT RIM)
ALPHA2 INT PIC, M51326P SCART SWITCHING CHIP IC2601.LINK PINS 5 12.
ALPHA2 INT RED C353 220PF
ALPHA2 INT SYNC TTEXT C3517(10NF).
ALPHA2 INT VIDEO TVSM31326P AV/TV SWITCHER IC2601.
ALPHA2 INT VIDEO/AV TVSM1326P IC2601.
ALPHA2 INT WHISTLES DRY JOINTS ON LOPT OVERWINDING
ALPHA2 LEFT HAND SND CHAN. DIST. C2442 CERAMIC ( C2441 FOR RH SIDE )
ALPHA2 LHS SND DISTORT, 100PF CERAMIC CAPACITOR C2442
ALPHA2 LINE DOWN RH SIDE OF SCREEN C858 1000UF25V BAD CONNECTION TO PCB
ALPHA2 LINE OP TRANSISTOR SC RESOLDER LINE DRIVER TX
ALPHA2 LINES ACROSS/WHISTLE STR50401
ALPHA2 LO HT,DIS COL/Q802(NR STBYTX IN PSU) DISABLES TRIP/STBY
ALPHA2 LOPTR R567 OC D854 SC IC801 STR54041M
ALPHA2 LOPTR 2SD1439 WITH INTERNAL (DIODE+25R) NOT S2000A3.
ALPHA2 LOPTR AGAIN LOPTX PINS TLF15542F/HR7827, H1953 R567(SOC1000/TSF19192)2SD1441/BU508A.
ALPHA2 LOPTR,FUSIBLE FEED RES RESOLDER LINE DRIVE TRANSFORMER PINS
ALPHA2 LOSS OF LINE HOLD INT D/J AROUND LOPT ( T551 )
ALPHA2 LOSS OF SYNC, SCREEN BLANK IC501 TDA2579A
ALPHA2 NO ANALOGUE BARS OR TXT EXCEPT IN MIX C3526 10NF CERAMIC CAP LEAKY IN TXT CONTRAST CCT
ALPHA2 NO FOCUS - LOOKS LIKE CRT. . BLUE CHOKE. ON CRT BASE
ALPHA2 NO LUMINANCE TDA4565 CTI CHIP ON SUBPANEL
ALPHA2 NO NICAM SND OR DISPLAY FOR NICAM/MONO SND 6.55MHZ OSC NOT OSCILLATING. C2549 0µ01 CONNECTED TO PIN 9 IC2502
ALPHA2 NO PIC BECAUSE THE BRIGHTNESS CONTROL VOLTAGE THE DECOUPLING CAPACITOR C309 ( LOUF , 50V ) WAS LEAKY.
ALPHA2 NO PIC LED DIGITS OK,STBY Q802(2SD965R) IN PSU NR 4R7 7W.
ALPHA2 NO PIC NO BRIGHTNESS CONTROL VOLTS PIN 20 TDA3505 IC602; C309 10µ 50V LEAKY
ALPHA2 NO PIC NO CRT HEATERS LOPTX PINS 7 AND 10
ALPHA2 NO SND IC253 C269(10NF)
ALPHA2 NO SND C269(10NF50V) FROM IC253/2
ALPHA2 NO SND FOR 10MINS THEN OK C1206 ( 1 , 000UF ) 5V RESERVOIR CAP
ALPHA2 NO SND FOR FIRST 10 MINS C1206 1000µ 16V IN STBY 5V CCT
ALPHA2 NO SND OR CONTROL WHEN HEATED IC1202 MEMORY CHIP PCD8582P
ALPHA2 NO SND/PIC - CHAN NO. LIT Q551 2SD1441RL ; FUSIBLE LINK R567 TSF19102 LINE DR TFMR T531
ALPHA2 NO SND/VIS - CHAN NO. DISPLAYED STR54041-M U/S - FIT PROPER TYPE WITH SUFFIX OR WON'T WORK
ALPHA2 NO SYNC TDA2579A LINE GENERATOR/SYNC CHIP IC501
ALPHA2 NO SYNC C3550 1UF, NON-POLARISED CAPACITOR ON THE TEXT PANEL
ALPHA2 NO SYNC TDA2579A+C3550 1UF50V.
ALPHA2 NO SYNC/BLANK PIC/SHUTDOWN, IC501.
ALPHA2 NO TEXT C3517(10NF) FROM IC3501/15
ALPHA2 NO TEXT OK IN MIX NO BAR GRAPHS C3526 ( 10NF ) DECOUPLES TDA3505
ALPHA2 NO TEXT/MIXED OK, C3526 10NF
ALPHA2 NO VIDEO,TDA3505,C627,C626,C311,R562(130K).
ALPHA2 NO/DARK PIC C309(10UF50V).
ALPHA2 NO/INT COLOR TDA4510/TDA3505,C612(10NF LEAKY),C462(10NF).
ALPHA2 NO/POOR CONTRAST R562(130K) IC602(TDA3505).
ALPHA2 NOISY PSU, LOPTR BU508A+47R/2SD1441, LINE DRV TX (H1953)PINS
ALPHA2 ODD FIELD LINES R469 150R OR 180R.
ALPHA2 ODD FIELD,R469. 470R
ALPHA2 ONE COLOR MISSING,C351/352/353(220PF) LEAKY.
ALPHA2 OSD & BAR GRAPHS UNLOCKED TEXT ERRATIC C3511 ( 220NF ) PIN 24 IC3501 OR C3517 ( 0.01UF )
ALPHA2 OSD UNSTABLE C3511(220PF) ON TEXT PCB.
ALPHA2 PIC BOWED IN FROM SIDES. SMALL YELLOW C754 ( 180PF ) CONNECTED TO BASE OF Q751.
ALPHA2 PIC GOES OFF INT, C626(10NF)+C311.
ALPHA2 PIC GOES RED USUALLY D/J ON CRT BASE BUT CHECK C353 220PF LEAKY
ALPHA2 PIC LOOKS OFF TUNE IC101 DEMODULATOR COIL SHORTED TURNS
ALPHA2 POOR BLUE , CAP BETWEEN PIN 5 OF THE TDA4510 CHIP AND THE 12V SUPPLY
ALPHA2 POOR CONTRAST R562 ( 130K ) OPEN
ALPHA2 POOR EW L752 SC
ALPHA2 POOR PIC R562(130K) BEAM LIMITER.
ALPHA2 POOR SYNC WHEN COLD C3550 1UF NON POLAR.
ALPHA2 POOR TEXT PERFORMANCE C3507 100PF PIN 9 IC3501
ALPHA2 Q552 ( 2SD1441 ) CHECK FOR D/J ON LINE DRIVE TX T531
ALPHA2 R567(1000) FUSIBLE+ETH1953AY+TLF15534F+2SD1439.
ALPHA2 RED CONTENT SMEARY & CRITICAL TO SET PEAKING COIL IN RED O/P CCT
ALPHA2 RED PIC AFT SHORT WHILE OF OPERATION C353 220PF ON CRT BASE LEAKY
ALPHA2 RED SCRN LITTLE BLUE COIL NEXT TO RED O/P TRANSISTOR.
ALPHA2 RED/GREEN/BLUE 2SC2923RL + C351
ALPHA2 REFERENCE OSCILLATOR BARS ACROSS SCREEN. C642 ( 10NF ) LEAKY.
ALPHA2 RHS PULLING LOPTX PINS.
ALPHA2 SERVICING THE ALPHA2 SEE TV MAG JULY 1997 & DEC 1998
ALPHA2 SEVERE FIELD DISTORTION R469 470R
ALPHA2 SHUTS DOWN WHEN WARM ON3105 D811 OPTOCOUPLER ( LINK PINS 3 AND 4 TOGETHER TO PROVE )
ALPHA2 SLOW/INT START/NOISY PSU,STR54041,C808(10UF50V)
ALPHA2 SND DIST FROM 1 CHAN C2442/1 100PF LEAKY
ALPHA2 SND HOT NO SND IC1202(PCD8582P)
ALPHA2 SND MUTE, C1206 ON THE MAIN BOARD.
ALPHA2 SND ON LEFT/RIGHT DISTORTED C2442/2441 LEAKY(100PF).
ALPHA2 SND, AN5265 18VPIN9 R28(12R),C272(470UF25V),C2442 LEAKY.
ALPHA2 SND, IC253 12V PIN1 R221(56R),C269(10NF), IC253 PIN2=5V.
ALPHA2 STBY IN THE RESET LINE TO MICRO. REMOVE R8 , C1251 10NF
ALPHA2 STRIATIONS R469(470R).
ALPHA2 SYNC TDA2579A,R572(68K),C507(4U7F50V),C3550(1UF50VNONPOL)ON TEXTPANEL.
ALPHA2 TELETEXT - WHITE BARS OVER TELETEXT MOD
ALPHA2 TEXT INT DISPLAYS C3511(220PF).
ALPHA2 TUNER AGC=3-4V PIN 4,12V PIN 7,5V PINS10,12, C117,R135 POT.
ALPHA2 TUNER DRIFT INT C15(2U2F)
ALPHA2 TUNING ERRATIC & CHANS DISAPPEAR C15 2µ2
ALPHA2 TUNING GOES OFF WITH TICKING CHOPPER CHIP STR54041
ALPHA2 TUNING INT R171 10K IN TUNING VOLTAGE LINE INT
ALPHA2 TUNING SAB3035 IC171.
ALPHA2 TUNING/AFC COIL AT PINS 22 AND 23
ALPHA2 TXT ABSENT C3517 10NF PIN 15 IC3501 LEAKY
ALPHA2 TXT DRIFTS ACROSS PIC/FLASHING C3511 220PF IN 6MHZ PHASE CCT LEAKY
ALPHA2 UNLOCKED COLORS C642(10NF)
ALPHA2 UNLOCKED COLORS SHORT PIN 11 OF IC601 TO CHASSIS ADJUST TRIMMER, C637.
ALPHA2 UNLOCKED TEXT C3511(220PF)
ALPHA2 VIDEO DISAPPEARS INT SND OK LINK PINS 5 & 12 OF IC2601 IF PIC RETURNS IC U/S
ALPHA2 VIDEO INT DISAPPEARS IC2601 M51326P AV SW CHIP - TO CHECK, REMOVE CHIP & JUMPER I/P PIN 5 & O/P PIN12
ALPHA2 WARM STOPS,OK IF PINS 3 AND 4 OF THE ON3105 OPTO D811 LINKED
ALPHA2 WEAK CONTRAST R562(130K).
ALPHA2 WEIRD LINE TWINNING 220R ACROSS SCAN COILS BLUE/WHITE CURES.
ALPHA2 WHISTLING INT DRY JOINTS LOPTX OVERWIND
ALPHA2 WIDTH LO LINE DRIVER TX PINS .
ALPHA2A NOISE ON NICAM C2572 - C2573 220PF
ALPHA2A SMEARY VIDEO CHECK C684 ON V MODULE 22MFD BI-POLAR - USE 2 IN SERIES.
ALPHA2W
ALPHA2W HT=156VN
ALPHA2W BLOWING LINE TRANSISTORS. DRYS ON LINE DRIVER TRANSFORMER.
ALPHA2W COLD LINE ACROSS TOP PIC C455(100UF50V) NR IC.
ALPHA2W COLD NO SND, IC1204, 5V REGULATOR.
ALPHA2W DEAD R803 AND R827 ( 220K ) R815 ( 5R6 ) Q801 & Q802 & STR54041
ALPHA2W DEAD 155VN D854 R567,STR54041 LOPTR Q551, LOPTX
ALPHA2W DEAD 320V OK ,R803(560K)
ALPHA2W DEAD D851(C2408M).
ALPHA2W DEAD DIGIT OK, LOPTR Q551 D854 R567 C808 10UF63V STR54041M.
ALPHA2W DEAD DIGITS OK, IN PSU Q802. 2SD965R
ALPHA2W DEAD DIGITS OK,SHORT OPTO 3/4,DISCON LOPTX ,LO/NO HT,STR54041
ALPHA2W DEAD DISCON R1245 TO DISABLE STBY,D1315(MA700).
ALPHA2W DEAD EXCEPT CHAN IND Q551 LOPTR ; D854 OVER VOLTS ; R564 C808 10µF63V & IC801 STR54041M
ALPHA2W DEAD IC1204 (STBY 5V REG) OVERHEATS WITH ONLY 1V ON O/P ZENER D171 MA4082 , MICROPROCESSOR IC1203 MAB8461PW134 .
ALPHA2W DEAD LOPTR 2SD1441,R567 1A STR54041 CITAC CHIP SAB3035 CAUSING BLANK RASTER/NO SND VIA AERIAL OR AV
ALPHA2W DEAD LOPTR CAUSE DRIVER TX PINS.
ALPHA2W DEAD NO VOLTS PIN 2 IC801 CHOPPER; CHECK R803 & R827 220K
ALPHA2W DEAD PSU NOISE ,LOPTR(2SD1441) RESOLDER LINE DRV TX
ALPHA2W DEAD R815 5R6, Q801 Q802 STR54041
ALPHA2W DEAD WHISTLE R567/D854/LOPTR ,C808(10UF63V),STR54041M.
ALPHA2W DEAD WITH Q551 REPLACE C808
ALPHA2W DEAD,CHAN INDICATOR OK,LOPTX Q551 D854 R564 R567 C808(10UF63V)IC801(STR54041M)
ALPHA2W DEAD. R803 R827 220K
ALPHA2W E-W DIST L752 OR C754 180PF LEAKY IN BASE TO Q751
ALPHA2W EW CORRECTION WAS L752 BEING SHORT-CIRCUITED.
ALPHA2W FAINT LINE SHADING DOWN RIGHT HAND SIDE. C858(1000UF,25V )
ALPHA2W FIELD - HEIGHT TOP FOLDOVER R469 150R (UNDER WHITE CERAMIC RES BY LOPTX)
ALPHA2W FIELD COLLAPSE IC451(AN5521)+FUSIBLE FROM PIN3 (SOC800)+C455(100UF).
ALPHA2W FIELD COLLAPSE IC501 TDA2579A & CHECK C403 0µ01 PIN 2 IC FOR LEAK
ALPHA2W FIELD INSTABILITY R469 470R-150
ALPHA2W FIELD UNSTABLE R469 ACROSS SCAN COILS 220R. BLUE/WHITE WIRES
ALPHA2W FIELD WEIRD LINES 180R ACROSS SCANCOILS R569 UNDER LINEFEED W/WOUND.
ALPHA2W FIELD WEIRD LINES ACROSS ON PIC C455(100UF50V) NR IC.
ALPHA2W FLYBACK LINES,C455(100UF50V)
ALPHA2W FLYBACK LINES,IC451(AN5521)
ALPHA2W GOES BRIGHT RED THEN TRIPS OFF Q353 RED O/P TR COLL DROPS TO 3.5V - L353 180µH COIL
ALPHA2W HEIGHT/TOP FOLDOVER R469(150R) NR LOPTX.
ALPHA2W HOT RHS WIDTH, RESOLDER LINE DRV TX
ALPHA2W INT BRIGHT RED L353(180UH).
ALPHA2W INT HI RED, R353, 180UH PEAKING COIL L353
ALPHA2W INT LINE HOLD, LOPTX PINS
ALPHA2W LINES ON PIC & WHISTLE STR50401 - USE GENUINE REPLACEMENT
ALPHA2W LOPT TR, LINE DRIVE TX ( OFTEN INVISIBLE )
ALPHA2W LOPTR BU508A/2SD1441+R567+TLF15505F/HR7265+DRIVER TX ETH19Y53AY 154VN.
ALPHA2W LOPTR S/C BU508A/2SD1441+R567 LINE DRIVER TX.
ALPHA2W LOPTR(2SD1441)+LOPTX(TLF15542F/HR7827)+DRVTX(TH19Y53AY)+R567(TSF19102)+STR54041.
ALPHA2W LOPTR(2SD1441/BU508A) LOPTX PINS/WEAK DRIVE.
ALPHA2W LOPTR+R567 CAUSE C502
ALPHA2W LOUD WHISTLE STR50401 USE GENUINE TYPE.
ALPHA2W NO 12V TO BOARD-M L303(10UH)
ALPHA2W NO EW CORRECTION, L752.
ALPHA2W NO LUMA TDA4565 CTI CHIP ON ITS SUB-PANEL.
ALPHA2W NO PIC, ONLY BLANK RASTER L303 10UF ZENER D171, IC1204
ALPHA2W NO PIC,R390(120K) ON CRT BASE PCB
ALPHA2W NO SIGNALS - R/C FUNCTS SLOW TUNER FAULTY (PRESCALER FAULT)
ALPHA2W NO SND OR VISION - HEATERS & EHT PRESENT CHOKE L853 TLT030L119C ATTACHED TO 12V REG
ALPHA2W NON LIN TOP OF FIELD SCAN OR PORTION MISSING R469 UNDERNEATH R551 10R 7W - COULD BE EITHER 150R, 270R OR 470R 1W
ALPHA2W ONE BRIGHT COLOR,L351,L352,L353
ALPHA2W ONE COLOR HI, L351/2/3.
ALPHA2W PIC OBSCURED BY LINES & FIELD DIST R649 150R
ALPHA2W PIC PULLING TO RIGHT DRY JOINTS LINE DR TFMR
ALPHA2W POOR CONTRAST C626 10NF,
ALPHA2W POOR WASHED OUT PIC , NORMAL SND . C626 10NF - DECOUPLING PIN 19 TDA3505
ALPHA2W POWER SCREAM C808/R567.
ALPHA2W POWERS UP BUT SHUTS DOWN , L303
ALPHA2W PSU NOISE, HI HT C808(10UF63V) R567(1000 1A)
ALPHA2W PSU NOISE, LOPTR 2SD1441/BU508A Q551 R567 +LINE DRV TX PINS
ALPHA2W PULLING RHS, DRY JOINTS AT THE LINE DRIVER TRANSFORMER.
ALPHA2W RED SMEARY ANODE LOAD RESISTOR GONE HI.
ALPHA2W RED SMEARY, PEAKING COIL IN THE RED OUTPUT TRANSISTORS LOAD CIRCUIT
ALPHA2W RHS CRAMP HOT,LINE DRIVER TX PINS.
ALPHA2W RHS STRIATION C858 1,000UF, 25V
ALPHA2W RUNS FOR 2 SEC AND GOES DEAD HT TOO HIGH AT 180V, OK IF RUNNING ON A DUMMY LOAD- STR54041
ALPHA2W SCREAMING PSU ONLY HT 175V (158V) - R567(S1000),C808(10UF50V)
ALPHA2W SHADING LINE DOWN RHS C858(1000UF) PINS.
ALPHA2W SHORT SQUEEK LOPTR(2SD144RL)+ DRIVERTX PINS.
ALPHA2W SQUEALING. 2SD1441 , LINE DRIVER TRANSFORMER.
ALPHA2W STR54041M +R567(SOC1000)+D854+LOPTR 2SD1441
ALPHA2W SURGE/OFF L303 (10UH)
ALPHA2W WARM TUNER PROBLEMS R171.
ALPHA3
ALPHA3 TV MAG JUNE 97.
ALPHA3
ALPHA3 ALPHA3 SEE TV MAG MAR-JUN 1994
ALPHA3 FAULT NOTES: ALPHA3 SEE TV MAG JULY 1994
ALPHA3 AFTER 5MINS PIC + SND DISAPPEAR RESET C1251 10NF
ALPHA3 BAD TEXT, 220UF C3511 IN THE 6MZH PHASE CONTROL CIRCUIT
ALPHA3 BLACK DIAGONAL LINES ACROSS PIC - VERY INT D329 ZENER DIODE WAS LEAKY MA4068 - STABILISES SUPPLY TO TDA4670 IC302
ALPHA3 BLANK RASTER ,NO CTRLS, TEXT CHIPS
ALPHA3 BRIGHT FLYBACK LINES ACROSS TOP OF SCREEN - VERY INT FIT KIT TZSEN001 CONSISTING OF REPLACEMENT SCAN COIL AND FOP CHIP
ALPHA3 COLOR VARIES - BLUE CONTENT REDUCES - INT C352 330PF CERAMIC CAP DECOUPLING Q366 EMITTER
ALPHA3 DARK BLANK RASTER - NO SND. C1251 ( 10NF ) LEAKY , MAIN MICROCONTROLLER & MEMORY CHIPS.
ALPHA3 DARK BLANK RASTER ,NO SND - DIS SERIAL & CLOCK LINES TO TXT PANEL TO ELLIMINATE THIS CCT; IC3507 FAULTY (MAB8461PW13S)
ALPHA3 DARK PIC GETTING WORSE WITH TIME Q355 2SC3311 ON CRT BASE LEAKY (BLACK LEVEL REF)
ALPHA3 DEAD - BLOWS R822 4R7 5W & R555 LOP FUSIBLE LINE DRIVE WFM DIST - C501 0µ1CAP IN LINE OSC STAGE LEAKY
ALPHA3 DEAD - LOPTR LEAKY ALSO CHECK R567 1A FUSE FEEDING LOP STAGE FOR
ALPHA3 DEAD - R555 FUSIBLE RES IN LOP STAGE FEED LOPTX
ALPHA3 DEAD (INT) LED LIT C1251 10NF50V.
ALPHA3 DEAD APART FROM BUZZING NOISE R555 FUSIBLE RESISTOR OC IF EHT TOO HIGH AFTER REPLACING SUSPECT LOPT
ALPHA3 DEAD C822(0U01F).
ALPHA3 DEAD LED FLICKER C522(10NF) PSU SECONDARY.
ALPHA3 DEAD LOPTR+R555.
ALPHA3 DEAD NOISE,R555+LOPTX T551
ALPHA3 DEAD R555(SOC1000) CAUSE LOPTX(TLF15548F HR7294)
ALPHA3 DEAD R822, 4R7 10W R555 TDA2579A C501, 0.1UF
ALPHA3 DEAD STBY TRANSFORMER
ALPHA3 DEAD WITH LED FLICKERING AT SW ON Q823 CONDUCTING AS OPTO WAS TURNED ON; Q825 WAS SW ON BECAUSE C822 0µ01 CERAMIC CAP LEAKY
ALPHA3 DEAD, R555+LOPTR.
ALPHA3 DEAD. R555 HT FEED .
ALPHA3 DEAD/NO LINE DRIVE R555,LOPTX,EW DIODES.
ALPHA3 DEADISH LOPTX TLF15548F.
ALPHA3 DIAGONAL LINES ZENER DIODE, D329,MA4068.
ALPHA3 E-W BOWING WITH NO CONTROL EFFECT CHECK TDA8145 IC701 & R708 & L701 ALSO 0µ01 50V DECOUPLING CAP TO PIN 1 IC701
ALPHA3 FIELD COLLAPSE C400 10N 50V CONNECTED TO PIN 2 TDA2579A TBASE CHIP
ALPHA3 FIELD COLLAPSE C400(10NF50V).
ALPHA3 FIELD IC451 MOD KIT TZS5EN001 NEW SCAN COILS .
ALPHA3 GOES DARK WITH NO SND WHEN HEATED C1251 10NF WAS LEAKY IN MICRO RESET CCT
ALPHA3 GOES OFF AFT 3 HOURS - FLASHES & SHUTS DOWN CHECK HEATSINK CLIP ON IC891
ALPHA3 GREEN AND RED "GLITCHES" ACROSS , TEXT DISP C649 ( 120PF ) PIN 3 IC302 PIC TRANSIENT
ALPHA3 INT COLOUR BLUE C352 330PF
ALPHA3 INT DEAD C1251, 10NF, 50V CERAMIC
ALPHA3 INT DIAGONAL BLACK/WHITE STRIPES D329 ZENER PT NO MA4068
ALPHA3 INT FLYBACK KIT TZS5EN001
ALPHA3 INT LOSS OF SND & PIC DRY JOINTS PRESCALER CHIP INSIDE TUNER
ALPHA3 INT LOSS OF TUNING DRY JOINTS ON PRESCALER IC IN TUNER
ALPHA3 INT WARM NO PIC/SND, RESOLDER PR-SCALER CHIP IN TUNER
ALPHA3 LO BRILL Q355(2SC3311) ON CRT BASE PCB
ALPHA3 LOPTX HR7294/TLF15548F +R555(SOC1000) LOPTR(2SD1441 D+R)
ALPHA3 LOSS OF VIDEO & AUDIO SIGS LOOSE PANEL H DUE TO CUSTOMER PUSHING IN SCART LEADS
ALPHA3 NO COL WHEN USING AV CONNECTOR CHECK FRONT AV2 SOURCE SW IS NOT SET TO "S" POSN
ALPHA3 NO COLOR IC303 TDA3505 VID CONTROL CHIP PIN 16 WAS LOW INSTEAD OF 3V - C644 0µ01 CERAMIC DECOUPLER LEAKY
ALPHA3 NO COLOR PIN 16 TDA 3505 LOW ( NOT 3V ) C644 0.01UF SC
ALPHA3 NO COLOR REF OSC NOT WORKING; 0µ01 CERAMIC CAP CONNECTED TO PIN 14 IC601 DECODER CHIP LEAKY
ALPHA3 NO COLOUR 0.01UF ON PIN 14 OF DECODER.
ALPHA3 NO COLOUR. C644,
ALPHA3 NO G IN TXT D3309 - D3308 OR D3310 COULD CAUSE SAME PROBLEM WITH OTHER COLS
ALPHA3 NO REMOTE
ALPHA3 NO SND - DARK BLANK RASTER. C1251 ( 10NF ) LEAKY , MAIN MICROCONTROLLER & MEMORY CHIPS.
ALPHA3 NO TEXT C3517(10NF) FROM IC3501/15
ALPHA3 NO TUNING MEMORY CHIP SELECT SIGNAL FROM PIN 53 OF MICRO TO MEMORY CHIP MISSING - L1209
ALPHA3 NO TUNING MEMORY L1209 ELEXT100KA.
ALPHA3 NO TUNING MEMORY, L1209 O/C PT NOELEXT100KA.
ALPHA3 POOR FOCUS - ADJ FOCUS VARIES BRILL INTERNAL LEAK IN CRT BETWEEN A1 AND FOCUS ELECTRODES
ALPHA3 POOR FOCUS TUBE FAULTY.
ALPHA3 POOR FOCUS. FOCUS POT ACTS LIKE A1'S POT, CAUSE CRT
ALPHA3 POOR TEXT C3507 FROM PIN 9 OF IC3501, 100PF.
ALPHA3 POOR TEXT,C3511(220PF) ON H PCB,NR SAA5231
ALPHA3 R822 4R7 10W SURGE LIMITER BLOWN , C501 0.1UF
ALPHA3 RED & GREEN 'GLICHES' ACROSS SCREEN INT OK IN TXT MODE - C649 120PF FAULTY - PIN 3 IC302
ALPHA3 RED/GREEN FLASHES C649 120PF FROM IC302 PIN 3 AND CHASSIS.
ALPHA3 SAT C1251 (A DREADED 10NF CAP)
ALPHA3 STBY Q825 OPTO DRIVER HARD ON. R843 - C1251 10NF
ALPHA3 STBY REMOVING R843, SET WAS ABLE TO START-UP.10NF CAPACITOR, C1251.
ALPHA3 STBY. LOPTX
ALPHA3 TOP THIRD WHITE LINES, BOTTOM HALF GREEN, IC891
ALPHA3 TX25A2,
ALPHA3 TX28A2X E-W BOWING R751 33R
ALPHA3 TXT - NO PAGES BUT HEADER PRESENT OR JUMPING TXT C3511 220PF CERAMIC CAP ON TXT PANEL LEAKY
ALPHA3 TXT POOR WITH MISSING LINES & CORRUPT C3507 100PF LEAKY TO PIN 9 IC3501
ALPHA3 UNLOCKED TEXT C3511(220PF)
ALPHA3 WARM DARK BLANK RASTER C1251 10NF IN THE MICROCONTROLLER RE-SET
ALPHA4
ALPHA4
ALPHA4 BLANK RASTER - SND OK - SAME ON SCART; ON TXTSHOWS "P100" IC3002 (M52472P) ON THE "H" PANEL.
ALPHA4 BLANK SCREEN - OSD OK 9V SUPPLY TO IF PROC CHIP IC101 LOW AT PIN 41. R170 56R
ALPHA4 CHASSIS OSD BLACK BOXES C3304 0.01UF) R3309 HI .
ALPHA4 CRACKLE FROM LH SPEAKER R2081 10K SM CRACKED
ALPHA4 DEAD 320V OK,STR56041 WVE
ALPHA4 DEAD LO HT LOPTX
ALPHA4 DEAD LO HT(25V) STR56041
ALPHA4 DEAD LOPTX
ALPHA4 DEAD POWER SURGE,VDP3108-A-29(MOD KIT)
ALPHA4 DEAD STR56041M
ALPHA4 DEAD/STBY WHISTLE,LOPTR(2SD1577/BU2508AF) CAUSE HI HT/LINE DRV TX
ALPHA4 FIELD - HEIGHT INCREASES WHEN HEATED WITH TWITCHING C402 0µ33 MYLAR CAP LEAKY IN RAMP GEN CCT
ALPHA4 FIELD COLLAPSE ,SERVICE SWITCH NR AERIAL SOCKET
ALPHA4 FIELD CRAMPING,TDA3654
ALPHA4 FLASHING LINES ACROSS, TUNER UNIT
ALPHA4 INSIDE THE ALPHA4 SEE TV MAG JUNE - SEPT 1995
ALPHA4 INT LINES ACROSS PIC UHF TUNER FAULTY
ALPHA4 NO FRONT SPKRS C81 C83 2200UF+ LA4280
ALPHA4 NO PIC - SND OK R539 10 OHMS FUSE RESISTOR IN SUPPLY TO LINE DRIVER TRANSISTOR .
ALPHA4 NO SOUND FOR FRONT SPEAKERS C81/83/LA4280.
ALPHA4 NO SYNC TDA2579B
ALPHA4 ODD OSD, C3304 IS AN 0.01UF CERAMIC CAPACITOR
ALPHA4 OSD BLACK BOXES,TEXT OK, C3304 0.01UF R3309 820R
ALPHA4 OSD CONSIST OF BLACK BOXES ONLY - PIC & TXT OK C3304 0µ01 LEAKY & R3309 820R
ALPHA4 SHUTS DOWN AT SW ON WITH A SPLUTTER - HT ONLY 60V LOPTX
ALPHA4 STBY C565(1800PF3KV)
ALPHA4 STBY OVERIDE EARTH D826 OPTO
ALPHA4 STBY SHORT OPTO 3/4 TO TEST, Q890 LEAKY
ALPHA4 WARM EXCESS HEIGHT,C402 BROWN TYPE
ALPHA4 WON'T POWER UP - WORKS IF PINS 3 & 4 OF OPTO SHORTED Q890 2SC3311-R
ALPHA4 WORKED WITH PINS 3 AND 4 OF THE OPTOCOUPLER SHORTED, Q890 2SC3311-R,
ANUBIS B DEMO MODE SW ON MAINS WHILST DEPRESSING "VOL" & "PROG+" ON SET
C
CN516 DEAD - IN PROT MODE WHEN PROT MODE DISABLED, ONLY SCAN BOTTOM 1/3RD OF SCREEN DUE TO D412 27V ZENER MA4270H
CN516 DEAD WHEN PROT MODE DISABLED, ONLY SCAN BOTTOM 1/3RD, D412 27V ZENER MA4270H
CN677R BLOWS LOPTR AT SW ON LINE DR TFMR FAULTY - COULD BE DRY JOINTS ON IT
CN677R BLOWS LOPTRANSISTOR BU2508D SUBST FOR THE 2SD1175 FITTED SEEMS TO HAVE CURED IT
CN677R TUNE STORE INOP D1129
CRT PHOSPHOR BURN RELAY RL6101 ON FRONT PCB AND A NEW CRT R668
CT-T14R DEADC810 R610
CT1427R TV. R805(10K), R810(5R63W).
CT1427R TV.R805(10K), R810(5R6 ,3W).
CT20G12V DEAD STR58041 CHIP
CT20G3W1 R817(1R5 7W)
CT20G3W1 DEAD R801(1R5 7W)
CT20S U4 GOTO U4
CT20S U4 CHASSIS
CT22S U4W CHASSIS
CT27G30T AMEDP246 DEAD FUSE STK-730-020 LOPTR(BU2508DF/2SC5250). D558(RS3FS),C564 (.0039 1K2V)C565 (.0012 2KV)
CT27G30T DEAD FUSE. STK-730-020 ,LOPTR(BU2508DF / 2SC5250). D558 (RS3FS), C564 (.0039 1.2KV) C565 (.0012 2KV)
CT27S16CS 110V (142V) DEAD LOPTR
CT27SF12T TV CHASSIS AEDP248
CT32S20U CH. ANEDP275, PIC CUTOFF 1/4" ON RIGHT SIDE OF CRT,SMALL 160V CAPS IN THE HORZ SWEEP
CT9012A DEAD FUSE,DEGAUSS POSISTOR
CTM2066S FIELD COLLAPSE SCAN COILS
CTM2066S TV FIELD COLLAPSE,FOP CHIP
CTM209S, ALEDP203, IC001 MICROPROCESSOR PANASONIC# MN15151Q14R=$16.
CTN1956R ANDP201.IC001 MICROPROCESSOR PANASONIC# MN15151Q14R=$16.
CTN2061S DARK PIC, CRT
CTT14R DEAD C810 R610
EUR04 DEAD C869(100UF25V)
EURO 4)INT STBY C454(22NF SM), NR FIELD CHIP.
EURO1
EURO1
EURO1 PANASONIC'S DIGITAL TV SEE TV MAG JUL 1993, SEPT, OCT, NOV & DEC 1993
EURO1 SEE TV MAG OCT 1998
EURO1 SERVICE MODE1 IN SOUND-MENU LOW-TONE-REGEL TO MAX AND HIGH-TONE-REGEL TO MIN
EURO1 SERVICE MODE2 PRESS VOL- ON TV AND RESET ON RC, RED/GRN/YELL/BLUE ,STORE,SWITCH OFF
EURO1 SERVICING THE EURO-1 SEE TV MAG OCT 1998
EURO1 AV OK,SHUTS DOWN INT ON OFF-AIR SELECT= MSP2410-08 IC1401.
EURO1 BLACK LINES APPEAR IN TXT & OSD BOXES WHEN HEATED IC1501 DPU2553 DEFLECTION PROC CHIP
EURO1 BRIGTNESS INCREASES UNTIL A WHITE RASTER IS PRESENT DPU2553 DEFLECTION PROC CHIP
EURO1 COL INT OR ABSENT X1656 OSC XTAL
EURO1 COMES ON NO PIC/SND , THEN SBY R561 BECAUSE IC561 TDA8175 FIELD CHIP
EURO1 DARK AREAS OF PIC BECOME DOTTED - VERY INT IC1661 DT12223 FAULTY (TRANSIENT IMPROVEMENT CHIP)
EURO1 DARK BLANK RASTER NO SND NICAM CHIP IC1401 MSP2410
EURO1 DARK BLANK RASTER ACVP2205 HOT+SAD2140 IC1601.
EURO1 DARK BLANK RASTER SAD2140 S-VHS A2D CONVERTER CHIP IC1601.
EURO1 DARK DOTTED, IC1661, TYPE DTI2223,
EURO1 DARK PICTURE SAD2140 ANALOGUE-TO-DIGITAL CONVERTER CHIP IC1601
EURO1 DARK RASTER/ NO SND, REMOVE TO TEST THEN REPLACE MSP2410
EURO1 DEAD LEDS FLASH, F656,T528 LINE DRV
EURO1 DEAD POWER SURGE, R622, Q624 T639
EURO1 DEAD R628 470K PIN 5 OF THE TDA4601 CHOPPER CONTROL CHIP IC611
EURO1 DEAD STBY LED LIGHTS BRIEFLY AT SW ON ALL 4 ELECT CAPS IN PSU
EURO1 DEAD TDA4601+C622
EURO1 DISTORTED AUDIO FROM THE RIGHT CHANNEL
EURO1 EHT OK NO PIC/SND Q1011 2SC3940,4R7 R1102 0.1UFSM C1102.
EURO1 FIELD COLLAPSE IC561 TDA8175, C558 2200F 50V; C563 220F 50V
EURO1 FIELD COLLAPSE TDA8175 FIT A MA2100 DIODE IN LINK B51,CATHODE TO D562/R566.
EURO1 FIELD COLLAPSE TDA8175+C558(2200UF50V)+C563(220UF50V).
EURO1 FIELD COLLAPSE, TDA8175 IC611 FIT MA2100 DIODE IN PLACE OF LINK B51 - CATHODE TO D562 & R566 KIT PT NO TZ55EK001
EURO1 FIELD COLLAPSE. TDA8175 IC561 C588 2200UF50V, C563 220UF50V,
EURO1 FIELD KIT PART NO. TZ55EK001/TDA8175 TO TDA8177 SEME
EURO1 FIELD LO HEIGHT,TDA8175
EURO1 FIELD TOP COMPRESSION FOP CHIP TDA8175 IC611& FIT DIODE MOD
EURO1 FIELD TOP CRAMP TDA8175 IC561 MOD KIT TZS5EK001/TZS9EK026-1(TDA8177).
EURO1 FIELD TOP FOLDOVER IC561 TDA8175 FAILS DUE TO SPIKES - MOD KIT TZS5K002 (DIODE TO REPLACE LINK B51 & NEW IC)
EURO1 HALF FIELD COLLAPSE IC567 TDA8175.
EURO1 HOT CHROMA OSC OFF SPEED, DECODER
EURO1 INT BLANK RASTER SAD2140 VIDEO AD CONVERTER CHIP IC1601
EURO1 INT COLOR CRYSTAL X1656,
EURO1 INT DARK AREAS DOTTED IC1661, TYPE DTI22223,
EURO1 INT DEAD MPS2410-08 MULTI SOUND PROCESSOR CHIP IC1401 WAS PULLING ITS RESET
EURO1 INT DOTTED EFFECT IN AREAS OF DARK PIC IC1661 DT12223 ( TRANSIENT IMPROVEMENT CHIP )
EURO1 INT EW MCU2600 MASTER OSCILLATOR CHIP IC651.
EURO1 INT FIELD COLLAPSE R561(1R5) +TDA8175+C563(220UF35V).
EURO1 INT HEIGHT & WIDTH DRASTIC INCREASES MCU2600 IC651 MASTER OSC CHIP
EURO1 INT LOSS OF SIGNALS TUNER D/J INSIDE TUNER ON PRESCALER CHIP
EURO1 INT LOST SIGNALS TUNER FAULTY
EURO1 INT SHUTS DOWN IC1410-08.
EURO1 INT SIGNALS, TUNER UNIT
EURO1 INT WHITE SCRN TPU 2763 TELETEXT CHIP IC1761
EURO1 LIGHT RASTER/NO SYNC SAD2140 IC1601.
EURO1 LINE DRIVE CUTS OUT AFT 30 SECS - PIC & SND OK IN THIS PERIOD IF AERIAL DIS'D, SET WOULD WORK CONTINUALLY; IC1401 MSP2410 NICAM CHIP
EURO1 LINE PAIRING AT BOTTOM OF SCREEN WHEN WARM REPLACE D508 IN FOP - MA723TA5
EURO1 LOPTR AFTER WIDTH/HEIGHT INCREASE MCU2600 IC651.
EURO1 LOSES TUNING TUNER UNIT
EURO1 NEG PIC, SAD2140
EURO1 NICAM DISTORTION RHS DISTORT C1423 IT'S PART OF IC1401'S OSCILLATOR CIRCUIT.
EURO1 NICAM SND LOW AND DISTORTED & INT ONLY 1 CHAN - OK IN MONO IC1431 AMU2481 MULTI SND PROC CHIP
EURO1 NO BLUE R3374 100K DRIVE BIASSING RES
EURO1 NO BLUE R3374(100K)
EURO1 NO ON SCRN MENU'S TEXT OK,TPU2735 TELETEXT PROCESSOR CHIP
EURO1 NO OSD TPU2735 TEXT PROCESSOR
EURO1 NO PIC, C623 R628
EURO1 NO PIC/SND R622, Q624 T639
EURO1 NO PIC/SND,C623 R628
EURO1 NO SND/PIC 10V SUPPLY TO AV SW CHIPS; Q1011 2SC3940,R1102(4R7)C1102(0U1F SM)
EURO1 NO SND/PIC Q1011 2SC3940, R1102(4R7) 0.1UFSM C1102.
EURO1 NO SND/PIC STBY AFT FEW SECS R561 IC561 PT NO ERQ12HJ1R5
EURO1 NO SND/PIC,NO 10V ,Q1011(2SC3940)R1102(4R7)C1102-SM.
EURO1 NO/ODD OSD, TXT WORKS OK; TPU2735 TXT CHIP
EURO1 ODD TEXT/OSD BLACK LINES DU2553 DEFLECTION PROCESSOR CHIP IC1501.
EURO1 ON SCREEN MENUS COUPT TPU2735 TEXT PROCESSOR IC.
EURO1 ONLY WORKS IN AV MODE - OFF AIR SIGS SHUT DOWN THEN BACK ON WITH SNOW IC1401 MSP2410-08
EURO1 OSD ALL FUNNY TPU2735
EURO1 PIC BRIGHTNESS INCREASES UNTIL ALL WHITE DPU2553 DEFLECTION IC US
EURO1 PIC NEGATIVE AND UNSTABLE IC1601 SAD2140 US
EURO1 POOR NICAM AMU2481.
EURO1 POOR NICAM SOUND AMU2481 MULTI SOUND PROCESSOR CHIP IC1431.
EURO1 SERVICE MODE BASS TO MAX AND TREBLE TO MIN. PRESS VOL- ON TV AND RESET ON RC
EURO1 SLIGHT DISTORTION ON RIGHT SIDE SPEAKER C1423 R469 (470R)
EURO1 SLOW START THEN CUTS OFF IC1401 MSP2410.
EURO1 SND DIST ON RIGH CHAN C1423 PART OF IC1401 OSC CCT NEVER BEEN SOLDERED
EURO1 STARTS UP THEN SHUTS DOWN CONTINOUSLY LINE DRIVE BEING SW ON /OFF;IC1401 MSP2410-08 FAULTY AGAIN
EURO1 STBY , MSP2410 NICAM CHIP IC1401
EURO1 STBY AFT 10 SECS - SND OK NO PIC - FIELD COLLAPSE NO 27V SUPPLY TO FOP CHIP IC561 TDA8175 AS R561 1R5
EURO1 STBY FLASHED POWER ELECTROLYTICS.
EURO1 STBY R561 (ERQ12HJ1R5) TDA8175 IC561,
EURO1 STBY TDA8175 FIELD IC561 R561 1R5(ERQ12HJ1R5).
EURO1 TDA8175 MOD,FIT DIODE LINK B51 TOWARDS D562/R566.
EURO1 TEXT+OSD BLACK LINES DPU2553 IC1501.
EURO1 TOP CRAMP TDA8175+ FIT DIODE IN LNKB51 AWAY FROM CHIP.
EURO1 WEAK/NEGATIVE MONOCHROME PIC & POOR SYNC SAD2140 VIDEO AD CONV CHIP IC1601 - ALSO CHECK ACVP2205 ADAPTIVE COMB FILTER
EURO1 WHITE RASTER ALTERNATES WITH NORMAL PIC TXT OPERATION ALSO AFFECTED - WHITE WITH RANDOM GRAPHICS; IC1761 TPU2763 TXT CHIP FAULTY
EURO1 WHITE RASTER DPU2553 DEFLECTION PROCESSOR CHIP
EURO1 YELLOW PIC NO BLUE R3374 100K
EURO10 SERVICE MODE,BASS=MAX,TREBLE=MIN, VOLUME=MIN, TV (V DOWN) + REMOTE INDEX
EURO2
EURO2 SEE TV MAG JUNE 1999
EURO2
EURO2 SERVICING THE EURO-2 SEE TV MAG JUN 1999
EURO2 BENT SIDES EW, BC547B Q593.
EURO2 BENT SIDES,D536,L594.
EURO2 BLACK DIAGONAL LINES ACROSS PIC INT & INT CUTS OUT IC1701 TPU3040-18 TXT PROC CHIP
EURO2 BLACK LINES ON PIC, C311 150VN 21"125VN
EURO2 BRIGHT RASTER WITH FB LINES THEN OFF R378 3.3K. & R366 GOING OC ON CRT BASE & R366 100R SAFETY RES
EURO2 BRIGHT WHITE/STBY R376(560R 0.5W) R378(3K3 0.5W) R366(100R 0.5W FUSIBLE)
EURO2 BRIGHT/STBY R366(100R)
EURO2 COLD HEIGHT,IC601(VDP3108APP1)
EURO2 COLD NO COLOR/JUMPY VDP3108A-PP-A1,TPU3040,IC601,IC3502,X601 UNDER CAN
EURO2 CONTRAST BREAKING UP/ LINES ACROSS PIC SM C310 0.1µ - VOLTS AT COLL OF Q311 ONLY 3.8V INSTEAD OF 11V
EURO2 CONTRAST/LINES C310(0.1UF SM ) LEAKY NR Q311 LOC34.
EURO2 CUTS OUT WHEN HOT X601/IC601(VDP3108-30).
EURO2 DARK DIAGONAL LINES \ TPU3040-18.
EURO2 DARK VERTICAL BARS DOWN MAGENTA AREAS OF PIC I1601 VDP3108-25 ON BOARD A
EURO2 DARK VERTICAL LINES ON MAGENTA/PURPLE I1601 ON BOARD A,VDP3108-25
EURO2 DEAD - MAINS FUSE BLOWN POSITOR ARCING INTERNALLY
EURO2 DEAD 3.15AT +DEGAUSS POSISTOR WIDE LEGS.
EURO2 DEAD C622 C634 TDA4605+330K
EURO2 DEAD CHOPTR(2SK1118)+TDA4605-3+(2*150K)
EURO2 DEAD FUSE, DEGAUSS POSISTOR
EURO2 DEAD LOPTR BU2508AF CAUSE L1614/D16164.
EURO2 DEAD LOPTR BU2508AF D1614, A COIL L164
EURO2 DEAD NO LINE DRV 1.25AT,LOPTX
EURO2 DEAD PSU OK,NO LINE DRV,F851,D852(DARLINGT),CAUSE T501(DRVTX 5270103200)
EURO2 DEAD R7000(180K)+R7005(150K)START UP RESISTORS STR1006M.
EURO2 DEAD SURGE ON/OFF NO RED LED BC547 FRONT EDGE OF PCB
EURO2 DEAD TICKS, LOPTR/LOPTX
EURO2 DEAD TICKS, RELAY.
EURO2 DEAD UNPLUG W7002 FROM AUDIO BOARD R7000 150K AND R7005 180K
EURO2 E-W FAULT Q593 BC547B
EURO2 EW BOWING Q593,+39VZENDIODE ACROSS IT PANA MOD
EURO2 EW RASTER Q593(BC547B).
EURO2 EW WIDE BC547B Q593.
EURO2 EXCESS WIDTH & NO E-W CORR Q593 BC547B
EURO2 EXCESS WIDTH/EW BC547B Q53
EURO2 FIELD COLLAPSE & TRIPPING R7000 180K & R7005 150K BIAS FOR STR10006M - ON SIDE PCB
EURO2 FIELD COLLAPSE CHANGE FOP CHIP, D456 16V ZENER & D454 & CHECK ELECTS IN FOP STAGE
EURO2 FIELD COLLAPSE TDA8175+C563+R561(FUSIBLE 1R5)
EURO2 FIELD JUMP/JITTERS D507/D508 MEASURE OK
EURO2 FIELD NEDIS SELL A TDA8175-KIT IC
EURO2 FIELD SCAN & SHUTS DOWN DIS PINS 5 & 6 OF EAROM IC1203 - IF FIELD OPENS UP THEN EAROM IS FAULTY ELSE VDP IC601 & FIELD O/P
EURO2 FIELD SCAN INT VARIES & SHUTS DOWN IC1203 EEPROM ST42C08CB1
EURO2 FIELD TOP FOLDOVER D456 16V ZENER MA2160 IN FOP STAGE
EURO2 FIELD/TRIPPING R7000(180K)+R7005(150K) MARK TOP PLUGS.
EURO2 FLYBACK LINES AT TOP - INT D456 MA2160B
EURO2 GOES INTO LINES THEN CUTS OUT WHEN HOT CHECK XTAL X601 & IC601 VDP3108-30
EURO2 GOES OFF AFT 2 SECS AT SW ON - HT PRESENT REPLACE TZS9EK002-2 KIT -M INCS JUNGLE CHIP & EEPROM
EURO2 GREEN PIC CRT BASE RESISTORS
EURO2 HEIGHT VARIES/INT STBY ST42C08CB1 EEPROM IC1203
EURO2 HOT BOTTOM LINE PAIRING D50008(MA723TA5).
EURO2 HOT STBY TPU3040-18
EURO2 HOT STBY X601 OR IC601 VDP3108-30.
EURO2 INT FIELD COLLAPSE , FIELD CHIP LEGS LA8175
EURO2 INT FIELD JUMP D507/D508(READ OK)+R507(4R7)
EURO2 INT FIELD JUMP/JITTER AT BOTTOM OF SCREEN D507/D508 AND R507
EURO2 INT NO SOUND/COLOUR + BLUE NOISE ??
EURO2 INT SND(ODD NOISE),XTAL(TSS4004-B)
EURO2 INT STBY TPU3040-18 IC1701.
EURO2 JUST SNOW,TUNER UNIT
EURO2 LINE SYNC UNSTABLE IC1202 NOTE MODEL SUFFIX FOR CHIP TYPES
EURO2 LINE TEAR,TEXTOK,VIDEOPRO(VDP3108-APPA1)
EURO2 LO WIDTH ,C593(10NF).
EURO2 NO LINE DRIVE, PSU RUNNING, LED FLASHES ONCE PER MIN, JUMGLE I/C EEPROM KIT TZSEK002. THEN SELF TEST
EURO2 NO PIC/POOR SND,L4707 IN IF STRIP
EURO2 NO TEXT C3508 0.047UF
EURO2 PIC FADES,IC601(VDP310-PP-A1) IN IF CAN
EURO2 POOR PIC,VDP3108-29.
EURO2 POOR/PULSE STARTUP, IC2101(MSP3410-15TV)
EURO2 RAGGED VERTICALS IC601. NO VDP3108APPA1
EURO2 RAGGED VERTS & PIC BREAKUP IC601 DIG VID PROC CHIP VDP3108APPA1
EURO2 RED CAST CRT PHILIPS A51EAL55X01/SI
EURO2 RELAY CLICKING C637(2N2F)
EURO2 RELAY PULSING ONCE PER SEC WHEN OVER-RIDDEN HT VERY LOW - C637 2N2 POLYESTER CAP PIN 2 I611
EURO2 SELF CHECK , PRESS THE "STATUS" KEY ON THE REMOTE AT THE SAME TIME AS PRESSING TV "PROGRAMME DOWN"
EURO2 SERVICE MODE
EURO2 SERVICE MODE ,BASS TO MAX.& TREBLE TO MIN. NEXT PRESS REMOTE "REVEAL" & AT THE SAME TIME TV "PROGRAM DOWN"
EURO2 SERVICE MODE BAS TO MAX TREBLE TO MIN THEN VOL DOWN ON TV+REVEAL.
EURO2 SERVICE MODE BASS TO MAX AND TREBLE TO MIN. PRESS VOL- ON TV AND RESET ON RC
EURO2 SERVICE MODE1 BASS TO MAX. & TREBLE TO MIN. NEXT PRESS REMOTE "REVEAL" & AT SAME TIME "PROGRAM DOWN" BUTTON ON THE TV. EURO2 SERVICE MODE2 USING THE RED & GREEN BUTTONS ON THE REMOTE ONE CAN STEP THROUGH THE
EURO2 SERVICE MODE1 IN SOUND-MENU LOW-TONE-REGEL TO MAX AND HIGH-TONE-REGEL TO MIN.
EURO2 SERVICE MODE2 PRESS 'F' BUTTON ON TV.THEN PRESS VOL- ON TV AND REVEAL ON RC
EURO2 SERVICE MODE3 ADJUST: YELLOW AND BLUE BUTTONS. STORE:'STR'. EXIT: 'N' ON RC.
EURO2 SERVICE MODE3 ELECTRONIC SCREW DRIVER ADJUSTMENTS USING THE YELLOW & BLUE BUTTON TO ADJUST SETTINGS.
EURO2 SERVICE MODE4 SWITCHING THE RECEIVER OFF STORES THE SETTINGS IN THE EPROM'S.
EURO2 SND OK,NO PIC, OSD OK,L4707
EURO2 SND WHISTLE AUDIO PROCESSOR CHIP, VERY DEAR
EURO2 SNOWY PIC ,TUNER UNIT(ENV87880G3)
EURO2 SNOWY PIC C111 (0.068UF) LEAKY.
EURO2 SNOWY PIC WITH SMEARY RED & WHITE - TXT OK - DIG PROC CHIP VDP3108-29 . PAN SUPPLY IMPROVED TYPE ALONG WITH SM CAPS, EEPROM
EURO2 SNOWY SIGNALS C111 0.068µ LEAKY
EURO2 STBY BRIGHT LIGHTS & PHOSPOR BURN TO CRT RELAY RL6101 (PT NO TSE10818) & R668 ON PANEL E (& ALSO CRT )
EURO2 STBY DIODE ACROSS RELAY COIL LEAKING.
EURO2 STBY EEPROM CHI IC1203(X24CO16P-P1).
EURO2 STBY EHT RUSTLE ONLY EEPROM IC1203.
EURO2 STBY MODE DIFFICULT TO ENTER/LEAVE STICKING RELAY CONTACTS RL610, CLEAN OR REPLACE PT NO TSE10818
EURO2 STBY ONLY - INITIAL BURST OF EHT IC1203 EAROM
EURO2 STBY ONLY WHEN IC1203 EAROM CHIPS PINS 4 & 5 (CLOCK & DATA) DESOLDERED PIC CAME ON BUT DARK. X24C016P-P1 OR R558
EURO2 STBY R558 BEAM LIMITER.
EURO2 STBY, ON WHEN EERPOM IC1203, PINS 4 AND 5 WERE DE-SOLDERED. EPROM + R558
EURO2 STBY, Q1212(BC847B)
EURO2 STICKY STBY ,RELAY RL6101.
EURO2 TEXT CHARS ODD, VDP3108A VIDEO PROCESSOR CHIP IC1601
EURO2 TEXT LETTERS VDP3108A.
EURO2 TOP CRAMP TDA8175.
EURO2 TOP CRAMP/FOLD D456,16V ZENER TYPE MA2160 IN THE FIELD OUTPUT STAGE.
EURO2 TOP FLYBACK/TEXT LINES D456 MA2160B,NOTE D453=LINK
EURO2 TOP HALF OF PIC BLACKED OUT IC1203 NOTE MODEL SUFFIX FOR CHIP TYPES
EURO2 TOP STRETCH,JUMPY PIC,D456(16VZD)+R472(4R7),C456(220UF50V)
EURO2 TRIPPING - DUE TO FIELD COLLAPSE REPLACE FIELD CHIP & SM TFMR FAULTY/DRY JOINTS& R366 100R ON CRT BASE
EURO2 TRIPPING SLOWLY - OK WHEN PLUG W7002 DIS'D ON AUDIO PANEL AUDIO PSU DEAD - R7000 150K & R7005 180K
EURO2 TRIPPING/FIELD R7000(180K)+R7005(150K) WARNING MARK PLUGS.
EURO2 TUNES ONLY LO CHANNELS,TUNER UNIT
EURO2 TX25AD1DP DEAD - PSU TRIPPING UNPLUG W7002 ON AUDIO PANEL ALLOWS SET TO POWER UP - R7000 180K & R7005 150K
EURO2 TX25AD2 LO WIDTH WITH E/W CORR FAULTY C593 0.01MFD CERAMIC CAP
EURO2 TX25ADT COL ABSENT APART FROM BITS OF PINK/GREEN VDP3108A
EURO2 TX25MD1 NO SND/PIC WHEN COLD OK WHEN HEATED , IC2101 MSP3410-15(TV) AUDIO PROC CHIP (TRIPS WHEN COOLED)
EURO2 TX29AD1 NO SND/PIC JUST TICKING FROM RELAY COULD BE LOP FAULT BUT RELAY FAULTY IN THIS CASE
EURO2 TXT CHARACTERS HAVE PARTS MISSING VDP3108A VID PROC CHIP FAULTY
EURO2 TXT MISSING - DISPLAYS "P100" & "TEXT****" C3508 0µ047 SM CAP VIDEO FEED TO TXT PROC CHIP IC3502
EURO2 VERTICAL JITTER AFTER CHANGING IC601, KIT PART NUMBER TZS9EK002-2, INCLUDES EEPROM
EURO2 VERTICAL YELLOW BARS DOWN LHS,IC601(VDP310-PP-A1)
EURO2 YELLOW SMEARING VDP3108-25 COL PROC CHIP IC601
EURO2L SERVICE MODE BASS=MIN,TREB=MAX F BUTTON,HOLD(TV VOL- AND REVEAL)
EURO2L CUTS OUT ON HIGH BRIGHTNESS - BEAM CURR LIM R558 120K, MICRO IC1201 SHOULD SENSE BEAM I PIN 27
EURO2L DEAD DEGAUSS
EURO2L DEAD LOPTR CAUSE IF/DIGITAL CAN EARTHS
EURO2L DEAD LOPTR CAUSE METAL CAN EARTHS,RESOLDER ALL
EURO2L DEAD ODD LED FLASHS,IC601(VDP3108-APPA1),EEPROM(27CO10-603)
EURO2L EXCESS BRILL/BENT SIDES
EURO2L FIELD COLLAPSE FIT KIT TZS9EK002-2 (IC601 & EEPROM) - (£27 FROM SEME)
EURO2L FIELD COLLAPSE NOISY WFM FROM IC601 VDP3108-25 SIGS PROC CHIP - CHIP FAULTY (£35)
EURO2L FIELD COLLAPSE. IC601 VDP3108-25.
EURO2L FIELD SCAN VARYS ST42C08CB1 EEPROM IC 1203.
EURO2L FOCUS ARCING INSIDE CRT BASE SOCKET.
EURO2L FOP CHIP BLOWS REGULARLY REPLACE ASSOC DIODE AS WELL
EURO2L HI FREQ RGB INTERFERENCE PATCHES,VDP3108APPA1
EURO2L HT OK, NO LINE DRV R507(4R7) F851(1A25),Q503(2SD836A),T501(DRVTX)
EURO2L INT SNOWY PIC,TUNER UNIT ENV87880G3
EURO2L INT STBY BEAMLIMIT? R558(120K)+EEPROM X27C16P-F1.
EURO2L JUST SNOW,TUNER UNIT
EURO2L NO E-W CORR R702 22R 1/2W ;C554 510N 200V
EURO2L NO STATIONS FOUND, TUNER UNIT ENV87880G3
EURO2L POOR PIC GRAINY/BRIGHT PATCHES C601 VDP3108 VIDEO PROC
EURO2L SNOWY HIGHLITES IC601(VDP3108A)
EURO2L STBY ONLY IC601 VDP3108-25 SIGS PROC CHIP FAULTY
EURO2L STBY VDP3108-25).
EURO2L TOP BLANKED EEPROM IC1202 AND EAROM IC1203.
EURO2L TOP CRAMP IC451(TDA8175)+D456(MA2160B).
EURO2L TOP PIC BLANKING IC1203 EAROM+IC1202 EEPROM
EURO2L TUNER DRIFT, TUNER UNIT
EURO2L TUNING DRIFT & LOSS OF SIGS MID RANGE RESOLDER EARTHS IN TUNER
EURO2L TX28LD1/B WHITE SCREEN WITH VERT BLACK THIN LINES FROM COLD -OK IF IC601 HEATED IC601 VDP3108-25 LUMA/CHROMA PROC CHIP
EURO2L VCR INCOMPATIBILITY - PULLING AT TOP INCORRECT CHAN IN USE - USE CHAN 0 (AV)
EURO2L YELLOW SMEAR, VDP3108-25 COLOUR PROCESSOR CHIP.
EURO2M DEAD RELAY TICKS,LO HT,C807(100UF50V),C806(100UF50V) IN PSU PRIMARY
EURO2M FIELD COLLAPSE,IC451(LA7845)+D456(16VZD) PSU DERIVED POWER
EURO2M NO PIC,SND OK, F851,LINE DRV TX
EURO2M PIC FADES,VIDEO PRO(VDP3108APPA1)
EURO2M SLOW TRIPPING, LINE DRV_TX(5270103200)
EURO2M STBY, SHORT OUT RELAY,FIELD COLLAPSE ON HI A1'S
EURO2S DEAD DEGAUSS POSISTOR
EURO2S RELAY+LED PULSING C637(2N2F) FROM PIN2 TDA6505-3.
EURO2S33 RELAY+LED PULSING PULL BLUE WIRES PLUG FROM REAR SCREEN CAN.
EURO3
EURO3
EURO3 DEAD RELAY CLICKS,Q3801(2SD1474),ON PCB E.
EURO3H FIELD COLLAPSE MOD KIT TZS8EK003 REQD WHEN REPLACING FIELD CHIP IC451 TDA8350Q/N5. COSTS 22P - WORTH >£10
EURO3HW
EURO3HW STBY Q801(2SK1489MAT)
EURO4
EURO4
EURO4 SEE TV MAG JULY 2001 AUG2001 ONE-FOR-ALL CODE O650
EURO4 BENT SIDES EW ADJUST IN SERVICE MODE
EURO4 BIG PIC,LO A1'S L554,R702(8R2)
EURO4 COLD NO TEXT,IC1101(SDA5450C59)
EURO4 DARK PIC,LOPTX(A1'S)
EURO4 DEAD 3.15AH CAUSE TWO DEGAUSS POSISTORS
EURO4 DEAD C869,C871,Q852,CHOPTX
EURO4 DEAD C871(1000UF25V)
EURO4 DEAD EEPROM
EURO4 DEAD EHT SURGE LA7845N D558(?),R559(0R33)
EURO4 DEAD EHT SURGE,IC1101,IC1103(BR24C16 EEPROM)
EURO4 DEAD EHT SURGE,IC451,R559(0R33),D558(1SR124-4AT82)
EURO4 DEAD FIELD O/P CHIP IC451(LA7845N)+1K8SM C456(220UF50V)
EURO4 DEAD FUSE ,CHOPTX T801
EURO4 DEAD FUSE DEGAUSSS
EURO4 DEAD FUSE F602,LOPTX
EURO4 DEAD FUSE IC801(STRF6654LF51)
EURO4 DEAD FUSE UPGRADE TO 5A
EURO4 DEAD HT OK,IC601,L606(4U7H)
EURO4 DEAD IC601(VDP3120BPPB1)
EURO4 DEAD IC850(SE140N),D853(MA2180BLFS),D867(1N4007)
EURO4 DEAD LOPTR, KIT TZS9EK001
EURO4 DEAD Q552(2SD1877)
EURO4 DEAD Q853(BC847B SM),OPTO(TLP621GR-LF2)
EURO4 DEAD R877(0R47),BRIDGE RECT
EURO4 DEAD R877+D554+VIDEO HT CAP.
EURO4 DEAD SHORT OUT RELAY,LIGHT FROM TOP,D558(),R558(0R33)+REMOTE TO RELEASE STBY
EURO4 DEAD SHORT OUT RELAY,LIGHT FROM TOP,LA7845N+REMOTE TO RELEASE STBY
EURO4 DEAD STRF6654 D805(OPTO 4 LEG)
EURO4 DEAD/STBY AFTER FAULT NEEDS REMOTE TO RELEASE STBY.
EURO4 DEAD/STBY LA7845N+220UF50V
EURO4 DEAD/SURGE IF YOU BYPASS RELAY ONLY REMOTE WILL RELEASE STBY
EURO4 DROPPED CRACKED PCB UNDER LOPTX, +CRT SHADOW MASK SLIPPED
EURO4 EEPROM SELF CHECK,PRESS R/C STATUS+V- ON TV,THEN POWER OFF,THEN ON 45MINS
EURO4 EW BENT SIDES ON T/TEXT R701 100R
EURO4 EW BENT SIDES,D701(ISS133T-77)
EURO4 EXCESS BRILL LOPTX(A1'S)
EURO4 FIELD COLLAPSE/NO PIC IC451 LEGS
EURO4 FIELD HEIGHT INCREASES AND TWITCHES C402 0.33MFD
EURO4 FIELD RAINBOW,IC451(LA7845N),D557,R555(0R33),D558,R559,D454
EURO4 FIELD SHIFT,IC601
EURO4 GET BRIGHTER THEN OFF, PHILIPS CRT FAULTY
EURO4 IC2702 BURNT (TDA2030A).
EURO4 INT DEAD/STBY , LO 5V STBY SUPPLY D869
EURO4 INT START UP,R814 47K IN PSU+ C816(100UF25V)
EURO4 INT STBY C454 (22NF SM) NEAR FIELD IC.
EURO4 INT STBY CRT INTERNAL ARCING
EURO4 INT STBY Q857(2SA1018QTA),Q852(2SC1383QRS)
EURO4 INT STBY RELAY,C454(22NF),C851(220UF160V),C811(180UF400V),R805,R814,C816,STRF6654
EURO4 INT STBY STRF6654
EURO4 INT STBY,D868(1N4150T-27)
EURO4 INT STOPS C454(220NF),R601(100R)
EURO4 INT TRIPS, RESOLDER EVERYTHING
EURO4 LINE SHIFT,IC701(TEA2031A)
EURO4 LINE TEAR IC601(VDP3120BPPB1)
EURO4 NO LINE DRIVE,C509,Q5903(2SD2398-M2)
EURO4 NO PIC INT,LOPTX
EURO4 NO SND EARPHONE OK,SPKR PLUGS IN WRONG SOCKETS
EURO4 NO SND IC2704,IC2703 ,D2710
EURO4 NO SND/SQUEEL,D2614 D2715(1SS133T-77) CAUSE EXTERNAL SPKRS
EURO4 NO SURROUND SND TDA2030.Q2701 Q2702
EURO4 NO/POOR OSD,EEPROM IC1103(X240RZ-01GA)
EURO4 ODD CONVERGENCE,CRT FAULTY
EURO4 OUT WHEN WARM - MAY RETURN TO STBY RESOLDER DRY JOINTS ON IC801 (STRF6654LF51)
EURO4 PANASONIC/PHILIPS/LG CRT FAULTY
EURO4 PIC FLASHIING IC601
EURO4 POOR FUCUS LOPTX
EURO4 PSU STARTS/STOPS,R877(47R 2W)
EURO4 RAGGED LINES ,P BOARD IC3901
EURO4 SERVICE MODE BASS=MAX TREBLE=MIN PRESS "F" THEN TV VOL+ AND REMOTE INDEX, RED/GRN,STR
EURO4 SLOW/POOR START, WIDESCREEN CRT INTERNAL ARCING
EURO4 SMELL/HUM NOISE,SND PCB BURNUP IC2704(TDA2040A) CAUSE EXTERNAL SPEAKER LEADS
EURO4 START.STOP D558
EURO4 STARTS/STOPS HT FEED RES R877, D554 200V RECT
EURO4 STARTS/STOPS IC451(LA7845N)
EURO4 STBY-IF STBY RELAY OVERIDED & A1 INCREASED HAS "RAINBOW" EFFECT CHECK VERT O/P CHIP & VDP3108BC2 JUNGLE CHIP
EURO4 STBY ,Q854(BC847B SM),C871,D867(1N4007)
EURO4 STBY C454(22NF),Q857(2SA1018QTA/BF423)
EURO4 STBY C851(220UF160V)
EURO4 STBY EHT SURGE,C454(220NF)
EURO4 STBY FIELD,D558,R559
EURO4 STBY IC451,C454(22NF SM)
EURO4 STBY PSU PULSING,LOPTR(BU2508/2SD1577)R507(100R),LINE DRV TX PINS
EURO4 STBY Q853(RELAY DRIVER)
EURO4 SURGE,DEAD DISCONN EEPROM PINS 4+5, IF OK WITH FIELD COLLAPSE C454(22NF/50V SM)
EURO4 SURGE,DEAD DISCONN EEPROM PINS 4+5, IF OK WITH FIELD COLLAPSE LA7845
EURO4 SURGE,DEAD SHORT RELAY,TEST FIELD COLLAPSE LA7845
EURO4 SURGE/DEAD D554
EURO4 TX32PK2C NO REAR SURR SND IC2704 TDA2030AV
EURO4 WARM TRIP C464(220NF)
EURO4 WARM TRIP,R872
EURO4 YELLOW PIC /NO BLUE CRT PHILIPS/LG WIDESCREEN
EURO4 YELLOW SCREEN/LINES R558(120K)
EURO4D NO PIC SND OK,C454(22NF SM),IC451
EURO4D SURGE/STBY C454(22NF50V SM CHIP CAPACITOR) FROM PIN 7 FIELD OUTPUT CHIP
EURO4H SEE TV MAG JUNE2003P461
EURO4Z CT2153STX DEAD WITH Q551 LOPTR FIT REPAIR KIT TZS9EK001
EURO4Z DEAD Q951(2SC4004) ,R954(6R8), D958 (1N4148) , R975(270R FUSIBLE) R964 (82R 1/8W) D953 A 12V ZENER
EURO5
EURO5
EURO5 SEE TV MAG DEC2001 1997 MODEL
EURO5 DEAD/STBY D803(12V ZD)
EURO5 EEPROM RESET,HOLD TV VOL-,REMOTE STATUS(ABOVE RED)
EURO5 LOOKS LIKE CRT,FLARING HILITES,C386(3U9F2KV),C397(2N2F2KV).
EURO5 SELF CHECK,PRESS SET -V AND REMOTE STATUS,THEN POWER OFF.
EURO5 TRIPPING C584(390PF2KV)
EURO5L 'DOWN' (-)'STATUS' REMOTE, 'OK''--'.
EURO5L SERVICE MODE BASS=MAX,TREBLE=MIN' REMOTE REVEAL' OR ' INDEX' VOL+,RED,"N"
EURO7
EURO7 INT ODD COLOR, DIG BOARD EXCHANGE UNIT
EURO7 NO SURROUND SND. NO 40V ON Z BOARD -2A5 FUSE R2420, 4A FUSE R2419,ZENER D2401 MA4200(30V)
EURO7 PCB-DG NOT REPAIRABLE EXCHANGE
EURO7 SELFCHECK/RESET PRESS TV(V DWN)+REMOTE STATUS,THEN POWER OFF
EURO7 SERVICE MODE BASS TO MAX, TREBLE TO MIN, THEN HOLD DOWN REMOTE INDEX PRESS TV V BUTTON
EURO7 SERVICE MODE BASS TO MAX,TREBLE TO MIN ,TV(V DOWN)+REMOTE INDEX
EURO7) SERVICE MODE,SET BASS LO/TREBLE HI,THEN HOLD R/C INDEX AND TV V
EURO8
EURO8F CORRUGATED VERTS & COL HOR BANDS Z950 FUSE HAD INCREASED IN VALUE TO 0R3
EURO8F DEAD Z950 FUSE , Q901 CHOPPER TR , D909 ZENER & R901
EURO9L DEAD Q551(2SC5905)
FIELD COLLAPSE CHANGE C454 22NF/50V SUFACE MOUNT.
FX74 PSU BLOWN STRS6709 REPLACED (DRY JOINTED); 0R47 RES & 16V & 8V ZENER
GP1
GP1 DEAD HT AT 30V C851 SHORT .1 AT 400V LOCATED BY IC851
GP1 STBY D853 CRT HEATER DIODE
GP1 STBY IC801(STRF6656),D809(MAZ20820A0LS)
GP4L
HT CORRECT - NO LINE DRIVE; REMOVING PROT TR Q451 REVEALED FIELD COLLAPSE CAUSED BY D453 MA2270 ZENER DIODE -
IC1101 MICRO PIN 6 SHOULD BE HIGH (POWER ON COMMAND) BUT WASN'T AS CHIP NOT BEING RESET. IC1104 RESETS
IC1101 WHEN ITS SUPPLY REACHES 5V BUT DIDN'T REACH THIS LEVEL AS ZENER D810 IN THE 5V REG CCT WAS LEAKY
M11
M11 INT ROLL ON DARK SCENES, R508(680K) GOES HI.
M11 TELETEXT - LINES AT TOP OF PIC. C412 ( 3.3U F ) .
M12C NO GO OFTEN INT. R513 680R DRY21V1 SMEARY VIDEO CHECK C684 ON V MODULE 22MFD BI-POLAR - USE 2 IN SERIES.
M8
M8 DEAD - WITH CLICKING NOISE. DRY JOINT AROUND C553 , C556.
M8 REDUCED FRAME SCAN - NO VIDEO INFO. C564 ( 10U F , 250V ) LEAKY , REPLACE R559 ( 3.3 )
M9
M9 FOCUS - DEFOCUSED PIC - DIM. LOPTX
M9 FRAME - ROLL ON DARK PICS. R508 ( 680K ) HIGH BY IC501.
M9 TELETEXT - LINES INCH DOWN. SHUNT D603 WITH 0.47UF.
M9 TELETEXT - LINES. C412 ( 4.7U F 250V ) .
MX
MX1 INT FIELD VERTICAL JUMPING,IC401
MX1 VOLUME WILL NOT VARY CXA2021S SND PROC CHIP
MX3 HOTEL MODE PRESS BOTH 'OFF TIMER' ON RC AND 'CH.UP' ON TV.
MX3 SERVICE MODE PRESS BOTH 'RECALL' ON RC AND TV 'VOL-' EXIT='NORMAL'
MX3C HOTEL MODE OFF: PRESS SIMULTANEOUSLY 'OFF TIMER' ON RC AND TV 'VOL-'
MX3C HOTEL MODE ON: PRESS SIMULTANEOUSLY 'OFF TIMER' ON RC AND TV 'CH.UP'
MX3C HOTEL MODE PRESS BOTH 'OFF TIMER' ON RC AND 'CH.UP' ON TV.
MX3C SERVICE MODE PRESS BOTH 'RECALL' ON RC AND TV 'VOL-' EXIT='NORMAL'
MX3C SERVICE MODE PRESS BOTH 'RECALL' ON RC AND TV 'VOL-' . EXIT 'NORMAL' ON RC.
NO LINE SYNC C505(4N7),C506(33NF),AN5150N
NVHS820 TRACKING,LOADING ARM GEAR
NVVHD1 VCR/DVD COMBI NO DVD,DRAWER NO OPEN,F498 DISPLAY,FLASH ROM IC37001
ON/OFF SWITCH BUTTON SPACER TKK188514/1 FITS ON SWITCH END
PC2033 CHASSIS NMX-GX. LOPTR CAP(2N2 1K5)
PC33V92S D816-116VZEN DIODE & LOPTR Q551. LINE DRIVER & XFOMER
PIX-M2 BRILL VARIES,TRIPS C555(10UF).
PIX-M2 INT START,DEAD T801+Q801 PINS.
POOR PIC SWAF PINS, POOR CONTRAST AN5150N OR PARTS FROM PIN 12,13,14.
SERVICE MODE1,WITH TV ON TOUCH TP8 TO CHASSIS(FA-1 TO FA-2 ON A BOARD).
SERVICE MODE2 OSD YELLOW "CHK" TOP RIGHT PRESS THE ACTION BUTTON SERVICE MODE2 AND VOLUME UP BUTTON ON THE FRONT PANEL AT THE SAME TIME. SERVICE MODE3 "CHK" WILL TURN RED. USE REMOTE POWER BUTTON TO SELECT SERVICE MODE4 AJUSTMENTSB,SUB-ADJUSTMENTS;C,CRT
SERVICE MODE5 S FACTORY ADJUSTMENTS ONLY; NORMAL TV, NORMAL OPERATION OF CHANNEL AND VOLUME BUTTONS.
SERVICE MODE6 PRESS ACTION AND POWER TOGETHER FOR 2 SECONDS TO STORE.
SURGE START BUT STOPS,DISCONNECT PINS 4+5 OF EPROM,
T14S3R DEAD D861.
T14S3T NEG PIC EEPROM IC1205.
T14S3T POOR/ROLLING PIC - VID INVERTED REPLACING IC601 MADE NO DIFFERENCE - IC1205 EEPROM FAULTY
T262GA NO SND AUDIO O/P TR 251 ON MAIN PCB B-E - USED TIP41C IN LIEU
TC-21 S3R(Z7) PIC FADES, HEATER SUPPLY
TC100
TC100G DEAD LOW HT R816 330K.
TC100G DEAD R816 330K
TC1100 WON'T START TOUCH CHOPPER E/C TO START (330K+1M)
TC1302 M6
TC1303 M6
TC1400T INT PIC, R545
TC1400T INT SNOW R545
TC1404 M11
TC1405 M11
TC1406 M11
TC1407 M12
TC1408 M12
TC1460 Z1
TC1465 Z1
TC1465 Z1 GOTO Z1
TC1470 Z1
TC1475 Z1
TC1480 Z3
TC1480T
TC1485
TC1485 Z3
TC1485T
TC1485T Z3
TC1485T Z3 1990
TC14B3R DAEWOO CP375 GOTO DAEWOO
TC14B3R DEAD C406(470NF) R806 R807
TC14B3R ODD COLOR, DEGAUSS
TC14B3R Z375 (DAEWOO CP375)
TC14B4R(/B) Z185 (DAEWOO CP185)
TC14JR1 Z7
TC14K1R Z7
TC14L3R MX1A
TC14S1M Z5
TC14S1R Z5
TC14S1R/B Z5 REMOTE TNQ8E0460
TC14S1R/BH Z5
TC14S1R/BH Z5 REMOTE TNQ8E0461
TC14S2R DEAD CHECK D806 IN POWER SUPPLY
TC14S2R Z5
TC14S2R Z5 REMOTE TNQ8E0460
TC14S3R
TC14S3R DEAD R811,R804
TC14S3R EEPROM RESET, TV PRESS "F" +VOL DWN,+REMOTE STATUS BUTTON
TC14S3R NEG/LINEY PIC,EEPROM(ST24C02AB1)
TC14S3R POOR CONTRAST,EEPROM IC1205(XL25D02P-AA1)
TC14S3R POOR PIC,EEPROM
TC14S3R Z7
TC14S3R(/W) Z7 REMOTE TNQ8E0460
TC14S3RC Z7 NONUK PAL B/G
TC14S3RL
TC14S4RL Z7 REMOTE TNQ8E0460
TC14SIR Z5
TC1585 Z3
TC15M1 Z4
TC15M1M Z4
TC15M1R STBY FIELD O/P CHIP
TC15M1R SURGE.OFF FIELD IC
TC15M1R Z4
TC15M1RP Z4 DEAD STRS54041,2SD865R,4R75W,+CAPS
TC15M1T Z4
TC15M2 Z4
TC15M2R Z4
TC15M2R Z4 REMOTE TNQ8E0448
TC15M2T Z4
TC15MIR Z1
TC1601 M11
TC1602 M11
TC1631
TC1631 U4
TC1632 U4
TC1633 U4
TC1635 U4
TC1637 U4
TC1641 U4
TC1651 U5
TC1665 Z1
TC1675 SEE Z1
TC1675 Z1
TC1752 U5
TC1785
TC1785 Z3
TC1785 Z3 DEAD AFT 5 MINS STR50103A-M (USE PAN SPEC VERSION - OTHERS WON'T WORK PROPERLY)
TC1786 Z3
TC1802 M11
TC1802U M7
TC1803 M7
TC1807 M9
TC1808 M11
TC1810 M11
TC1830 M12
TC1832 M12
TC195
TC200 M11
TC2000 U3
TC2002 U1
TC2006 M7
TC201 M9 M11
TC2011 U3W
TC202
TC202 M11
TC202 PIX-M9
TC202 TEXT LINES C412(4U7F).
TC202 TEXT LINES SHOWING AT TOP C412(3U3F).
TC2020 M11
TC2024 U3W
TC2026 TOP TEXT LINES, MOD CHANGE R424(100K) TO 47K+47UF ACROSS D603.
TC202G BAD TEXT LINES/SLOW FIELD FLYBACK C412 4.7UF, 250V
TC202G INT ROLLS R508 680KOHM, FROM PINS 14 AND 16 OF IC501,
TC202G PIX-M9
TC2030 M12
TC2030 M12 GOTO M12
TC2031 OFF R811 & R817 (1R) IN PSU
TC2031 U4W
TC2033 U4
TC2035 M11
TC204 M9
TC2043 U4W
TC2043 U4W GOTO U4
TC2051 U5
TC2055 M11
TC2055 M11 GOTO M11
TC2056 M11
TC2061
TC2061 U5
TC2076 M11
TC208 U3
TC2086 M11
TC20L3A MX1
TC210 M11
TC211 M12
TC2110
TC2110 NO PIC. LOPTRANSISTOR READS IN BUT OK OUT - LOPTX FAULTY.
TC2110 SET WON'T GO OR GOES OFF AFTER 20MINS MAINS TX OC
TC2110 U5N
TC2112 U5
TC212 M11
TC214 M11
TC215 M12
TC216 M11
TC2160 U5 GOTO U5
TC2160 U5N
TC217 M11
TC2175 NO COLOR. 470U F 16V BY DECODER IC.
TC2175 Z1
TC218 M11
TC2185 Z3
TC2195 Z3
TC2195 Z3T
TC2195DRS Z3T DEAD PSU NOISE. LOPTX TLF15606F
TC2195DRS(Z3T) PSU NOISE,LO HT,LOPTX
TC21DQ DEAD LOPTR CAUSE HI HT
TC21K1R Z7
TC21L3R MX1A
TC21M Z4
TC21M1R
TC21M1R Z4
TC21M2R Z4
TC21M2R Z4 REMOTE TNQ8E0447
TC21M2T Z4
TC21MIR
TC21MIR Z4
TC21R ALPHA2
TC21R1
TC21R1 GOTO ALPHA2
TC21R1 ALPHA2
TC21R1 HOT LO HT (121VN) POWER ?
TC21R1 LOPTX TLF15506F/ETH1953AY/1000 FUSIBLE 2SD1439.
TC21R1 UNLOCKED COLOR C642 10NF
TC21S1 Z5
TC21S1 Z5 REMOTE TNQ8E0461
TC21S15R WHAT SERVICE CODE ? WWW.CALANAN.COM/PANASONIC.
TC21S1R GOTO Z7
TC21S1R DEAD STR51424
TC21S1R Z5
TC21S3 Z7
TC21S3R Z7
TC21S3R Z7 PIC FADES SND OK,RESOLDER CRT BASE PCB
TC21S3RC Z7
TC21S4RL Z7 REMOTE TNQ8E0460
TC220 M11
TC2201 INT LINE COLLAPSE D809(5VZ)+D819(6VZ)+D815+R813(1K).
TC2201 INT LINE COLLAPSE R525 68R+BU208A LOPTR ZENNERS D809(5V) AND D819(6V) D815 R813 1K
TC2201 LINE TEARING TR801.
TC2201 NO PIC MOTORBOATING IC301(AN331).
TC2201 PIUS1C FRAME INT COLLAPSE. 454/455.
TC2201 PIUS1C TRIPPING PULSATING SND , EHT & FRAME COLLAPSE C816 ( 220UF ) , C813 ( 1UF ) , C1029 ( 10UF ) D809 , D819
TC2201 U1 PIU-S1C
TC2202 U1
TC2202 U1 GOTO U1
TC2203 DEAD R832(150R).
TC2203 FIELD COLLAPSE R442 1R0 O/C.
TC2203 NO PIC/SND R810.
TC2203 NO RASTER EHT OK, D818
TC2203 U1
TC2204 INT LINE JITTER C510(100UF16V).
TC2204 U1
TC2205 BOTTOM AREA BLACKED OUT MOVES UP, IC401(TDA1104SP).
TC2205 FAINT WHITE BANDS ACROSS+VOL VARIES,C854(10UF)+C852(100UF).
TC2205 LINE HOLD VARIES CENTER PATTERN, C856(10UF).
TC2205 SOUND LEVEL ALTERED BY CONTRAST POT, C857(47UF).
TC2205 STBY D852/D853.
TC2205 U2
TC2206 U1/U4
TC2207 U2
TC2208 U2
TC2209 U3
TC221 U3
TC221 U3 GOTO U3
TC2210NS M11
TC2210SP M8
TC2210VR M12
TC2211 C853(100UF)+C854(47UF).
TC2211 LINE HOLD
TC2211 LINE HOLD DRIFT WARM C510(47UF25V).
TC2211 U3W
TC2211 U3W LINE TEARING C835(100UF250V)+C854(47UF250V).
TC2213 BENT VERTICAL,POWER NOISE, C809( 1UF).
TC2213 DARK PIC+NO CHANNEL STORE OR CHANGE,Q552(2SD762).
TC2213 DEAD Q802(2SD965R) IN PSU.
TC2213 FIELD COLLAPSE, Q403.
TC2213 INT PIC/SYNC, REMOVE TEXT BOARD+LINK PINS 4-6 T2.
TC2213 REDUCED HEIGHT R461/2.
TC2213 U3W
TC2216 U3W
TC2216 U3W CHASSIS DARK ONE SIDE 10UF250V NEAR LOPTX
TC2216 U3W FIELD COLLAPSE DARLINGTON+
TC2216 U3W WHISTLE LINE PAIRING C809 1UF250V
TC222 M11
TC2220 M11
TC2221 U3
TC2223 U3
TC2225 U3
TC2226 U3
TC2229 U3
TC223 M12
TC2231 M7
TC2232 U4W
TC2233 U4W
TC2233 U4W INT TEXT LINES ,C453(100UF35V),C454(47UF25V)
TC2234 U4
TC2235 M11
TC2235UR U4
TC2239 U4
TC224 M11
TC2240 U4
TC2243 U4
TC225 EW RASTER O/P TR O/C) (
TC225 FIELD COLLAPSE DRY JOINTS Q403
TC225 U3
TC2251 M8
TC2253 U5
TC2255 M11
TC2256 M11
TC2263 U5
TC2271 M8
TC2276 M11
TC2283 U2 / U3
TC2291 U2
TC2292 U2
TC2293 U2
TC230 M12
TC232 M12
TC233 M12
TC234 M12
TC235 M12
TC2461 U5
TC2475 ALPHA1W
TC2475 BLANK RASTER TDA4505M CAUSE FOCUS FLASHOVER.
TC24R1 ALPHA2
TC26 M11
TC2600 M8
TC2603 M11
TC261 HT VERY LO D812(SV03)+TR802(2SA636).
TC261 M8
TC261 TRIPPING D554.
TC2610 M11
TC262 M7 PIUS1
TC2620 M11
TC2622
TC2622 U3W
TC2629 U3
TC262G M11
TC262GA PIUS1
TC262SPM M9
TC2630 M12
TC2633 U4
TC2634 U4
TC2635 M11
TC2636 U4
TC2636 U4 LOPTX+ C808 47UF, 16V.
TC2637 U4
TC2640 U4
TC2641 U4W
TC2650 M8
TC2651 M8
TC2656 M11
TC265SPM M9
TC2665 M11
TC2671 M8
TC2675 M11
TC2676 M11
TC2680 U2
TC2681 U2
TC2683 U3
TC2684 U3
TC2686 M11
TC2690 U3
TC271 M8
TC272 M8
TC273P M7
TC273S M9
TC273SP M7
TC273SPM M9
TC273W M12
TC274 M7
TC275 PIX-M8 M11
TC275G DEAD CLICKING C553+C556.
TC275G LO HEIGHT+LO HT(165VN) C564(10UF)+R559(3R3).
TC275G PIX-M8
TC290 M7
TC292 M9
TC293 M7
TC294 M11
TC295 M9
TC296 M11
TC297 M9
TC297NP FLYBACK LINES - LACK OF DEFINITION. C356 ( 1U F ) ON CRT BASE.
TC297NP HOT FLYBACK LINES C356(1UF).
TC298 M11
TC300SP M6
TC333 PIX-M6
TC333G PIX-M6
TC361
TC361 COLD LOWER BLANKING C857.
TC361 COLD TRIPPING D552.
TC361 EXCESS BRILL+LO HEIGHT C564(10UF).
TC361 INT FIELD COLLAPSE C115 15UF, C118 1UF, AND C139 0.47UF,
TC361 INT ROLLS C115(15UF)+C118(1UF)+C139(0U47F).
TC361 INT TRIP D552 IT'S ACROSS THE SCAN THYRISTOR.
TC361 M7
TC361 TRIPPING FROM COLD. D552 IN PARALLEL WITH SCAN THYRISTOR.
TC371 PBX-M7A2
TC381 PIX-M6A
TC381G BLACK AREA AT BOTTOM RIGHT-HAND SIDE. C857 ( 0.47U F ) BIPOLAR.
TC381G BLACK BLOB C587, A 0.47UF BIPOLAR IN THE BLANKING CIRCUIT.
TC381G BLANK BOTTOM RHS C857(0U47F).
TC381G BRILL VARIES+ITN TRIP C555(10UF).
TC381G DEAD - GIVES ONE TRIP AT SW ON HT OK; LOPTX U/S
TC381G M6
TC381G RASTER - BRIGHT - SET TRIPPING. GRID-CATHODE SHORT IN 320BTB22 TUBE.
TC381U M6
TC400 M11
TC410 M11
TC421 M11
TC4230 M12
TC42G DARK LHS C514(4U7F).
TC430 DEAD R512(WARM), IC501(AN5435) .
TC430 DEAD R512, A 10K
TC430 M12H
TC430G M12H
TC431 DEAD INT, R513 PINS.
TC431 DEAD NO LINE DRV R510.
TC431 M12C
TC431GR M12C
TC431GR M12C DEAD 680OHM, R513
TC450 M12H
TC450 M12H CHANNEL BUTTON NO LONGER AVAILABLE
TC450G M12H
TC4688 M12
TC471 M11
TC471NP M7
TC471SP M7
TC471SPM M9
TC481 EXCESS BRILL,C531(10UF250V),R369(820K) ON CRT BASE
TC481 INT LOSS SIGNALS R545 DRY
TC481 INT PIC/SND R545 3R3
TC481 M6
TC481 NO SIGNALS INT 12V, R545(3R3).
TC482 M11
TC482S M6
TC482SP M6
TC4830 M12
TC486 LINE HOLD DRIFT. C505 ( 1U F )
TC48G
TC48G LINE DRIFT C505(1UF).
TC492
TC492 PIX-M11
TC492G PIX-M11
TC493 M11
TC610 M11
TC610SPM M9
TC681MN M12
TC681MRS M12
TC681UR CHAN 16,Q1023 TIP31C
TC681UR STUCK CHAN 16, Q1023(TIP31C).
TC682 PIX-M11
TC682G BRILL VARIES INT TRIPPING C555(10UF).
TC682GR PIX-M11
TC683 M11
TC684 M11
TC685 M11
TC687 M12
TC688 M12
TC785 Z3
TC800 X8
TC800G FIELD COLLAPSE C407(3U3F).
TC800G FRAME COLLAPSE. C407 ( 3.3UF , 16V ) TANTALUM.
TC810 M11
TC811 M11
TC815 M11
TC816 M11
TC817 M11
TC820 M11
TC830 M12
TC831 M12
TC85
TC85G HOT PIC FADES IC103(AN231).
TC862G LINE DRIFT C505(1UF).
TC862G LINE HOLD DRIFT. C505 ( 1U F )
TC871 M8
TC872 M8
TC873 M8
TC874 M7
TC874SPM M9
TC890SPM M9
TC890W M12
TC9200 U1
TCAL20 M11
TCAL26 M11
TCV1 M11
TCX74 ALPHA1W
TDA8175
TDA8175 0 CHANGE TDA8175 to TDA8172
TDA8175 1 Replace defect TDA8175 with TDA8172
TDA8175 2 Remove R566 (4,7K)
TDA8175 3 Mount a 3.3K resistor from pin 1of the TDA8172 to the (now free) pad
TDA8175 4 of R566 with connection to the large screening can.
TDA8175 5 Mount a 10K resistor from ground to pin 7 of TDA8172
TDA8175 6 Mount a 10K resistor from +5V to pin 7 of TDA8172.
TDA8175 7 +5V is present near the large screening can.
TDA8175 8 Turn on the TV. If necessary, the height of the picture can be
TDA8175 9 adjusted through the service menu or by adjusting the value of
TDA8175 A the 3.3K resistor slightly (lager value = smaller height)
TH42PA20 PLASMA INT STBY IC551(C5HABZZ00123)
TH42PE30B PLASMA DEAD LED FLASHES,IC6408 BURNT SCAN PANEL SD(TNPA2958AB)
TH42PX60 DEAD POWER BOARD TNPA3911
TH50PZ700U 50 INCH PLASMA TV
TH50PZ700U BYD33D,200V,1AMP FR103, HER103, NTE552, NTE574.
TH65PV500 PLASMA SCREEN DAMAGE
TR5030G
TR5030G BLACK AND WHITE SET NO EHT,AN5750 IC41,
TR5030G NO EHT AN5750.
TX-14B4T(Z185) NO PIC BRIGHT SCREEN,EEPROM
TX-21CK1 Z8 NO STBY LED, Q1107 (BC847B).
TX-21S3T DEAD NO LINE DRIVE,D861
TX-2470 RAGGED VERTICALS PSU NOISE C808(10UF50V)
TX-32PK3 STBY AT SWITCH ON C454 (22NFSM).
TX1
TX1 ALPHA1
TX14/21GV1 COMBI DEAD STBY LED BLINKS C840(47UF25V)
TX143T Z375 TRIPPING - STBY LED FLASHING ,LOPTX
TX1485 ALPHA1
TX14B NO PIC/SND OSD K, EEPROM
TX14B3T CP375 DEAD 4AT+DEGAUSS POSISTOR
TX14B3T DAEWOO CP375 LOPTX(1142 5077)
TX14B3T TUNING ON FRONT BUTTONS
TX14B3T Z375
TX14B3T Z375 FIELD COLLAPSE IC301 TDA8456 - MOD - C309 TO 22µ 100V, ADD 0µ01 ACROSS R310 & FIT 2R2 1W IN JUMPER R420
TX14B3T Z375 (DAEWOO CP375)
TX14B3T Z375 FIELD COLLAPSE,IC301(TDA8356)+C309(22UF100V)
TX14B4 PLUGTOP INTERNAL SHORT
TX14B4T Z185 : NO SOUND OR PICTURE. NOT TUNING,OSD ok
TX14B4T DAEWOO CP185 GOTO CP185
TX14B4T Z185
TX14B4T Z185 BRIGHT SCRN NO PIC, MEMORY CHIP I702(X24C)
TX14B4T Z185 (DAEWOO CP185), 2003 AROUND £110 SERVICE MODE: SELECT CHANNEL 99, SET SHARPNESS TO MINIMUM, HOLD SET'S DOWN KEY AND PRESS MUTE ON REMOTE AT THE SAME TIME. USE THE UP/DOWN KEYS TO SELECT ITE
TX14B4T Z185 NO TUNING NO SND/PIC,EEPROM IC702,C832(2200UF16V),C863(1000UF16V)
TX14B4T Z185(DAEWOO)NO TUNING NO SND/PIC,EEPROM SERVICE KIT TZS9K021
TX14B4TL Z185
TX14BT Z185
TX14C3T/S Z7
TX14GV1 COMBI BACKUP CAP LEAKY CN59 (CDYF0H105K) (5.5V 1UF) œ19.95
TX14GV1 COMBI DEAD RELAY CLICKING C840(47UF25V) IN STBY SUPPLY
TX14GV1 COMBI NO EJECT/TRIPPING C840(47UF25V) IN PSU
TX14GV1 COMBI DAEWOO CP421
TX14GV1 COMBI INT NO START,L702,D705 ON BOTTOM PCB
TX14GV1 COMBI STBY LED BLINKS C840(47UF25V)
TX14GV1 POOR/NO START,D830(1N4007)
TX14GV1 Z421 (DAEWOO CP420, K-MECHA DECK)
TX14GV1L LOCKING UP , REPLACE BOTH THE MAIN MICROPROCESSOR I701 MS5457CU1, I703 X24C-14GV1
TX14GV2 Z082PF (DAEWOO CP082), DECK K30 PSU I801 STRF6653
TX14J1
TX14JT1 CAN'T STORE FIRST CHANNEL ,EEPROM(X24S11-1MAZ)
TX14JT1 POOR/NO STORE, EEPROM(X24S11-1MAZ)
TX14JT1 Z7
TX14K1T Z7
TX14K2T Z7
TX14S1R Z5
TX14S1T DEAD PSU NOISE, R821(330K)
TX14S1T Z5
TX14S1T/B(OR BH) Z5 REMOTE TNQ8E0461
TX14S2T ALPHA1
TX14S2T LACK OF HEIGHT WITH FOLDOVER REPLACE R521 8R2
TX14S2T Z5
TX14S2T Z5 REMOTE TNQ8E0461-1
TX14S3T ALPHA1 POWER REGULATOR CHIP "A" TYPE
TX14S3T(/W) Z7 REMOTE EUR511300
TX14S3TC Z7 NONUK PAL B/G
TX14S4TL Z7 REMOTE EUR511300
TX15AT1 ZM3L (ORION CHASSIS) REMOTE EUR511300 PCB MARKED TMB538A
TX15LT2 LH1 CHASSIS (LCD TV) 2001
TX15LV1 LH5 CHASSIS (LCD TV + DVD PLAYER) 2002
TX15M Z4
TX15M1R ALPHA1
TX15M1T Z4
TX15M1T9 OSG=C ,RESET MICROPRO HOLD DOWN TIMER BUTTON(RC)+PRESS VOL DWN(TV).
TX15M2T ALPHA1
TX15M2T Z4 TNQ8E0448
TX15MIT ALPHA1
TX15MIT Z4 FRONT VIDEO/SCART
TX1631 U4W
TX1632 U4
TX1641 U4
TX1642 U4
TX1752 COLD NO LUMA, LOPTX PINS.
TX1752 NO SND WITH TEXT IC171(SAB3035).
TX1752 U5
TX1752 U5 NOISY PSU LO HT, LOPTX
TX1752 U5 SLOW PIC , LOPTX PINS
TX1786
TX1786 Z3
TX1786 Z3T
TX1786 Z3T STR54041+D854
TX2
TX2 ALPHA1
TX2024 U3W
TX2034 U4
TX2112 U5N
TX2112 U5N INT PIC LOPTX RIVETS
TX2112 U5N INT PIC LOSS LOPTX PINS.
TX2112 U5N STBY TX, MUTE ON CHAN CHANGE,MAB8441-T005 MICROCONTROLLER
TX2112(U5N) REMOTE SOUND MAB8441-T005 NLA.
TX211AD2 EURO2
TX2122 DEAD SQUEAL LOPTX TFL14584F
TX2151 DEAD APART FROM LOW TWEATING NOISE HT OK BUT LTS LOW - Q803 2SD1272
TX2151T DEAD CHECK R802 AND R818 IN POWER SUPPLY 150K, 180K
TX2151T FIELD - PARTIAL COLLAPSE 33V TUNING REG IC012
TX2162 U5
TX2172 ALPHA1
TX2175 Z1
TX2178 ALPHA1
TX2195 Z3T
TX21A1 ALPHA2W
TX21AD2
TX21AD2 ALPHA1
TX21AD2 EURO2
TX21AD2 SNOWY PIC C111 0.068UF,
TX21AD2=EURO2
TX21AD2D STBY C804(1UF25V), C806, C807(100UF50V)
TX21AD2DP EURO2L
TX21AD2DP STBY TRIPPING, C804 (1UF, 25V), C806, C807 (100UF/50V)
TX21AD2M EURO2M
TX21AP1 Z8T REMOTE EUR511300
TX21AT1 Z8T 2002 REMOTE EUR511300
TX21AV1 Z082PF (DAEWOO CP082, K30 DECK) REMOTE EUR51941
TX21CK1 STBY R804(100K)
TX21CK1 Z8
TX21GV1 COMBI HOT REMOTE LOCKS UP, IR SENSOR KRT30.
TX21GV1 COMBI DAEWOO DEAD FUSE C835(2N2630V)
TX21GV1 COMBI DAEWOO DEAD PULSING LED/RELAY,C840(47UF25V) STBY PSU
TX21GV1 COMBI INT SHUTS OFF/ON ,IC1807(TOP210) CHOPPER CTRL.
TX21GV1 COMBI INT SHUTS OFF/ON ,ON/OFF SWITCH VERY AWKWARD
TX21GV1 COMBI STBY LED BLINKS C840(47UF25V)
TX21GV1 DAEWOO COMBI
TX21GV1 DEAD C885(2N2F630V)
TX21GV1 DEAD,I807(TOP210) STBY CHOPPER,C840
TX21GV1 STBY LEDS/RELAYS PULSE,C840(47UF25V)
TX21GV1 TEST MODE PRESS SET VOL-+REMOTE STATUS.
TX21GV1 Z421V (DAEWOO CP420, K-MECHA DECK)
TX21GV1 Z421V CHASSIS COMBI.
TX21GV1 Z421V DEAD,F801 (4 amp) C835 (2200pF 630v),C819 STR-S5707 chopper
TX21GV1 Z421V NO R/C AFT 2 HRS REPLACE IR SENSOR KRT30 FROM TYPE 36 TO 3F
TX21JT1 Z7
TX21JT2 ZM3L (ORION CHASSIS) 2003, REMOTE EUR511300 PCB MARKED TMB553A, MICRO TLOPTR Q401 2SD2499 PSU Q511 2SK2647
TX21K1T Z7
TX21K2T Z7
TX21M Z4
TX21M1R Z4
TX21M1T PIC SIDE SHIFTED C503(0U01F).
TX21M1T Z4
TX21M1T Z4 DEAD FAINT WHISTLE D654(R2KN)+LOPTX(TLF15621F.)
TX21M1T Z4 MEMORY STORE ALL POSITIONS, TEXT PCB LINK J10 JOINTS
TX21M1T(Z4)R802(4R7)+STR54041M+Q801+Q802(2SD965/BC337).+D854+C809(100)+C808(10).
TX21M2T
TX21M2T ALPHA1
TX21M2T Z4
TX21M2T Z4 REMOTE TNQ8E0448
TX21M2T/B 2SD965=40V NPN 0.75W
TX21M2T/B INT PIC/SND LINE DRV TX(T351)
TX21MD1
TX21MD1 EURO2 INT SW TO STBY ON BRIGHT SCENES EPROM IC1203 X24C0803AF AND EPROM IC1202 27C010-800SA.
TX21MD1 EURO2L
TX21MD1 FIELD BOUNCE EPROM IC1203 PART NUMBER X24C0803AF, EPROM PART NUMBER 27C010-800SA
TX21MD1 INT REVERTS TO STBY EAROM 8 LEGGED DEVICE BUT REPLACEMENT WILL ONLY WORK PROPERLY WITH LATEST VERSION OF SOFTWARE IC
TX21MD1 NO SND OR PIC - TAPPING TUNER MAY BRIEFLY CURE SM RESISTORS X 2 820R IN TUNER DRY JOINTS OR FELL OFF
TX21MD1 REVERTS TO STBY WHEN COLD & INT SND MSP IC ON TUNER/NICAM PCB
TX21MD1 SLOW START UP & INT SND MSP IC ON TUNER/NICAM PCB
TX21MD1 TUNING INT 2 X 82R SM RES IN THE TUNER, IN LINE WITH PINS 3 & 5 OF IC TYPE MT02B.
TX21MD1, TX21AD2, TX25MD1, TX28LD1, TX25AD1, TX25AD1DP, TX29AD1, & TX29AD1DP EURO2
TX21MD1B
TX21MD3
TX21MD3 BLANK SCREEN WITH SMALL WHITE DASHES. OSD, TXT & SND OK IC601 (VDP3108APPA1)
TX21MD3 EURO2
TX21MD3 EURO2M
TX21MD4 EURO4
TX21MD4 EURO4 REMOTE EUR511200
TX21MIT Z4 INT COLOR 0.01UF SURFACE-MOUNTED COUPLING CAP, C2651.
TX21MIT Z4 NO SYNC MAB8461-PW216 ON TEXT PCB
TX21MK1 EURO4 REMOTE EUR511200
TX21S1 Z5 INT BLACK LINES , TUNER UNIT,PINS?
TX21S1 Z5 LINES THICK ON SCRN, TUNER, RESOLDER EARTHLING STRIPS AND CASING TO THE PCB INSIDE
TX21S1R ALPHA1
TX21S1T ALPHA1 Z5
TX21S1T FIELD V/LOW IC012 (30V REG).
TX21S1T LO FIELD 33V TUNING VOLTAGE REGULATOR IC012
TX21S1T WARM EXCESS BRILL,LOPTX A1'S
TX21S1T Z5 ,TICKING STR51424M
TX21S1T Z5 NO PIC SND OK, Q504.
TX21S1T Z5 REMOTE TNQ8E0461
TX21S1T Z5 SND OK NO PIC/BLANK RASTER Q504 BC847BSM PINS.
TX21S1T/BH TO TUNE "F" BUTTON ON TV TIL "TUNING" SHOWS - THEN PRES "^" KEY. ENTER CHAN NO. BY "C47". & PRESS "S" TO STORE. EXIT "F"
TX21S3 Z7
TX21S3T
TX21S3T Z7 SEE Z7 FAULTS BELOW
TX21S3T DEAD - NO HT TO IC601 D861
TX21S3T NEGATIVE PIC /AGC ON TUNER ,SCART PICS OK EEPROM (STORE PREVIOUS DATA VALUES AND THEN ENTER INTO NEW CHIP
TX21S3T NO LINE DRIVE D861
TX21S3T NO SND - OK THRO SCART I/P NO O/P FROM IC601 - CHIP FAULTY
TX21S3T WHISTLE ONLY DIST LINE DRIVE WFRM - PIN 9 IC601 ONLY 3.7V (8V); D861 1SS133T-77
TX21S3T Z7
TX21S4TL Z7 REMOTE EUR511300
TX21T
TX21T ALPHA2
TX21T1
TX21T1K ALPHA2
TX21T1K GOTO ALPHA2
TX21V1
TX21V1 ALPHA2
TX21V1 ALPHA2 INT NO PIC, THREE PINS OF CONNECTOR B4 HAD CRACKED, RIGHT AT THE FRONT
TX21V1 ALPHA2 NICAM SND 0.01UF C2549 CONNECTED TO PIN 9 OF IC2502,
TX21V1 ALPHA2 NO LINE DRIVE R851(2R2)
TX21V1 ALPHA3 DARK BLANK PIC NO SND , MAB8461PW13S CHIP IC3507
TX21V1 APLHA2 NO NICAM C2549
TX21V1 BLANK RASTER NO OSD IC3507.
TX21V1 BRIGHT RED, COIL IN ANODE LOAD O/C.
TX21V1 NO SND LA4270 AFTER EXTERNAL SPEAKERS FITTED
TX21V1 PUT IN EXTERNAL SPKRS BLEW LA4270 MAX 6W.
TX21V1(ALPHA 2)RED SCREN/FLYBACK LINES ,LITTLE COIL ON CRT BASE PCB
TX21V1RE INITIAL EHT RUSTLE THEN CHAN NO ONLY PSU OK ON BULB, L303 10MH 12V FEED COIL TO CITAC ETC
TX21V2
TX21V2 ALPH4 OSD FAULT/TEXT OK = C3304 (0.01).
TX21V2 ALPHA3 COLD BW STRIPES, ZENER DIODE, D329(MA4068)
TX21V2 ALPHA4
TX21V2 LHS SPKR CRACKLE R2081, A 10KSM ON PCB B,
TX21V2 LOW HT 60V CHECK LOPTY
TX21V2 TRIPS AT SW ON - EHT COMES UP BRIEFLY STR54041M IN PSU
TX21V2BC ALPHA1
TX21VS ALPHA4
TX2200 U4 LOPTX=TLF14521F=HR7257
TX2200 DEAD LO HT 121VN LOPTX.
TX2200 DEAD PSU NOISE NO LINE DRV, R513(1K).
TX2200 U4
TX2200 U4 DEAD PSU NOISE, LOPTX+LINE DRIVER TRANSISTOR Q501 + R513 1K
TX2230 U4
TX2231 U4
TX2234 DEAD LED='00', C808(47UF).
TX2234 U4W
TX2244 U4W
TX2284 U3W
TX2450
TX2450 U5W
TX2450 U5W
TX2461
TX2461 LOPTX = TLF14592F HR7260 .
TX2461 U5W
TX2464
TX2464 U5
TX2470 ALPHA1W
TX2470 RAGGED VERTICALS, PSU NOISE,C808(10UF, 50V)
TX2472
TX2472 ALPHA1W
TX2472 ALPHA1X
TX2480
TX2480 ALPHA1
TX2482 SEE ALPHA1
TX2482 ALPHA1
TX2482 DEAD - LOPTR REPLACED LOPTR, R567 1A CCT PROT , 1R2 2W RESISTOR FROM S3 ON SEC OF SMPS TRFMR (27V DRIVER SUPPLY)
TX2488 ALPHA1
TX2492
TX2492 SEE ALPHA1W
TX2492 ALPHA1W
TX24A1
TX24A1 SEE ALPHA2
TX24A1 ALPHA1
TX24A1 ALPHA2
TX24A1 NO SND/VIS - CHAN NO. DISPLAYED IC801 STR54041 - & CHECK DRY JOINTS
TX24A1C ALPHA1
TX24AI ALPHA2W
TX24DX1
TX24DX1 EURO4 GOTO EURO4
TX24DX1 EURO4 REMOTE EUR511210
TX24DX1(EURO4)INT DEAD/STBY D869
TX24MD1
TX24MD1 EURO2
TX24PS1 DEAD R813(3R3),C821(220UF400V)
TX24PS1 EURO10
TX24T ALPHA2W
TX24T1
TX24T1 ALPHA2W
TX24T1 BLANK UNFOCUSSED RASTER? - SND OK L353 ON CRT BASE
TX24W1
TX24W1 ALPHA2W
TX24W1D
TX251XDP ALPHA1
TX2570 WHISLE LOW HT LOPTX+LOPTR(2SD1441)+220UF400V.
TX25A1 DARK BLANK RASTER, C1251(10NF).
TX25A1 TEXT RANDOM DISPLAYS, C35111(220PF).
TX25A2 BAD TEXT, 220UF C3511 IN THE 6MZH PHASE CONTROL CIRCUIT
TX25A2 ALPHA3
TX25A2 TOPTEL NO GOOD.
TX25A2X ALPHA 3 NO COLOUR, 0.01UF CERAMIC FROM PIN 14 (LABELLED DC FEEDBACK) IC601
TX25A2X ALPHA3
TX25A2X NO TEXT CHECK C3517 100NFD50V
TX25A3 EURO1
TX25A3 EURO1 DEAD D536,C593(4U7F63V)
TX25A3 STBY FIELD IC,TDA8175 NLA,MOD KIT RUBBISH
TX25AD1 DEAD 3.15AH CAUSE DEGAUSS POSISTOR
TX25AD1 EURO2S
TX25AD1DP
TX25AD1DP DARK PIC WITH SPARKING CHECK BRIGHTNESS CONTROL ON CRT BASE
TX25AD1DP EURO2
TX25AD1DP EURO2 COLOURED SNOW,VDP3108,KITVDP3108AAP1
TX25AD1DP EURO2S
TX25AD1DP IF EEPROM REPLACED AND TV SWITCHES TO "0" & NO NORMAL STORE PRESS REMOTE STATUS & TV FUNCTION DOWN
TX25AD2
TX25AD2 EURO2S
TX25AD2 NEDIS SELL A TDA8175-KIT IC
TX25AD2DP DEAD NO STBY LIGHT TRY REPLACING IC1801
TX25AD2DP DEAD WITH RED LED PULSING RL6101 COULD BE BURNT UP
TX25AD2DP EURO2 LINE JITTER FIT MOD KIT TXS9EK002-2; DO NOT REPLACE EEPROM OR SND WILL BE LOST (PRO LOGIC VERSION)
TX25AD2DP WONT GO INTO STBY REPLACE Q667 BC547B
TX25AD70F/P EURO3H
TX25BM1 ALPHA2
TX25CK1 Z8
TX25D1/BH STBY TDA8175 FOP CHIP (WITH "3" PREFIX), 1.25A , D456 ZENER 16V MAZ160 & R472 4R7 & 220µ 50V CAP
TX25G1 ALPHA2
TX25LD4DP
TX25LD4DP EURO4
TX25LD4DP EURO4 REMOTE EUR511200
TX25LDM4F EURO4 MULTISTANDARD PAL/SECAM B/G,D/K,I REMOTE EUR511200
TX25MD1
TX25MD1 SEE EURO2/EURO2L
TX25MD1 DEAD FUSE BLOWN REPLACE POSISTOR R808
TX25MD1 DEAD TDA8175 FIELD IC FAULTY & D456 MA2160 ZENER
TX25MD1 EURO2L
TX25MD1 GREEN SPECKLES ON RF AND SCART REPLACE IC601
TX25MD1 RGB LINES AT TOP OF SCREEN REPLACE D454 AND D456
TX25MD1 SND DISTORTED & LOW IC2101 MSP3410-15 64 PIN DEVICE - DON'T ORDER FROM SALI CD -WRONG
TX25MD1/B
TX25MD1/M
TX25MD1/M EURO2L
TX25MD1/M LINE TWITCH - LIKE LOSS OF SYNC REPLACE IC601 @ £27 + VAT
TX25MD3
TX25MD3 SEE EURO2
TX25MD3 GOTO EURO2
TX25MD3 DEAD TICKS,C807(100UF25V)
TX25MD3 DEAD/STBY C807(100UF25V)FL
TX25MD3 EURO2 SEE EURO2 ABOVE
TX25MD3 EURO2M
TX25MD3 GHOST IMAGE ON SCREEN DISCONNECT SCART LEADS
TX25MD3 SLOW START,TUNER UNIT
TX25MD3 SND BUT NO PIC CHECK R507 3.3 OHM
TX25MD4 EURO4
TX25MD4 EURO4 REMOTE EUR511200
TX25MK1 EURO4 GOTO EURO4
TX25MK1 EURO4 1999
TX25MS1 EURO2L
TX25T2
TX25T2 GOTO ALPHA2W
TX25T2 ALPHA2
TX25T2 REPEATED FAILURE OF FIELD CHIP REPLACE SCAN COILS PT NO TZS3EH001
TX25T2 SEE ALPHA2/ALPHA3
TX25T2K
TX25T2K ALPHA1
TX25T2P ALPHA1
TX25W POOR FOCUS LOPTX
TX25W1E R2KL
TX25W2 ALPHA3
TX25W2 ALPHA3 LOPTX HR7294/TLF15548F +R555(1AMP)
TX25W2A ALPHA3
TX25W2A ALPHA3 WITH ASTRA
TX25W2A WITH ASTRA ALPHA3 ,
TX25W2A WITH ASTRA POOR FOCUS LOPTX HR7294
TX25W3
TX25W3 EURO1 USE REMOTE FOR SERVICE ADJUSTMENTS BY PRESSING BASS TO MAX ,
TX25W3 THEN TREBLE TO MIN, RESET AND VOLUME DOWN ON THE TV AT THE SAME TIME.
TX25W3 DEAD - NO START UP C622,C623,C631, C634 & 470K IN PSU & Q624 S2000AF CHOPPER TR E-B
TX25W3 ERURO1
TX25W3 EURO1
TX25W3E
TX25W3E SEE TDA8175 MOD
TX25W3E EURO1
TX25X1 ALPHA4
TX25X1 INT GOES TO STBY CHECK 2 X 270K IN PRI PSU & STR54041
TX25X1 NO SND OR R/C CHECK LEADS IN CONNECTORS E22 & E19 ARE NOT REVERSED
TX25X1DP
TX25X1DP ALPHA4
TX25XD1E EURO2S
TX25XD4 EURO4 REMOTE EUR511200
TX25XD4F EURO4
TX25XD90 EURO5 REMOTE EUR511211
TX25XDP3 EURO2M
TX2636 U4W
TX2646 U4W
TX2656 U5W
TX26AD2 EURO2
TX26LMD70 DEAD POWER BOARD SMPS TNP8EPL60
TX26LXD1 LH18 CHASSIS (LCD TV) 2004 REMOTE EUR7635010
TX26MD1 EURO2L
TX28A1
TX28A1 ALPHA2
TX28A1 ALPHA2W
TX28A1C ALPHA1
TX28A2
TX28A2 ALPHA3
TX28A2X
TX28A2X ALPHA3
TX28A3 EURO1
TX28CK1 Z8
TX28DK1 EURO4 REMOTE EUR511210
TX28DK2 DEAD LOPTR(2SC5517)
TX28DK2 EURO4
TX28DK2 EURO4 REMOTE EUR511210
TX28DK2(EURO 4)NO SURROUND SND TDA2030.Q2701
TX28DT2 EURO4D
TX28DT2 EURO4D PAL-I REMOTE EUR511230
TX28DT2/E EURO4D PAL-I REMOTE EUR511230
TX28DT30 EURO8DH (BUILT-IN DIGITAL RECEIVER)
TX28DT4 EURO10D (BUILT-IN DIGITAL RECEIVER) 2003 AROUND £510 REMOTE EUR511243
TX28DTS3 EURO4DS (BUILT-IN DIGITAL RECEIVER)
TX28DTX1 STBY RESOLDER EVERYWHERE
TX28EX2000 EURO4 MULTISTANDARD PAL/SECAM B/G,D/K,I REMOTE EUR511200
TX28G1
TX28G1 ALPHA2
TX28G1 DEAD STR54041
TX28GI
TX28LD1
TX28LD1 EURO2
TX28LD1 EURO2 SEE EURO2 ABOVE
TX28LD1/M STANDBY CHECK R558 120K FOR
TX28LD1F EURO2L POOR PIC CRT FAULTY
TX28LD4DP EURO4
TX28LD4DP EURO4 REMOTE EUR511200
TX28LDM4F EURO4 MULTISTANDARD PAL/SECAM B/G,D/K,I REMOTE EUR511200
TX28MD3 BLOWS MAINS FUSE REPLACE POSISTOR AND POWER CORD
TX28MD3 EURO2M
TX28MD3L INT FIELD LINES,LA7845N LOC34
TX28MD4 EURO4
TX28MD4 EURO4 GOTO EURO4
TX28MD4 EURO4 REMOTE EUR511200
TX28MK1 EURO4 REMOTE EUR511200
TX28MK1L EURO4
TX28PB50 EURO7 REMOTE EUR511224
TX28PG40 EURO7 REMOTE EUR511224
TX28PG45 EURO7 REMOTE EUR511212A
TX28PK1
TX28PK1 EURO4
TX28PK1 EURO4 REMOTE EUR511210
TX28PK10 EURO5L REMOTE EUR511211
TX28PK100 EURO5
TX28PK2
TX28PK2 3.15AT MOD TO 5A
TX28PK2 EURO4
TX28PK2 EURO4 REMOTE EUR511210
TX28PK25 EURO4H
TX28PK25 EURO4H 100HZ REMOTE EUR511211
TX28PK2E EURO4
TX28PK3L EURO4 REMOTE EUR511210
TX28PL1
TX28PL1 EURO4
TX28PL1 EURO4 SEE EURO4 ABOVE
TX28PL1 EURO4 REMOTE EUR511210
TX28PL10 EURO4H
TX28PL10 EURO4H 100HZ AROUND £660 REMOTE EUR511211
TX28PL20 EURO4H
TX28PL4 EURO4 REMOTE EUR511210
TX28PL4 NO AV3 O/P,IC601
TX28PN1 GP4L
TX28PS1 EURO10 2003 AROUND £450 REMOTE EUR511320
TX28PS12 2003 AROUND £510
TX28PS5 EURO10
TX28W1
TX28W1 ALPHA2W
TX28W2
TX28W2 ALPHA3
TX28W3
TX28W3 DEAD C623 100µ 50V
TX28W3 EURO1
TX28W3 EURO1 NO PIC/SND,C623 R628
TX28W3 PULSING ON & OFF CHECK RIBBON CABLE TO FRONT DRAWER
TX28W3E SEE TDA8175 MOD
TX28X1 ON/OFF KNOB TBX2883901-1
TX28X1 ALPHA4
TX28X1DP ALPHA1
TX28X1DP ALPHA4
TX28X1DP ALPHA4 DEAD NOISE,LOPTR(2SD1557RL),C558(8N2F2KV) CAUSE TDA2579A,STR56041M)
TX28X1DP INT SIGNALS DRY JOINTS TUNER
TX28XD1E EURO2S
TX28XD3 EURO2M
TX28XD4 EURO4 REMOTE EUR511200
TX28XD4 IC2704 TDA2030AV
TX28XD4 SND REAR SPEAKERS PULSING. Q2705(BC847B)
TX28XD5C EURO2S FIELD COLLAPSE TDA8175
TX28XD90 EURO5 REMOTE EUR511211
TX28XDP3 EURO2M
TX29A3
TX29A3 DIST PIC - OFF TUNE EFFECT WITH BLACK DOTS OVER SCREEN IC1601 SAD2140
TX29A3 EURO1
TX29A3 FIELD TWITCH - INT DRY JOINTS FOP CHIP
TX29AD1
TX29AD1 EURO2
TX29AD1 EURO2S
TX29AD10C(F) E2100 NONUK
TX29AD1D ALPHA1 EURO2
TX29AD1DP DEAD WIOTH FUSE BLOWN CHECK POSITOR FOR RATTLE - 96706 (EXPENSIVE)
TX29AD1DP EURO2S
TX29AD1DP INT FIELD - THIN BLACK LINES AT BOTTOM D507 & D508 MA723TA5
TX29AD1DPB
TX29AD1DPB SEE EURO2S
TX29AD2
TX29AD2 EUR02
TX29AD2 EURO2S
TX29AD2 PATTERNING/GHOSTING - LIKE AERIAL MOVING IN WIND IC601 (£30+)
TX29AD20C E2100 NONUK
TX29AD2DP
TX29AD2DP D544 ARCING
TX29AD2DP EURO2
TX29AD2DP EW BENT SIDES ,D544
TX29AD2DP NO SND FROM CENTRE OR SURROUND SPEAKERS REPLACE IC205 TDA2030A
TX29AD2DP NO SND IC466 (LA4282) R688 (0.1R), IC2513 (SC442013B) ON THE DSP BOARD - IC466 IS THE CAUSE
TX29AD2DP SERVICE MODE BASS=MAX,TREBLE=MIN,"F" ON TV,"VOL-" ON TV/WHILE REMOTE "REVEAL","N" TO EXIT.
TX29AD2DP SERVICE MODE,BASS MAX,TREB MIN,"F",(TV VOL-/"REVEAL"),N=EXIT
TX29AD2DP TOP LINE PAIRING D508 MA723TA5 FUSSY
TX29AD30C E2100 NONUK
TX29AD70 EURO3H
TX29ADI EURO2 DARK, DIAGONAL BLACK LINES, TPU3040-18 TELETEXT PROCESSOR CHIP. IC1701
TX29ADP2DP NO SURROUND SND REPLACE IC506 TDA2030
TX29AK1 EURO4 REMOTE EUR511200
TX29AK10P EURO5 REMOTE EUR511211
TX3
TX3 ALPHA ? HI HT (119V NORMAL)C806(10UF50V) USED 47UF63V RIGHT IN CORNER.
TX3 ALPHA1
TX3 ALPHA2
TX3 DEAD STR54041+10UF.
TX3 FIELD COLLAPSE TDA3653C +C808 10UF.
TX31GV1 COMBI,INTSND ,C613 IN VCR AUDIO
TX32DH40 EURO8DH (BUILT-IN DIGITAL RECEIVER)
TX32DK1 BLUE SCREEN, CRT FAULTY (BADGED PANA BUT PHILIPS UNDER LABEL)
TX32DK1 CYAN SCREEN, CRT FAULTY (œ300)
TX32DK1 DEAD LOPTR(2SD1577) CAUSE CRT
TX32DK1 EURO4 REMOTE EUR511210
TX32DK1 EXCESS BRILL R558(120K),C563(22UF250V),C564(2U2F100V)
TX32DK1 INT EXCESS BRILL CRT FAULT
TX32DK1 LOW CONTRAST,IC601,R558(120K)
TX32DK1 MAGENTA SCRN,FLYBACK LINES,PHILIPS CRT(W76ESF031X13)
TX32DK1 NO GREEN,TDA6103Q
TX32DK10 EURO5
TX32DK2 BLUE SCREEN, CRT FAULTY (BADGED PANA BUT PHILIPS UNDER LABEL)
TX32DK2 EURO4 REMOTE EUR511210
TX32DT2 EURO4D
TX32DT2 EURO4D REMOTE EUR511230
TX32DT2 EURO4D STARTS/STBY,C454(22NF50V)SM CHIP CAP FROM PIN 7 OF OP/CHIP
TX32DT30 EURO8DH (BUILT-IN DIGITAL RECEIVER)
TX32DT4 EURO10D (BUILT-IN DIGITAL RECEIVER) REMOTE EUR511243
TX32DTS3 EURO4DS (BUILT-IN DIGITAL RECEIVER)
TX32LXD1 LCD DEAD 2 PSU'S STRL351LF428,R808(5R6)
TX32LXD1 LH18 CHASSIS (LCD TV) 2004 REMOTE EUR7635010
TX32LXD1 STBY,LITE SURGE,R916(2A5)
TX32LXD55 LCD SCREEN DAMAGE
TX32PB50 EURO7
TX32PB50(N) EURO7 REMOTE EUR511224
TX32PD30 BLANK RASTER,NO SND,OSD OK,IC3001(9V REG)
TX32PD30 GP1 , 100HZ
TX32PD30 GP1 GOTO GP1
TX32PD30 GP1 DEAD HT AT 30V C851 SHORT .1 AT 400V LOCATED BY IC851
TX32PF10 EURO4 WARM BAD CONVERGENCE, CRT FAULTY
TX32PF10 EURO5 REMOTE EUR511220
TX32PG30 EURO7 DEAD LOPTR(2SC55591000RK)
TX32PG30 EURO7 INT ODD COLOR, DIG BOARD EXCHANGE UNIT
TX32PG30 EURO7 REMOTE EUR511212A
TX32PG30 STBY LC1118
TX32PG50 EURO7 REMOTE EUR511224
TX32PH40 EURO7P 2002 REMOTE EUR511224
TX32PK1
TX32PK1 EURO4
TX32PK1 EURO4 ODD CONVERGENCE,CRT FAULTY(W76EKW10X21)
TX32PK1 EURO4 REMOTE EUR511210
TX32PK2
TX32PK2 DARK PIC C360(27NF2KV) LO A1'S
TX32PK2 ARK PIC, LO A1'S CAPS ON CRT BASE PCB
TX32PK2 EURO4 REMOTE EUR511210
TX32PK2 SEE EURO4 ABOVE
TX32PK20 EURO5 REMOTE EUR511211
TX32PK25 EURO4H
TX32PK25 EURO4H 100HZ REMOTE EUR511211
TX32PK2C EURO4, NO REAR SND, IC2704(TDA2030AV).
TX32PK3 EURO4 EHT SURGE/STBY C454(220NF)
TX32PK3 EURO4 REMOTE EUR511210
TX32PK3 INT STBY C454(22NF SM)
TX32PL1 EURO4
TX32PL1 EURO4 REMOTE EUR511210
TX32PL10 EURO4H
TX32PL10 EURO4H 100HZ AROUND £900 REMOTE EUR511211
TX32PL10 WARM NO SND,Q850
TX32PL20 EURO4H
TX32PL4 EURO4
TX32PL4 EURO4 REMOTE EUR511210
TX32PM1 LO WIDTH/EW BENT SIDES,Q701(2SK2049),R706(10R),L701(8.2MH),R713(8R2)
TX32PM1 DEAD LED FLASHES, Q850(2SA1668)
TX32PM1 GP4 LINE DOWN MIDDLE,SCAN COIL PINS
TX32PS1 EURO10 2003 REMOTE EUR511320
TX32PS12 EURO9L
TX32PS5 EURO10
TX3300 U4
TX3370GR ALPHA1
TX33A1 ALPHA2W
TX33A1G ALPHA2
TX33A1G ALPHA2 NO PIC/SND SOME LIGHT,,L853
TX33A2 ALPHA3
TX33A2, ALPHA3
TX33AK10 SEE EURO5
TX33AK10 EURO5 BLURRY PIC, EEPROM
TX33AK10 EURO5 ODD STREAKY PIC ,EEPROM RESET
TX33AK10 EURO5 REMOTE EUR511211
TX33AK10 EURO5 RESET EEPROM PRESS TV VOL- WHILE PRESSING REMOTE STATUS BUTTON(BUTTON HAS +)
TX33AK10 UERO5 WARM DARK PIC,C395,C386,C397 ON CRT BASE PCB
TX33AK10(EURO5) ODD POOR PIC, EEPROM
TX33AK10(EURO5)RESET EEPROM, PRESS TV VOL-/REMOTE STATUS+
TX33PF10 EURO5 LO AV SND,RUN SELF CHECK
TX36DT35 EURO8 2002 REMOTE EUR511241
TX36PB50 NO SND,RESOLDER IC2510,IC2501,IC2504 ON DP PCB
TX36PB50(N) EURO7 REMOTE EUR511224
TX36PD30 GP1 , 100HZ
TX36PD30 INT BRILL/PIC,SND OK,IC832(12V REG)
TX36PF10 EURO5 REMOTE EUR511220
TX36PG50 EURO7 REMOTE EUR511224
TX36PL30 EURO7 REMOTE EUR511212A
TX37A2 ALPHA3
TX37A2 LO BRILL Q355.
TX37A2 LOW BRIGHTNESS + GETTING LOWER Q355 ON TUBE BASE
TX37A2G ALPHA3
TX37LZD70 37 INCH LCD TV
TX42PT10 NO PIC ,TTEXT OK, PRESS F(TV) HOLD V-(TV) WHILE PRESS REM STATUS,POWER OFF.
TX47PT1(PROJECTOR) EURO5VP REMOTE EUR511220
TX47PT10 (PROJECTOR) EURO7VP
TX5500 U5
TXC21 U4
TXC21 U4 DEAD R1351(0R68) ON FRONT PCB
TXC22 LOPTX=TLF14584F=HR7268.
TXC22 U5
TXC71
TXC71 ALPHA1W
TXC74
TXC74 ALPHA1
TXC74 ALPHA1W
TXC78
TXC78 ALPHA1W
TXC78 CHANNEL LIGHTS ON BUT SET JUST WHISTLES NO LINE DRIVE IC101 TDA4505-M1
TXC84 ALPHA2
TXC88 ALPHA2
TXG10 AC-1
TXG10 AC1 MULTISYSTEM
TXG10 TRIPS 12V , IF 6/7V CHECK IC855 LM317 ON MAIN PCB .
TXG29 INT BLANK RASTER,TDA8350Q
TXS3T Z7
TXW-28-R4 TRIPPING LOPTR BU250BAX USE 2SD1577LB AS REPLACEMENT
TXW28D1F E2100 NONUK
TXW28D2 EURO3HW
TXW28D2DB FIELD COLLAPSE,R568(33R) F531(T1A) IC451(TDA8350Q)
TXW28D5F/P EURO5
TXW28R3 EURO3
TXW28R3 EURO3W
TXW28R3 SERVICE MODE BASS=MAX,TREBLE=MIN' REMOTE REVEAL' OR ' INDEX' VOL+,RED,"N"
TXW28R4
TXW28R4 EURO4 GOTO EURO4
TXW28R4 AV3 FOLDOVER EEPROM (XGL2-01LA)
TXW28R4 BLANK RASTERIC1101,R1116(100R),R1121(100R)
TXW28R4 BRIGHT ONE COLOR , CRT
TXW28R4 COLD NO TEXT IC1101,X1101(6MHZ).C1103 C1104(22PF)
TXW28R4 DEAD EEPROM(27C2001-F18)
TXW28R4 DEAD EXCEPT WHEN EXTERNAL SPKRS REMOVED,R2702(150K)
TXW28R4 EW BENT SIDES,R701(100R),L701,IC701,Q701
TXW28R4 INT SOUND WHISTLE, EEPROM(27C2001-F18)
TXW28R4 INT STBY/ON AGAIN EEPROM
TXW28R4 JUST SNOW TUNER UNIT(ENG275066) OR EPROM(XGL2-01LA),R112(100R),R113(22K)
TXW28R4 NO GREEN/BLUE TDA6103Q-N3
TXW28R4 NO PIC OR OSD,IC1101,IC601
TXW28R4 NO PIC/SND
TXW28R4 NO RED,Q351(2SA1767) OR CRT
TXW28R4 NO SCART COLOR,EEPROM(XGL2-01LA)
TXW28R4 NO SCART PIC,IC601,IC3401(TEA2114)
TXW28R4 NO SND,LA4282,C264(2200UF50V)
TXW28R4 ONLY SOME CHANNELS,TUUNER UNIT
TXW28R4 POOR CONTRAST R558(12-K),IC601
TXW28R4 RESET EEPROM PRESS BOTH STATUS(INFO)/ AND "P"
TXW28R4 SND CRACLES IC251(LA4282)
TXW28R4 STBY LOPTR (BU2508AXLB/2SD1577LB)
TXW28R4 STBY PULSING EEPROM
TXW28R4 SURGE/STBY IC601
TXW28R4 SURROUND SND HOT/SMELLS D2716 D2717,R2702(150K),TDA2030AN STR10006,IC2102(MSP3410D)
TXW28R4 WARM STBY IC451
TXW28R4(DP) EURO4 REMOTE EUR511210
TXW28R4DP EURO4
TXW32D2 EURO3HW
TXW32D2DP EURO-3HW
TXW32D3DP/L EURO3HW
TXW32D4DP EURO5 REMOTE EUR511211
TXW32D5F/P EURO5
TXW32R4(DP) EURO4 REMOTE EUR511210
TXW32R4DP EURO4
TXW36D3DP/L EURO3HWS
TYSU1 ALPHA1
TYSU2 ALPHA1
TYSU3 ALPHA1
U1
U1 DEAD Q801 BU326 CHOPPER TR FAULTY - CHECKED OK ON METER
U1 INT FIELD COLLAPSE DRY JOINTS TRS 454 & 455
U1 NO COLOR - INTERMITTENT. INTERMITTENT CUSTOMER COLOR CONTROL.
U1 NO RASTER - EHT OK. D818.
U1 NO RASTER EHT OK, D818.
U1 NO SND/RASTER R810.
U1 SND - NO SND OR RASTER. R810.
U2
U2 STANDBY. D852 OR D853 ( BY298 ) LEAKY , BU208.
U2 FIELD COLLAPSE Q403 (DARLINGTON TR) 2SD837 - BD645 WORKS
U2 FRAME - TOP FOLDOVER IF ADJ A1 CONTROL. FRAME IC TDA1106.
U2 HI BRILL+LINE FREG OFF, C856(10UF).
U2 LINES/INTERFERENCE ON PIC C854
U2 NO BRIGHTNESS. BU208.
U2 NO PIC - CRT CUT OFF. 2X ZENERS 6.2V IN REGULATOR BASE CCT.
U2 NO PIC EHT OK, TDA1106 FIELD.
U2 POOR PIC R555 NO WORKING, R305(820K).
U2 SND - LEVEL AFFECTED BY CONTRAST CONTROL. C857 ( 47U F )
U2 SQEALING/LINE TEARING/CORRUGATED VERTS C809 1µ 250V
U2 STANDBY - STANDBY. D552 ( TVSC2715M ) .
U2 STANDBY - STANDBY. PSU D852/3 , Q501 LINE DRIVE TRANSISTOR , LOPTX.
U2 STBY D552(TVS2715M) O/C.
U2 SYNC LINE/FIELD C854.
U2 WIDTH & HIGHT REDUCED. C371 ( 100UF 240V ) IN MIDDLE OF BOARD.
U3
U3
U3 COMES ON IN STANDBY IF ON/OFF SWITCH IS USED. RELAY RY1001 CARBONISED CONTACTS.
U3 DEAD PSU SQUEAL,LOPTX
U3 FIELD - 1/2 PIC Q402 2SD856 - USED TIP41C
U3 FIELD COLLAPSE Q402 Q403,D406 D407.
U3 FIELD COLLAPSE REPLACED FIELD O/P TRS BUT RAN HOT - D407 1N4148
U3 INT STBY RELAY
U3 LO WIDTH+HI BRILL RHS, D522+D523.
U3 RAGGED VERTICALS,PSU SQUEAL, C809(1UF350V)
U3 STBY RELAY RY10001
U3 STBY, RELAY CONTACTS RY1001.
U3 TRIPS TO STBY AFT 1 SEC HT SMOOTHER C808 220µ 400V
U3 WHISTLES/SCREECHES AT SW ON WITH BLACK LINES C809 1µ 350V, C853 100µ 250V
U3 WHISTLING & RINGING VERTS C853 100µ 250V
U3W CHANNELS - DIFFICULTY SELECTING CHANNELS. IC TMS3452N2L.
U3W CHANNELS - NOT STORING CHANNELS. IC TMS3452N2L.
U3W DARK PIC WITH FIELD FOLDOVER Q552 12V REG
U3W EW RASTER Q753 .
U3W FIELD COLLAPSEE 2SD837 DARLINGTON Q403,
U3W LACK OF WIDTH & BRIGHTER ON RIGHT HAND SIDE. EW MODULATOR DIODES D552 ( TVSC2715M ) , D553 ( TVSC2406M )
U3W LINE TEARING C853(100UF)+C854(47UF).
U3W LINE TEARING. C853 ( 100U F ) , C854 ( 47U F )
U3W NO SIGS OR CHAN DISPLAY FROM COLD TMS3453N2L MEMORY CHIP (£31 FROM WVE)
U3W SQUEALING+LINE TEARING C809(1UF).
U3W VERTICALS CORRUGATED - NOISE AT SWITCH ON. C809 ( 1U F 350V )
U4
U4
U4 90 DEAD 8R2 C555 SN76622AN
U4 BLANK RASTER & NO SND. L102 .
U4 BLANK RASTER NO SND, L102 O/C.
U4 BLANK SILENT RASTER, R555(1R5)+D555 S/C.
U4 BRILL VARIES C555(10UF).
U4 COMES ON IN STANDBY IF ON/OFF SWITCH IS USED. RELAY RY1001 CARBONISED CONTACTS.
U4 COMES ON THEN SHUTS OFF C808 47U 16V
U4 DEAD - NO EHT - DIPLAY = 00 ; HT = 60V LOPTX U/S THO' CHECKED OK ON TESTER - NLA?
U4 DEAD LO HT, PSU NOISE,C854(100UF250V),LOPTX,D557(BY299)
U4 DEAD PSU NOISE R513(1K)
U4 DEAD R551,C555(10UF250V)
U4 DEAD WHISTLE T551 S/C.
U4 FLYBACK LINES ON BRIGHT RASTER (TEXT SETS), IC5002(5VREG)+R559(1R2).
U4 INT PIC BOWING SIDES ,Q753(2SD1265).
U4 INT STBY RELAY
U4 INT STBY START, RY1001 CONTACTS.
U4 INT TUNING /NO SEARCH SAB3035.
U4 MEMORY LOSS - INTERMITTENT. RE-SOLDER CRYSTALS ASSOCIATED WITH MAB8440 & SAB3055.
U4 NO HTRS R557(2R7).
U4 NO PIC/NO SND, HT TOO HI ,C808(47UF16V)
U4 NO R/C OPERATION NO 12V TO R/C RX; R1336 150R ; & REPLACE 12V ZENER
U4 NO SND & BLANK RASTER. L102 .
U4 NO SND 10UF, 16V CAPACITOR C513
U4 NO SND OR SYNC. DJ ON PINS OF SOCKET Z6.
U4 NO SND SN76622AN.
U4 NO SND+NO SYNC, Z6 SOCKET.
U4 NO SOUND/NO SEARCH STOP Q1212+C513 10UF16V).
U4 NO VOL CONTROL, SN76730N , SWAP PINS 14/15+100R ACROSS R1261.
U4 ONE SIDE BRIGHTER C356(1UF) ON CRT BASE PANEL.
U4 POOR SEARCH,MICROCOMPUTER OR IC1204.
U4 RANDOM CHAN CHANGE/VOL ,IC1101(TDA3048B)+D1101(PH302)+C1108(10UF).
U4 SET STARTS UP BUT SHUTS DOWN INSTANTLY C808 47UF 16V OC
U4 STANDBY - COMES ON IN STANDBY. RELAY RY1001 CARBONISED CONTACTS.
U4 STBY Q551(2SD1439RL) OR IC501(AN5435).
U4 STBY RELAY RY1001
U4 SURGE/OFF C808 47UF, 16V
U4 SYNC - NO SYNC OR SND. DJ ON PINS OF SOCKET Z6.
U4 TUNING - INTERMITTENT. IC SAB3035 IC DRY JOINTED.
U4 TUNING INT +NO SEARCH, SAB3035.
U4W DISPLAY - SHOWS 00 - NO SND OR PIC. HT SET TO HIGH C808 ( 47U F , 25V ) IN PSU.
U4W INT STBY C808. 47UF 25V.
U4W SQUEALING - LOW HT. C854 ( 100U F , 250V ) , D557 ( BY299 ) , LAST LOPTX.
U5
U5 BLANK RASTER - SND OK - BRIGHTNESS WORKS TDA3562A U/S
U5 CHANNELS - NO CHANNEL CHANGE DRYS ON Q551.
U5 CHANNELS - POOR CHANNEL CHANGE & PIC. DRYS ON XTAL X171 , FAULTY IC171.
U5 COLD LINE PAIRING C808 47UF, 16V
U5 DARK PIC TDA3562A
U5 DARK/NO PIC TFK/PHILIPS TDA3562AP
U5 DEAD - CHOPPER TR BLOWS R803 330K
U5 DEAD LOPTX
U5 DEAD PSU SQUEAL LOPTX
U5 DEAD Q551 +IC501(TDA2579).
U5 DEAD Q551 LOPTR & IC501 TDA2579 TIMEBASE GEN CHIP FAULTY
U5 E-W FAULTY Q753 EW DRIVER 2SD1265P DRY JOINTS OR FAULTY
U5 EXCESS BRILL FLYBACK, (INT) LOPTX T551.
U5 FIELD COLLAPSE E7 CONNECTOR.
U5 HT VARIES D806(RD6.2EB2 ZENER).
U5 HT VOLTS VARIES D806 ZENER RD6-2EB2
U5 INT DEAD DRY JOINTS SCAN COIL PLUG
U5 INT DEAD WITH WHINE DRY JOINTS LOPTR -EMITTER
U5 INT LINE SYNC, IC501(TDA2579).
U5 INT LOSS OF LINE SYNC TDA2579 IC501
U5 INT LOSS OF PIC IC5002 SAA5240 ON TXT PCB
U5 LINE PAIRING FOR FIRST FEW MINS AT SW ON C808 47µ 16V IN PSU
U5 LINE WHISTLE/PAIRING C808(47UF16V).
U5 LINES WHEN CHAN CHANGING & DIFFICULT TO TUNE CHECK IC171 SAB3035 & XTAL X171
U5 LOPTX =TLF14586F=HR7268
U5 NO COL TDA3562A COL DEC CHIP
U5 NO CRT HTRS T551 LOPTX PINS.
U5 NO LINE DRV R530 WWOUND.
U5 NO LUMA/GOOD CHROMA TDA3562A.
U5 NO LUMINANCE FOR FIRST 30MINS LOPT DRY JOINTED
U5 NO LUMINANCE FOR FIRST HALF HOUR OR JUST INT DRY JOINTS LOPTX - YOU WOULDN'T BELIEVE IT WITH YOUR EYES
U5 NO PIC INT IC502(SAA5240) ON TEXT PCB.
U5 NO PIC TDA3562A COL DEC CHIP
U5 NO SND ON ONE CHANNEL - INTERMITTENT. 1MR RESISTOR UNDER PCB FROM PIN 18 OF IC501 TO .
U5 NO SND ON TELETEXT. IC171 ( SAB3035 )
U5 NO SND ON TXT IC171 SAB3035
U5 NO SND OR PIC CHANNEL LEDS WORKING, IC171(SAB3035).
U5 NO TUNING+NO CHANNEL LEDS C1214 ON 'M' PANEL.
U5 SLOW STARTUP OF PIC. DRYS ON LOPTX.
U5 SQUEALS HT LOW AT 55V LOPT INTERNAL SC
U5 STBY IC1203 ON 'M' PANEL.
U5 TRIPS TO STBY AFT 1 SEC STBY VOLTS LOW DUE TO 1000µ SMOOTHER
U5 TUNER DRIFT IC171(SAB3035) + TUNER.
U5 UNABLE TO TUNE X171 PINS.
U5 VERY DARK, TDA3562A(PHILIPS TYPE BEST/TDK.
U5 VERY SLOW START, LOPTX PINS.
U5 WARM BLACK LINES ACROSS PIC IC171(SAB3035).
U5N DEAD WITH WHINE LOPTX U/S - CODE TLF14586F - CHECK POLARITY OF FBACK WINDING WHEN REFITTING
U5N SND MUTES FOR 5-20 SECS ON CHAN CHANGE SUSPECT MAB8441-T005 MICRO BUT NO LONGER AVAILABLE
U5N SND MUTES TOO LONG WHEN CHANGING STATIONS ( UPTO MAB8441-T005 US ( NLA )
U5W BENT SIDES,Q753(2SD1265 NPN PLASTC BODY 60V 4A)
U5W DEAD NOISY, LOPTX+ Q551, 2SD1441RL 150VN
U5W DEAD Q803+R803(330K).
U5W HI HT C808(47UF16V) BLOWS LOPTR 2SD1441+D854.
U5W LO HT 150VN 100UF250V
U5W NO PIC RU3B RECTIFIER D852
U5W NO PIC, WHINING & "0" IN DISPLAY HT PRESENT AT LOPTR, NO 26V AS D852 RU3B WAS
U5W ODD COLOR DEGAUSSING POSISTOR. 96009
U5W POSISTOR.
U5W WHINE+NO PIC NO 26V D852(RU3B) O/C.
W28
W28R4DP EURO4,LOPTR(BU2508AXLB) SEE MOD KIT
W28R4DP LINE MOD KIT FROM PANASONIC/SEME
Z1 SEE TV MAG MARCH 1996
Z1 3.15AT+DEGAUSS POS.
Z1 BRIGHT PIC WITH FB LINES & DARK SHADOW ON LH SIDE C554 10µ 250V
Z1 DEAD - NO SECONDARY VOLTS FROM PSU R811 CURRENT SAMPLING RES 0R56 (MISPRINT IN CCT GIVES VALUE AS 56R)
Z1 DEAD POWER WHINE , D854(R2G)+STR54041M.
Z1 DEAD WITH WHINE FROM PSU D854 R2G PROT DIODE IN 103V LINE - IC801 STR55041-M CHOPPER CHIP FAULTY
Z1 HOT SCREEN LINES/POOR LUMINANCE Q303(2SC2636).
Z1 LOPTX ARCING(TLF14736F) TC-1465
Z1 NO COLOR DL601 CHROMA DELAY LINE
Z1 NO COLOR TDA3565 DECODER CHIP & ADJ APC CONTROL
Z1 NO COLOUR CHROMA DELAY LINE DL601,IC601(TDA3565),R626(47K)
Z1 NO START UP. LINK J125 BY TUNER JOINT.
Z1 SERVICING THE Z1 SEE TV MAG MARCH 1996
Z1 TC1460/65/70/75 TC1665/75 &TC2175 TVMAG MARCH1996 P321
Z1 UNCONTROLLABLE BRILL TDA3565 DECODER CHIP - PIN 8 AT ZERO (SHOULD BE 2.3V)
Z1 UNSTABLE PIC ON HIGH BRILL C551 4µ7 160V
Z1 VARYING LUM WHEN HEATED Q303 2SC2636
Z1 WARM LINES 2SC2636 Q303,
Z184
Z185 FIELD COLLAPSE,I501
Z185 LO FIELD HEIGHT,ITS IN 16:9 MODE
Z185 LO HEIGHT ADJUST IN SERVICE MODE
Z185 NO STARTION,EEPROM
Z185 SERVICE MODE, CHAN99,SHARP=MINHOLD TV AND REMOTE MUTE,TV/AV=STORE N TO EXIT
Z185 SNOWY PIC,TUNER UNIT
Z3
Z3-T REPLACEMENT OF TDA4505M-N3 YOU CAN USE CHEAPER TDA4505E IF RE-ALIGN AFC COIL ONLY
Z3-T TDA4505M-N3 REPLACEMENT BY TDA4505E RE-ALIGN AFC AS NEC ONLY
Z3
Z3 ARCING INSIDE TUBE STR50103A INT GOING HI HT.
Z3 COLOR MAX- OSD DOES ALTER , D1149 MA165 DIODE
Z3 COLOR AT MAX OSD MOVES D1149 LEAKY
Z3 CUTS OUT ON BRIGHT SCENES R316 47K IN BEAM LIM CCT
Z3 D815 OVERVOLTS 120V ZENNER?. R2G CAUSE STR50103M 3 LONG LEGS
Z3 DEAD - NO VOLTS FROM PSU REMOVE Q806 STBY TR & WIND UP MAINS VIA VARIAC; ALL WORKED OK & Q806 2SA683
Z3 DEAD - STBY ONLY ON HT LINE - D816 R2G OVERVOLTS DIODE - REPLACE STR50103A
Z3 DEAD - STR50103 REPLACED ALSO PROT DIODE AND POSITOR
Z3 DEAD 100V HT PRESENT, NO LINE DRIVE, PROT TR Q451 OPERATING. WHEN REMOVED FIELD COLL . NO 25V TO FIELD CHIP - R467 1R8
Z3 DEAD 2SA683 STBY SWITCHER.
Z3 DEAD 4R7+STR50103M+2SA683+ZENNER(120V)+CHOPTX S/C TWEEN COILS.
Z3 DEAD BUZZ R560(270K) NR LOPTX.
Z3 DEAD D816 REPLACE STR50103 CHOPPER IC
Z3 DEAD D816 R2G STR50103M CHOPPER IC
Z3 DEAD HT LO 35V(113VN),STR50103M(3LONG)R802(330K).
Z3 DEAD INT START D1124(5V1Z).
Z3 DEAD LO HT(103VN)+LO LT(17VN) Q502+R560(270K).
Z3 DEAD NO PSU OUTPUT 2SA683 STBY SWITCH
Z3 DEAD Q806.
Z3 DEAD R2G ZENER D816 + STR50103M CHOPPER CHIP
Z3 DEAD R560(270K),R552(27K)
Z3 DEAD R801 4R7 5W , IC801 STR50103A-M , D816 HT SR2KN PROT DIODE , Q806 STBY SW TR 2SA683 ,,R559 10R 7W , Q551 2SD1439
Z3 DEAD R801+IC801, CAUSED BY Q551.
Z3 DEAD R802(330K).
Z3 DEAD STR50103M+D816(120VZ) BETWEEN CHINA W/WOUNDS.
Z3 DEAD STR54041+D854(R2K AVALANCHE).
Z3 DEAD TRIPPED R560(270K)
Z3 DEAD WHISTLE STR54041+D854 S/C.
Z3 DEAD WHISTLE, FIELD TEST SWITCH GIVES FRAME COLLAPSE.
Z3 DEAD/INT LOW LT (17V NORMAL) HT OK AT 103V = R560(270K)+R467(1R8).
Z3 DEAD/STBY D811 OPTO . TO CHECK, PRI PINS OF OTO COUPLER . ON NORMAL OPERATION 1,2VOLTS ON THE SECONDARY SIDE PINS, 0,6V ON STBY.
Z3 EHT SURGE/DEAD MA2270 ZENER DIODE D4539 CAUSE CRT FLSHOVER
Z3 FAIL TO START - INT, WITH NO R/C OPERATION 5V SUPPLY FROM SMALL TRFMR AT TPE2 = 4.4V; D1124 5V1 ZENER
Z3 FAIL TO START R802 330K - BIAS PROVIDER FOR CHOPPER CHIP
Z3 FAILS TO START R802 ( 330K ) BIAS TO CHOPPER CHIP
Z3 FIELD - REDUCED HEIGHT WITH POOR LIN C404 4µ7 50V
Z3 FIELD BOTTOM CRAMP C458,10UUF, 50V.
Z3 FIELD CRAMP C404 4.7UF, 50V.
Z3 FIELD D4539 S/C ZENER CAUSE CRT SPARK OVER.
Z3 FIELD LIN - TOP STRETCHED & BOTTOM COMPRESSED C458 4µ7 OR 10µ 50V
Z3 FIELD SCAN CRAMPED AT BOTTOM AT SW ON IC4