Press CTRL/F to search this page (no -)
TV MAGAZINE PAGE 758 OCT 2001 "COMET WILL NOT SUPPLY PARTS TO ANYBODY."
COMET GROUP PLC, AFTER-SALES PO BOX 92 ALBA ?
PRESTON PR2 9GY 08706 052 020 , 01132 310 523 FAX 01132311463
BRIDGEND 0845 6007002, HELPLINE 0870.5133191
PRESS CTRL F TO SEARCH THIS PAGE
1403R C SERIES
TUNING IN 1) SELECT CHAN, 2) PRESS RHS BUTTON 3) PRESS P+
4) PRESS VOL+ OR VOL- TILL STATION FOUND 5)PRESS SECOND BUTTON FROM RHS
6) PRESS VOL+ ONCE, THEN VOL- ONCE 7) PRESS SECOND BUTTON FROM RHS.
8) PRESS RHS BUTTON TWICE
ACCESSORIES DIRECT 0870 6052020
'SKY REMOTE CODES 0335 065, 064, 100, 285, 037, 292, 544, 207, 318, 363, 399, 402, 515
110 DEAD , AN5512 2SA1012
110 DEAD,AN5512
11AK19-08A LOPTR(BU2508AF)
11AK19-8 DEAD- NO STBY R806 22K SEE VESTEL
11AK19-8 DEAD R806 22K
11AK19 SERVICE MODE ,INSTALL MENU PRESS 4,7,2,5. WIDTH=28
14" BLANKED 3/4 PIC R83 100R
1400 FIELD COLLAPSE R306 10R BLACK WIRE LINKING CONTROL PCB TO CENTRE OF MAIN PCB
1401 FIELD COLLAPSE C308(TANTALUM) SITUATED BY PIN 29 TA7698
1403
1403 HOTEL MODE MAX SND, HOLD VOLUME DWN AND TURN POWER ON
1403 MAX VOLUME IS LIMITED IN TEST MODE TO EXIT HOLD VOLUME DOWN BUTTON WHILE TURNING ON POWER
1403R GOTO TATUNG.TV.html
1403R C SERIES DEAD 33K DECCA/TATUNG CHASSIS.
1403R DEAD DECCA/TATUNG C SERIES 2*15K.
1404 AFC/FAULT T103 ADJUST.
1404 STRIATIONS C420 ON CRT BASE
1404 TUNING AFC OFF AFC TANK COIL T103
1404 TUNING SLIGHTLY OFF ADJ T103 AFC TANK COIL
1404 TUNING/AFC OFF ADJ T103 AFC TANK COIL
1404(A) ALBA CTV840 ALSO BUSH 1404, HINARY HIT140RC
1405R DEAD 4R7 5W+STR58041+2AT ,NEED REMOTE TO RELEASE STBY
1405R DEAD,Q602 BLOWN APART R601 (4R7), R612 (0R56), Q602(BC639), R607(4R7) STR58041
1405R DEAD,Q602 R601 (4R7), R612 (0R56), Q602 (BC639), R607 (4R7) STR58041
1405R NO CHANNEL CHANGE OR TUNING M34300-502SP
1405R NO RELAY CLICK, MICROPRO/NVRAM (M34300-502SP)/BR9021B.
1405R POOR FOCUS LOPTX 4992-063.
1405R STR58041+2SC2120(BC639).
1405R TOPTEL 013 VOL+CHAN ONLY.
1405R TUNER DRIFT,33V REG IC104,AFC TANK COIL ADJUST.
1408 CP315 DAEWOO
1408 27MEG CRYSTAL
1408 STK73410-II LOPTX=FSA???????
1408 USUAL 27MEG TYPE FAULTS 27MEG CRYSTAL
141 WONT START FROM FRONT REMOTE OK, 220K FRONT PANEL
141 WONT START(WORKS FROM REMOTE) 220K FRONT PANEL
1410 FERGUSON/THOMSON TX805
1410 SEE FERG_TX.TV.html
1410 FERG D14R/T14R TX805
1410 THOMSON TX805
1410 AE SOCKET TN80341700 CPC.
1410 AFC DRIFT, ADJUST MIDDLE PRESET COIL .
1410 BLANK RASTER M52038SP,RT40(68K)
1410 BLOWS 150V ZENER RESOLDER JP17 UNDER LOPTX
1410 DEAD - NO STBY LED RP44 68K PSU
1410 DEAD DP10 AND DP50
1410 DEAD RP41,42 AND 44 68K OHM
1410 DEAD 150V ZENER CAUSE JP17 UNDER LOPTX
1410 DEAD D412
1410 DEAD DP10 DP50
1410 DEAD DP18(BA159)RP68(0R68)
1410 DEAD DP50(BZX85C150V ZENNER) NR FRAME SCAN PLUG CAUSE JP17
1410 DEAD RP41,RP42 RP44 68K/27K WARNING HOLDS CHARGE.
1410 DEAD RP92 0.68
1410 DEAD S2000A , BLOWS AFTER LOPTX AND TRANSISTOR
1410 DEAD S2000A LOPTX
1410 DEAD S2000AF +RP28(2R75W)+DP11(BA157).
1410 DEAD S2000AF LOPTR TP10. RP28 2.7, 5W DP11 BA157
1410 DEAD START UP RES RP44 & SERIES CONNECTED ONES 68K COULD BE
1410 DEAD, 68K +27K RP44,RP41,RP42 FITTED 56K+47K+56K 1WATT.
1410 FERGUSON TX805
1410 FLYBACK LINES RES JP20 33R
1410 INT DEAD 15V SUPPLY RESISTORS
1410 LINE TEARING /SQUEAK CP90 22U 50V IN PSU
1410 LINE TEARING CP90 22UF50V IN PSU
1410 LINE TEARING WITH SQUEAK FROM CHOPPER TRANSFORMER CP90 22UF50V
1410 LOPTX FCV1410E12A=HR7261.
1410 LOW BRILL RT40 68K ON CRT BASE.
1410 POOR SND. RA10(680).
1410 SEE FERG_TX TX805
1410 STBY LOPTX (SAMSUNG TYPE FCV-1410E12)
1410 STBY/TICKING,LOPTX (FCV-1410E12 SAMSUNG) WHITE WIRE ROUTING.
1410 TUNER DRIFT MTM-BG-2024
1410 TUNER UNIT SEME "TUNE8138" œ42.03 /2002
1410 TUNER UNIT MTS80 80341700 ISOLATED AERIAL SOCKET.
1410 TUNING DRIFT. 33V DHO4 ZTK33 NEAR MAIN MICROPRO.
1410 TX805 DEAD RP44
1410 TX805 DEAD RP 41 , 42 , AND 44 150K AND 120K IN PARALLEL.
1410 TX805 DEAD D412 FITTED UNDER HEATSINK
1410 TX805 DEAD DP18(BA159) RP68(0.68OHM)
1410 TX805 DEAD RP92(0R68)
1410 TX805 DEAD TP10 S2000AF, DP10 BYV38 DP50 ZPU150.
1410 TX805 DISTORTED / POOR SND. RA10 IS CORRECT(680R) NOT 6K8.
1410 TX805 FLYBACK LINES. JP20 MARKED AS 680R 33R IN SET. SERIES WITH 100UF.
1410 TX805 INT SHUTTING DOWN OR DEAD 15V SUPPLY RESISTORS
1410 TX805 LOW BRIGHTNESS. RT40 68K GONE HIGH , ON CRT BASE.
1410 TX805 POOR SND , DIST. RA10 IS COECT(680OHM) NOT 6K8.
1410 TX805 SHUTTING DOWN INT. OR DEAD. CK 15V SUPPLY RESISTORS.
1410 TX805 TUNING DRIFTS. 33V DHO4 ZTK33 NEAR MAIN MICRO IC.
1410 WARM LINE TEARING CP900 22UF, 50V IN THE POWER SUPPLY CIRCUIT.
1418R CP325
1420R AFC/AGC SLIGHT TWEAK OF THE HEX CORE IN THE AFC COIL
1425
1425RS SEE DAEWOO CP375
1425RS 120V OK, A1'S LO NO PIC , BLUE DISC CAP
1425RS COLD BOTTOM LINES C308 470UF25V
1425RS CP375
1425RS DAEWOO ,STRS5707 +R807+R804+R806.
1425RS DEAD LOPTX 1142.5077/HR7880
1425RS GOTO DAEWOO.TV.html
1425RS LINES ON BOTTOM OF SCREEN WHEN COLD C308 470UF25V
1425RS NO PIC SND OK C911 ON CRT BASE
1428
1428 DAEWOO CP330 108VN
1428T GOTO CP330
1428T AERIAL SOCKET ONLY.
1428T NO CHANNEL STORE EEPROM(CAT24C08P*)
1428T NO MEMORY STORE TRY COMET 01656 768841.
1428T TICKING,LOPTX(1142.5034/HR7770)
1430
1430 STBY R302 (DC FEED TO PIN 21 IC301)
1430/1404 STRIATIONS C420 ON CRT BASE
1430R ONWA 8214
1430R DEAD 300V OK R906(1K8)
1430R DEAD C904 ACROSS BRIDGE+R901(4R75W).
1430R DEAD CHOP(BU508AT/BU508AF)R902(2R2)C909, C910(47UF50V)
1430R DEAD CHOPTR(BU508AT),R902(2R2),C910(47UF)
1430R DEAD HT OK, R302 6K8 5W LINE DRV.
1430R NO BAR DURING TUNING OR ADJUSTMENTS,BUT FUNCTION WORKS IC602
1430R NO COL & LACK OF HEIGHT R302 6K8 HI RES
1430R NO COL LO HEIGHT R302 6K8
1430R ONWA STBY IC301 PIN 21 TA8718N 9V SUPPLY MISSING - R302 6K8 5W
1430R STBY IC301 TA8718N R302 6K8 5W
1430R STBY R302 FROM PIN 21 IC301)
1430R STRIATIONS C420 ON CRT BASE
1430R TUNES OK BUT NO OSD IC602
1430R/W ONWA
1430RA (ONWA) NO COL, LACK OF HEIGHT/BOTTOM CRAMP HT 112V OK, R302(6K8)
1430RA 1 NO SND NO CURSOR ON THE BARAGRAPH DON'T REPLACE THE EPROM
1430RA 2 DISCONNECT PIN 4 IC601, TURN ON AND TURN UP THE VOLUME
1430RA 3 USING THE REMOTE. WHEN CURSOR AND SND APPEAR, RESOLDER WITHOUT
1430RA 4 TURNING OFF THEN HIT STBY ON THE REMOTE TO SAVE
1430RA LOPTR 2SD1554(47R+D) +2*47UF.
1430RA LOUD VOL ,ONWA CHIP 547A3314
1430RA NO COLOR, LO HEIGHT/BOTTOM CRAMP HT 112VN R302 6K8
1430RA NO PIC ZD301 BZX55B9V1 (9V1 ZENER)
1430RA NO SND 1, NO CURSOR ,DISCONNECT PIN 4 IC601, TURN ON AND TURN UP THE VOLUME
1430RA NO SND 2,USING THE REMOTE. WHEN CURSOR AND SND APPEAR, RESOLDER WITHOUT TURNING OFF THEN HIT STBY
1430RA ONWA NO SND OSD OK, DISCONNECT PIN 1 OF MN1220, PRESS VOL-THEN STORE THEN RESOLDER PIN
1430RA POWER COMES ON BUT NO PIC ZD301 FOR DIODBZX55B9V1 (9.1V)
1430RA(ONWA) NO SND OSD OK, MN1220
1430RW DEAD RELAY CLICKING C915
1430RWA DEAD - TRIPS IF ON/OFF SW HELD IN C909/911 & LOP TR 2SD2499 (2SD1556 IN LIEU)
1430RWA DEAD C909 C911 LOPTR(2SD2499(INT 47R+D)/2SD1556/S2055N)
1435RS DEAD ON/OFF SWITCH(SEMESW795)
1435RS FRAME COLLAPSE R413 6K8
1435RS ONWA PSU
1445RS ORION CHASSIS REMOTE 076R0DG040
1450
1450 STBY D401(RG2)
1450T ONWA
1450T DEAD R404(1R)
1450T BLANK RASTER ZD102
1450T BLANK RASTER, CRACKED PCB FEED TO ZD102.
1450T DEAD 0.47UF500V DISC ACROSS BRIDGE RECT
1450T DEAD HT OK,R323 6K8
1450T DEAD 4N7 500V DISC 4R7 5W
1450T DEAD 4N7F500V +4R75W.
1450T DEAD LO/NO HT R906(1K8) BESIDE POT
1450T LINES DOWN LEFT SIDE OF SCREEN C307 22UF160V
1450T LINES DOWN LHS C307 22UF160V
1450T NO TEXT Q601 FOR DRY JOINTS
1450T OFF BURNING SMELL NO LINE DRIVE FROM AN5601 IC301. R323 8K2 IN START UP SUPPLY TO CHIP
1450T ONWA
1450T ONWA BLANK RASTER CRACKED PRINT REAR EDGE OF PCB REMOVING SUPPLY TO ZD102
1450T ONWA DEAD 4N7 500V DISC CAP ACROSS MAINS RECT & 4R7 5W
1450T ONWA STBY 115V HT PRESENT. NO SUPPLY TO IC301 PIN 42 DUE TO R323 6K8 5W
1450T ONWA TUNING WON'T WORK CRACK IN PRINT OF REAR MAIN PCB
1455
1455 DEAD R913 220K
1455 DEAD NO STBY LIGHT R913 220K OHM
1455T DEAD HT OK,R323 6K8
1455TS COLOR CAST IC301 AN5601
1455TS LOSS OF ONE COLOR IC301 IC**AN5601
1455TS SND CRACKLES INTERMTTANTLY POSSIBLE ON/OFF SWITCH ARCING
1455TS STBY X601 4MHZ CRYSTAL
1455TS STUCK ON STBY WHEN COLD X601 4MHZ CRYSTAL
1455TS WHISTLES C143 10UF FRONT RHS NEAR MICROPRO
1455TS WHISTLES INT C143 10U FRONT RHS NEAR MICRO
145T DEAD EXCEPT SBY LIGHT AND CHANNEL IND R502/3 OC.330K
145T SBY R502 R503 330K
145TT
145TT DEAD - 300V BUT NO START UP VOLTS C 427 33UF 50V(START VOLTS BEING DROPPED ACROSS START RESISTORS)
145TT DEAD 320V OKS C427 33MFD 50V
145TT DEAD CHAN DISPLAYLIT R502/503 330K
145TT ORION 14A CHASSIS
145TT STBY NO 102VN , STR50103 CR502/3 (330K)
145TTA
145TTA DEAD 320V OK R502 330K
145TTA DEAD NO VOLTS PIN 2 STR50103 REG - R502 330K
145TTA DEAD STR50103 /R502(330K).
145TTA DEAD ZERO VOLTAGE AT PIN 2 OF THE STR50103 REGULAT R502(330K)
145TTA STBY R502/3 330K START UP RES
147 SEE BUSH 1400 ONWA
147 DEAD 300V OK R906(1K8)
147 DEAD ZD402 R425 C911 & C909 BEWARE ORIENTATION OF C909 SHOULD BE "-" PLATE TO Q904
147 DEAD ZD402(12V ZEN) R425 C911(47UF) & C909
147/149 DEAD SEE BUSH 1400
1475TS
1475TS CP375 DAEWOO
1475TS DAEWOO CP375 OR CP005
1475TS GOTO DAEWOO.TV.html
1475TS LOPTR 2SD2499/(BU508DFI+47RR)+LOPTX 1142.5057 HR7880
1476TS
1476TS CP005 2003 AROUND
1476TS DAEWOO CP375 OR CP005
1476TS GOTO DAEWOO.TV.html
1476TS STBY , I901 (TDA6103Q) ON CRT BASE PCB
1476TS STBY I901(TDA6103Q)
1476TS TOUCH VOLUME AND ALL CONTROLS LOCK, ?? EEPROM(24WC16P)
147TT
147TT BLANK RASTER A1'S FUSSY R430 180K
147TT DEAD ZD402 (12V 1W ) + R425 (5R63W) + C911 + DZ901 (8V2) + C909
147TT DEAD ZD402 12V, R425 5R6 3W C911(47UF50V FIT 100UF)
147TT DEAD, C911 47UF35V(MARKED REVERSE) 12 ZENER +12R
147TT DIST FIELD R413 6K8 HIGH
147TT NO SOUND LOW 12V RAIL 10R GONE HI.
147TT NO VIS , BLANK RASTER(MAY RE-APPEAR WHEN A1 ADJ. R430 180K
147TT POOR FIELD LIN R413 6K8
147TT POOR/NO STORE,33V OK,TUNING VOLTS OK, UE33-B21 ONWA KWTA C68212Y 05563 MAYW 236.
147TT SAME AS ALBA CTV841 ALSO BUSH 1452T
148
148 NO UP CHAN EEPROM CT24C02P
148 WONT STEP UP CHANNELS INT(ALSO OTHER ODD EFFECTS MEM ICS(BOTH) IC**CAT24C02P
148T SEE DAEWOO CP315
148T BLANK RASTER 5V REG BROKEN LEGS ON TT BOARD.
148T INT BLANK RASTER, REMOVE TEXT SUBPANEL THEN WORKS OK.
148T ROLLING AND PULLING PIC. C703 47NF
148T ROLLING/TEAR PIC. C703 47NF
148TT
149 SEE BUSH 1400 ONWA
1490T-IB FORMENTI FPC203 (PCB MARKED FPC230.1) REMOTE SF5, LOPTX 1142.1695, LOPTR BU TUNING - HOLD […] FOR >5 SEC, THIS IS THE SAME BUTTON THAT BRING MAIN MENU IF QUICKLY PRESSED.
1495T-IB FORMENTI FPC2002 2002
149TT
149TT BUZZ ON SOUND AFC ? TA8701AN
149TT DEAD 300V OK R906(1K8)
149TT DEAD ZD402 R425 C911 & C909 BEWARE ORIENTATION OF C909 SHOULD BE "-" PLATE TO Q904
149TT DEAD ZD402 R425 C911 C909 USUAL ONWA
149TT FIELD COLLAPSE R375 180K (CONNECTED TO PIN 33 AN5601 IC301)
149TT INT TUNING /AFC COIL NEAREST TO IF CHIP.
149TT R425(2*4R7)
14RC
14RC LO CONTRAST/COLOR R241(150K) NR SCAN PLUG
14RC 20RC LOW CONTRAST/ COLOR R241(150K) NEAR SCAN PLUG
14TT ZENER ZD402 12V R452 5R6, C911 4U7F, 50V+ 8V2ZENER DZ901, C909 47UF, 50V
1790T 2003,
1903/9 C134(17N4F1600V)+D15(BY228) CHOPPERTR (S2000N) EW(TDA4950).
2018R SEE DAEWOO CP330
2018R CLICKS DAEWOO CP330 LOPTR(2SD5072 D+R) CAUSE LOPTX PINS S2000AF++
2019
2019R 12V ZEN+47UF+AN5601K.
2019R 47UF50V 12V ZENNER +6R8.
2019R CONTRAST AN5601K
2019R HI CONTAST Q615 5V REG
2019R MILKY OR STREAKY PIC ZD301 5.1V ZENER
2019R ONWA
2019R ONWA HIGH CONTAST - WONT REDUCE 7.5V ON 5V SUPPLY TO MICRO - Q615
2019R POOR CONTRAST AN5601K
2019R POOR PIC ZD301 5V1 ZENER
2019R(ONWA) IC301 AN5601K COL DEC CHIP
2025RS
2025RS DAEWOO CP375
2025RS DEAD IC1802
2025RS DEAD NO STBY LIGHT POWER SUPPLY RUNNING IC1802
2025RS THREE COLOR RINGS COVER ENTIRE SCREEN IC301
2028T SEE DAEWOO CP330
2028T LOCKED UP WITH NO CHANNEL XT01 27MHZ CRYSTAL
2028T NO CHANNEL CHANGE XT01 27MHZ CRYSTAL
2029T ONWA
2029T BLANK PIC/NO SND ZD401 R419 47UF IN PSU
2029T BLANK RASTER NO SND C113 0U01F
2029T BLANK RASTER NO SND (EHT & TUBE HEATERS OK) ZD401 R419.
2029T BLANK RASTER WITH NO SND C113 0.01UF FOR
2029T BLANK RASTER WITH NO SND(EHT & TUBE HEATERS PRESENT) ZD401 R419 47UF63V IN PSU
2029T DEAD 300V OK R906(1K8)
2029T DEAD R901(4R7)+C905(4700PF500V ACROSS BRIDGE)+C911(47UF50V).
2029T DEAD R917(0R62) D905(BA157)
2029T DEAD, 100UF160V+2SD1555+R110(0R5)+C911(100UF50V).
2029T INT DEAD RELAY TERMINALS
2029T INT STBY MICRO PRO,NVR
2029T JUST SNOW, TUNER UNIT,IF FILTER XTAL
2029T ONWA
2032
2032 BURNUP C444(330PF2KV).
2032 DEAD - SMOKING C444 330PF 2KV
2032 DEAD BURNING SMELL C444 330PF2KV.
2032 DEAD SMELLS C444 330PF 2KV
2032 INT TOP CRAMP C812 NR CHOPPERTX.
2032 NIKKAI NT20
2032 NIKKAI NT20 TOP CRAMP C313(2U2F250V)
2032 NO STORE/STOP TUNER DRIFT Q805/Q803 PINS.
2032 SMOKING C444 330UF, 2KV HAD BECOME A PILE OF ASH.
2040R DEAD RELAY CLICKS R803(390K)
2040R DEAD STBY LED LIT RELAY CLICKS WHEN R/C PUSHED R803(390K) PIN 3 IC 801
2040R HR7455 ADD 6 TURN WINDING ON CORE TO PIN 4 (HT) & FEEDBACK CUT 1 LINK
2043
2043 DEAD NO HT 106VN FR803 4R7
2043 DEAD PSU WORKING BUT NO 106V O/P AT D803 - FR803 4R7 FUSIBLE DRY JOINTS
2043 GOLDSTAR PC04A
2043 GOLDSTAR PC04A DEAD C807S(33UF160V).
2043 GOLDSTAR PC04A NO HT(106V) FR803(4R7).
2043T GOLDSTAR PC04A SEE GOLDSTAR
2043T BLACK BLOBS ON TOP SIDES OF SCREEN C406 1U 160V IN LINE SCAN COUPLING
2043T BLACK BLOBS TOP SIDES C406 1UF160V LINE SCAN COUPLING
2043T COLD LO HT , 33UF160V CAP SITUATED CLOSE TO THE POWER SUPPLY TRANSFORMER.
2043T DARK WITH HIGH COL CONTENT & TUNER DRIFT 12V SUPPLY AT C429 8V. R437 & R427 HI RES - FIT 1R5 1W TYPES
2043T DARK+HI COLOUR+TUNER DRIFT R437+R427 1R5.
2043T DEAD - HT OK AT PIN 17 OF CHOPPER TFMR NO HT AT B+ OF LOPTX - D8035
2043T DEAD D8035
2043T DEAD D8035 FOR LOCATED OFF PIN B OF LOPTX
2043T DEAD C805P 100U 16V IN PSU
2043T DEAD C805P 100UF16V IN PSU
2043T DEAD C805P(100UF16V).
2043T DEAD HT LOW C8075
2043T DEAD HT OK D8035
2043T DEAD LO HT C8075
2043T DEAD POWER SUPPLY OK D8035 OC
2043T DEAD. C805P 100UF, 16V THAT IS MOUNTED IN FRONT OF THE POWER CHOPPER TRANSISTOR
2043T GOLDSTAR PC04A ODD BLANKING SPOTS C406(1UF160V).
2043T NO/POOR LUMA TUNER DRIFT C429 R437 R427 1R5
2043T PSU OK, NO HT DIODE D8035 WAS OPEN-CIRCUIT.
2045
2045TS DAEWOO CP375 SEE GOTO
2045TS DEAD PBC BURNT NR ON/OFF SWITCH
2045TS CP375
2045TS DEAD BURNUP LOPTX 11425057=HR7880 EXPENSIVE
2045TS DEAD FLASH LED,C409(40OPF2KV), LOPTR(2SD2499 INT 47R+D)
2050R TATUNG C SERIES TOPTEL 025/125.
2050R COLD LO WIDTH R413 18R
2050R LINE DOWN PIC WHEN COLD (FOLDED SCAN) R413 18R ½W HI RES - HT CORRECT -115V 14/20"; 109.5V 15/21"
2050R TATUNG C SERIES
2050T CHILD LOCK TO REMOVE HOLD P+ WHILE TURNING ON POWER
2052T ONWA
2052T ONWA STBY. C910(100UF , 160V) IN LTB.
2052T STBY. C910(100UF160V)
2053
2053 MAX VOLUME IS LIMITED IN TEST MODE TO EXIT HOLD VOLUME DOWN BUTTON WHILE TURNING ON POWER
2053T A HOTEL MODE MAX SND, HOLD VOLUME DWN AND TURN POWER ON
2053T DECCA A SERIES DEAD/STBY LO HT,SCANCOILS BURNT
2053T DECCA A SERIES DEGAUSS POSS IR RECIEVER TFMS4360N.
2053T IR SENSOR(TFMS4360N/TFK4 236)
2053T NO ON SCREEN DISPLAY TEXT BAR STILL PRESENT AT BOT 10 MHZ CRYSTAL ON IC 702
2053T NO OSD 10 MHZ XTAL ON IC702
2053T TATUNG (A SERIES ?)
2053T TATUNG A INT POOR PIC,XL551 ON SUB PCB
2055 LOPTX 2 TYPES DCF2217L=DAEW50H0000121 AND DCF2217J=DAEW50H0000124
2055 SEARCHES PAST STATIONS , NO STATION IDENT. TDA8362B
2055 SEARCHES WON'T STOP TDA8362B
2055T
2055T SEE GOTO
2055T COLD INT BLANK RASTER TDA8362+AN5862K.
2055T DAEWOO CP315 INT PIC REMOVE TEXT PANEL
2055T DAEWOO CP315 REMOVE TEXT PCB STILL WORKS OK
2055T DEAD STK37410/DII
2055T INT LOSS OF PIC NO TEXT 27MHZ CRYSTAL ON TEXT PCB
2055T INT NO PIC/TEXT 27MHZ XTAL ON TEXT PCB
2055T NO COLOR/UNLOCKED CHROMA OSC/NO TEXT SYNC TDA8362B.
205N
205N CP365
205N DAEWOO CP365 TOPTEL 125 8 SCREWS MODEL T20C1
205N GOTO DAEWOO CP365
205N INT DEAD CHOPTR,LINE DRV TX
205N INT DEAD DRY JOINT "HV" PIN ON LOPTX
205N NORMAL SET, STORE WITH STORE AND RETURN TO NORMAL BY PRESSING "MENU" TWICE.
205N POOR FIELD LIN & TUNING DRIFT 8V REG I402 FAULTY (RUNNING HOT)
205N STBY C811, 812, 813 & HT IS 103V AT RELAY
2065
2065 CP005 DEADISH C827(2200UF16V)
2065TS DAEWOO CP005
2066 CP005 DEAWOO
2066TS DAEWOO CP005 2003
206N
206NS CP380 SEE DAEWOO SEE GOTO
206NS BLANK RASTER, NO SND,EARTH SPEAKERS/GRILL TO CRT RIMBAND
206NS DAEWOO CP380 SERV. MODE - SPECIAL REMOTE R-30SVC
206NS DEAD. F801 BLOWN IC801 REGULATOR FAULTY
206NS LINE TEARING AFTER WARM UP POSSIBLE DRY JOINTS ON IC501
206NS NO GREEN ON TELETEXT PIC OK D702 1N4048
20R
20RC LO CONTRAST/COLOUR R241(150K) NR SCAN PLUG
20XRT NO CONTRAST ADJ V AT PIN 6 TDA3562 SHOULD VARI WITH CONTRAST IF NOT R414(33K)
20XRT NO CONTRAST TDA3562 R414(33K)
2143 DEAD C804P 8N2
2143 SHUTS DOWN OR DEAD C804P 8N2
2145TS DAEWOO CP375 SEE GOTO
2155PF DAEWOO CP485
215N
215N DAEWOO CP365 CHOPTX PINS
215N GOTO DAEWOO CP365
215N SEE 205N
215N AUDIO BUZZ FROM BOTH CHANNELS RESOLDER FIELD IC HEAT SINK
215N BLANK WHITE RASTER OSD OK,
215N DAEWOO CP365
215N GREY SCALE OK UNTIL COLOR INCREASED THEN SCREEN GOES PINK IC501 TDA8362
215N GREY SCALE PINK IC501 TDA8362
215N LOCK OUT ALL BUTTONS & HANDSET INOPERATIVE IC710(SN76861NJ12)
215N LOPTX 2 TYPES DCF2217L=DAEW50H0000121 AND DCF2217J=DAEW50H0000124
215N NO CHANNEL WITH REMOTE OR FRONT BUTTONS 13.89MHZ CRYSTAL
215N NO CONTROLS/HANDSET 13.89MHZ CRYSTAL
215N NO CONTROLS/HANDSET IC710(SN76861NJ12)
215N NORMAL SET, STORE WITH STORE AND RETURN TO NORMAL BY PRESSING "MENU" TWICE.
215N PP STORE THEN "MENU" TWICE.
215N SND BUZZ FRAME IC HEAT SINK EARTHS
215N/2055 WIDTH, AFTER LOPTX,DCF2217L=DAEW50H0000121,DCF2217J=DAEW50H0000124
216
2160PF 2003 2004
216NS DAEWOO CP380 goto daewoo
216NS DAEWOO CP365
216NS DAEWOO CP380
216NS SINGLE POLE ON/OFF SWITCH, PCB BURNUP.
2170
2170 / 2180 DEAD R105 150K, R106 150K, R107 270K & R108 270K
2170 2180
2170 DEAD R105 150K, R106 150K, R107 270K R108 270K
2170 DEAD R108 270K.
2170 DEAD. 320V OK, R108 70K WAS OPEN CIRCUIT
2170 EXCESS BRILL 100UH COIL ON CRT BASE,
2170 EXCESS BRILL NO 190V ON CRT PCB. 100UH CHOKE IN SERIES WITH SUPPLY
2170 VIDEO PB FLAG WAVING C287(1UF)
2170R 2180 WILL NOT GO INTO STBY R105 R106 180K
2170R NO STBY R105 R106 180K
2175
2175
2175 2185 WILL NOT GO INTO STBY R102 & R103(150K)
2175 DEAD/STBY R102 R103 BOTH 150K TWO 270K RESISTORS R104 AND R105.
2175 FLAG WAVING ON VCR, FIT(1UF) IN PLACE OF C287 & C233
2175 GOODMANS 2175,CTV2,CTV2180=FAT30200
2175 HT=103VN/17VN
2175 NO STBY R102 & R103(150K)
2175 POOR STBY 150K
2175 STBY R102, R103 150K - ALSO R104, R105 270K
2175 STBY R102, R103 150K R104, R105 270K
2175 VIDEO PB FLAG WAVING C233(1UF)
2175R FIELD FOLDOVER . C333 (4U7F160V)
2175R FIELD FOLDOVER OF ABOUT TWO INCHES. C333(4.7UF)
2175R FIELD TOP FOLDOVER C333 4U7 160V
2175R FRAME COLLAPSE R326(3R3) FROM LOPTX
2175R GREEN PIC R618 330K ON CRT BASE.
2175R GREEN SMEARY PIC R619 330K ON CRT BASE OC
2175R INT DEAD STR54041
2175R LIKE PROTECH CTV2001R.
2175R SMEARY PIC R619 330K ON CRT BASE
2175R TOP FOLD C333(4U7F160V).
2175RA COLOR CAST RED R620 220K CRT BASE
2175RA COLORS FLASH AS IT WARMS UP LEAVING RED R620 220K CATHODE CURR MEASUREMENT RES ON CRT BASE
2175RA RED PIC R620(220K) ON CRT BASE PANEL.
2175RA WARM PIC FLASH, R620 220K ON THE CRT BASE PANEL
2178
217NS
217NS DAEWOO (CP785) =257NS
2180 1" FIELD Q212(2SC2073 NPN)
2180 ALMOST FIELD COLLAPSE Q212 2SC2073
2180 DEAD R105 150K, R106 150K, R107 270K R108 270K
2180 DEAD R105 106 150K R107 108 270K NEAR OPTOCOUPLER
2180 DEAD R105 106 150K R107 108 270K NR OPTOCOUPLER
2180 DEAD R801 270K IN PSU
2180 DEAD STBY LIT OK STR54041 /R108 270K.
2180 DEAD. R105(150K) , R106(150K) , R107(270K) , R108(270K) BY CNX82 IN PSU
2180 FLAG WAVING ON VCR, FIT(1UF) IN PLACE OF C287 & C233
2180 INT LOW BRIGHTNESS,CRT BASE PCB BROWN GLUE LEAKING A1'S AWAY
2180 INT/COLD LO BRILL CRT BASE PANEL A1S.
2180 LOW BRILL ESP AT SW ON A1 VOLTS LOW - CONDUCTIVE GLUE ON CRT BASE
2180 LOW BRILL LO A1'S GLUE ON CRT BASE
2180 NIKKAI
2180 NIKKAI ON/OFF SWITCH PREH 38
2180 NO PIC - SND OK NO VOLTS COLL LINE DR TR DUE TO TFMR PRI
2180 NO PIC SND OK LINE DR TX
2180 NO PIC SND OK,HT OK LOPTX O/C
2180 NO S/V LINE HUM BLANK RASTER C216
2180 NO SND/PIC C216
2180 NO STBY R105 R106 180K
2180 PARTIAL FIELD COLLAPSE 2SC2073 NPN TRANSISTOR Q212 +D206,
2180 PARTIAL FIELD COLLAPSE Q212 2SC2073
2180 TOP FOLD OVER,D206.
2180 TOP FOLDOVER D206
2180 TOP FOLDOVER DRY JOINT D206 IN FOP CCT
2180 VIDEO PB FLAG WAVING C287(1UF)
2185
2185 DEAD 300V AT PIN 3 STK54041 R104(270K)
2185 DEAD 300V OK STK54041 R104(270K)
2185 DEAD LOPTR C264 47UF160V
2185 DEAD WITH LINE O/P TRANSISTOR C264 47UF160V
2185 LOW FIELD/WIDTH , HUM ETC. HT SMOOTHING 220 UF , 200V
2185 NO STBY R102 & R103(150K)
2185 SMALL PIC 220UF200V
2185 VIDEO PB FLAG WAVING C233(1UF)
2185T DEAD 320V OK, R104 270K
2185T DEAD R104 270K
2185T DEAD R104 270K R105 R106
2185T DEAD STBY LIGHT GOES OUT AT SW ON - R104 270K IN START UP CCT - R105 & 106 CAN ALSO BE RESPONSIBLE
2185T FIELD COLLAPSE TDA4505E ,R325(1R) NR LOPTX.
2185T FIELD CRAMP C333 4U7F
2185T FIELD CRAMP C333(4U7F).
2185T FIELD CRAMPING C333 4U7
2185T GREEN PIC R618 470K
2185T GREEN PIC R618 470K (COVERED IN GUNGE)
2185T GREEN R618(330K).
2185T INT START,STR54041 150K+120K
2185TA 120VN/17VN,WEAK/DIST SND IF COIL NEAREST TUNER.
2185TA FIELD COLLAPSE Q232/Q233(2SA940 2SC2073) R325(1R)
2185TA INT GOES OFF/ON STR54041
218NS DAEWOO CP385
2195 EXCESS WIDTH C411 0U47F
2195 EXCESS WIDTH (AFTER TRANSFORMER ) VALUE OF C411 FROM 0.33 TO 0.47
2195 NORMAL SET, STORE WITH STORE AND RETURN TO NORMAL BY PRESSING "MENU" TWICE.
2195 PP STORE THEN "MENU" TWICE.
2195T CP330 DAEWOO SEE GOTO
2195T CP330 DEAD FUSE 4AT, DEGAUSS POSISTOR
2195T DAEWOO CP330
2195T FRAME JITTER C304 0U47F
2195T LOCKED UP WITH NO CHANNEL XT01 27MHZ CRYSTAL
2195T NO CHANNEL CHANGE XT01 27MHZ CRYSTAL
219T
219T INT TUNING DT2-1V15P CHIP INSIDE TYPE.
2275 SEE F11
255NS
255NS CP775 SEE DAEWOO
255NS SEE DAEWOO CP775
255NS CP775 NO SND/PIC C416(680PF2KV),R409(4K7),R503(10K),RC527(10RSM)
255NS DAEWOO CP775
255NS DEAD WITH PSU RUNNING NO OR LOW LINE DRIVE AT BASE Q402 LINE DR - TRS Q405 2SA854 & Q406 2SC945 FOR LEAK
255NS NO PIC SND OK,RESOLDER ALL LOPTX AREA
255NS POOR AV2 PIC DA18
255NS WEAK CONTRAST AND POOR SYNC ON AV2 DA18
256NS
256NS E/W DIST C2913 (390N 250V) AND 7908 (STP4NA40F1) MOSFET
256NS BENT SIDES EW C2913(390NF250V) 7908(STP4NA40F1 MOSFET)
256NS DEAD & WHISTLING C2912 BLUE DISC CAP 2N2 2KV
256NS DEAD NOISE C2912 BLUE DISC CAP 2N2 2KV
256NS E-W DIST CAPACITOR 2913 (390N 250V) AND 7908 (STP4NA40F1 MOSFET)
256NS GOTO L6.2 PHILIPS
256NS L6.3AA SEE PHILIPS.TV
256NS NO E/W CORRECTION & LOW WIDTH 390 NF 250 V CAP(REF 2913) BIG BLUE CAP ON THE E/W BOARD
256NS PHILIPS L6.2
2575
2575 2875 3375
2575 2875 INT BRIGHTNESS VARYING A1 SUPPLY , POSS LOPT
2575 BLANK RASTER INTERMITTENTLY D44 BA157 WITH 1N4007
2575 DEAD - HT VERY LOW BY448 DIODE IN EW STAGE
2575 DEAD .RED LIGHT FADES DIODE D35 , PRIMARY CHOPTX BA157
2575 DEAD 2A FUSE ; CHOPPER TR S2000AF ; C102 100U, C103 100U, C107 100U; D33 1N4007 MAINS RECT ;
2575 DEAD HUMMING,LO 320V 150UF400V IN PSU
2575 DEAD SMELL 10R 5W LOPTR. C134 10N LINE FLYBACK
2575 DEAD WITH CHIRP C134 10N, 1K6 BURNT, LOPTR S2055AF
2575 DEAD WITH SMOKE DRY JOINT/ BURNT C134; D45 BY228
2575 DEAD WITH SMOKE LINK 13 DRY JOINTS
2575 E/W FAULTY TDA4950 - VOLTS READINGS DON'T AGREE WITH CCT DIAG EVEN WHEN OK
2575 F11
2575 F11 SEE BELOW FORMENTI
2575 FORMENTI F11
2575 INT REVERTS TO STBY ELECTS ON PSU PRI & DRY JOINTS - HT = 142V
2575 INT START UP R19 FROM 1K2 TO 4K7(LOCATION IC1 PIN 33 ACROSS D9)
2575 NO RED R26 68K ON CRT BASE
2575 ONE COLOR HI, R26 R28 R29 ON CRT BASE. 68K
2575 REVERTS TO STBY AFT FEW SECS C108 IN CHOPPER CCT
2575 ROPE EFFECT 3" FROM LHS LINE DRIVE TR
2575 WON'T SWITCH ON FROM COLD C102 IN POWER SUPPLY
2575TV DEAD DRY JOINTS LINK 13 ON MAIN PCB
2576
2576 BENT SIDES EW IC18 TDA4950
2576 E/W FAULTY IC18 TDA4950
257NS DAEWOO CP785
258 FERGUSON TX92
2580
2580 FERG TX92 SEE FERG_TX.TV.html.
2580 BRIDGE(2) CHOPFET STP6NA60F1 (WVE2066TR)+TDA4605-3 +CP13 1N5F1K6V .
2580 NO SND TS90(BC848B SM) MUTE STAGE
2580 SND MISSING TS90 BC848B SM IN SND MUTE STAGE
2580 TX92 LINE SPITTING LOPT EHT LEAD
2580 TX92 NO SND BC848B-SM TS90
2580(TX92) LINE TEARING AFTER SET WARMS UP EHT LEAD IS FULLY SLOTTED INTO LOPT
258NS DAEWOO CHASSIS 2003,
2595
2595N NO RED VISTA TUBE GONE
2595TN NO STBY R105 R106(150K)
2595TN WILL NOT GO INTO STBY R105 & R106(150K)
25C22F DEAD NO HT R811 270K
25C22F DEAD NO HT R811(370K)
268NS NO SND MPS3410
28"(66CM) HI COLOR+LOW BRILL 68K ON CRT BASE.
285
285 DEAD C416 680 PF ; D506 ; RC527 SM RES 10R; D504 & TDA8375A
285DPL NOT SAME AS 285NS
285DPL STBY VK51 BY228 AND VK61 BYW74 FOR
285DPL ARCING NOISE LOPTX(1192.6002/ HR7388)
285DPL ARCING ON PIC RESOLDER LINE O/P TRANSISTOR HEAT SINK
285DPL BLANK RASTER SND OK C416,R409,R503 D506
285DPL BLANK RASTER WITH SND C416,R409,R503 AND D506
285DPL DEAD EHT SURGE LOPTX
285DPL DEAD LED FLASHES RK68 VK71 NS10
285DPL DEAD WITH STBY LIGHT FLASHING RK68 AND VK71
285DPL EHT COMES UP THEN SET SHUTS DOWN SUSPECT LOPTX
285DPL FIELD COLLAPSE TDA8350Q AND RK68 10R
285DPL FINLAND NOKIA, S2000N(NO R NO D ISOL) LOPTR +EARTHS,
285DPL LACK OF WIDTH WITH E/W DISTORTION RK62 FOR DRY JOINTS
285DPL LED FLASHES 3 TIMES THEN STAYS ON SET DEAD VK71 AND NS10
285DPL LINE SPITTING LOPTR HEAT SINK
285DPL LO WIDTH EW RK62
285DPL NO SND FROM HEADPHONE SOCKET HEADPHONE LEVEL IN SND MENU
285DPL NOISE ON STBY REMOVE LINK WA21 ON DOLBY MODULE
285DPL NOKIA STBY FIELD CHIP(TDA8350Q),NS10(10R),RK68 BY399
285DPL POOR FOCUS RK61
285DPL POWERS UP THEN GOES TO STANDY VK67 ON PIN 3 OF LOPTX
285DPL PUTTING NOISE ON STBY REMOVE LINK WA21 ON DOLBY MODULE
285DPL R026 TOUCHING HEATSINK
285DPL STBY C093 CONNECTED BETWEEN PINS 2 AND 4 OF THE IC.
285DPL STBY VK51 BY228 VK61 BYW74
285DPL STEREO PLUS
285DPL SURGE STBY VK67 ON PIN 3 OF LOPTX
285DPL TICKING NOISE FROM FOCUS UNIT AND PIC OUT OF FOCUS ,N RK61
285NS
285NS SEE DAEWOO CP775 GB2898ST DEC1999
285NS GOTO (A HREF="/tvs/DAEWOO.TV.html">DAEWOO.TV.html
285NS SERVICE MODE TO SET UP HEIGHT REQS SPECIAL HANDSET
285NS (B) BLANK RASTER SND OK THEN PIC APPEARS AFTER 20 MINS JUNGLE IC
285NS ** WARNING ** WARM LOPTX FLASHOVER CAUSES/BLOWS ALL SORTS OF FAULTS
285NS = DAEWOO GB2898ST CP775
285NS BUZZ ON SND WHEN VOLUME AT LOW LEVEL HEATSINKS EARTHS
285NS BUZZ SND ,EARTH PEGS OF HEATSINKS OF AUDIO AND FIELD OUTPUT ICS
285NS CABINET RATTLE REMOVE SPEAKER GRILLS AND FIT FELT
285NS CAUSING TIMER PROBLEMS WITH SOME VCR'S MICRO
285NS CP775
285NS CP775 DAEWOO LOPTX HR7927/13525008
285NS CP775 DEAD LOPTR(2SD1880 INT D+56R/BU2508AF+D REMOVE 22R FIT 68R)
285NS DAEWOO CP775
285NS DEAD - TICKING 2SD1880 LOPTR U/S, LOPTX (HR7927) U/S, & RGP30J DIODE
285NS DEAD LOPTX ARCED ,LOPTR,STR5707
285NS DEAD LOPTX ARCING 1352.5008/HR7927
285NS FULL VOLUME I702 EEPROM FAULTY
285NS LINE FOLDOVER AND EXCESIVE WIDTH C416 BLUE 2KV TYPE
285NS PIC SLOW TO COME ON - SND OK TDA8375A JUNGLE CHIP
285NS SND BUZZ HEAT SINK EARTHS
285NS TRIPS ONCE THEN DEAD ON 12V SUPPLY TO TUNER - MCES WILL REPAIR
285NS VARIOUS FAULTS D708 5V6 ZENER D709 5V6 ZENER
285NS(B) DARK PIC WHEN USING SUBTITLES SELECT TEXT THEN PRESS MENU AND ADJUST BRIGHTNESS LEVEL
285NSB DAEWOO CP775
285NSB DEAD - MAINS FUSE BLOWN POSITOR FAULTY - RATTLED & PIC SHIFTED TO LEFT UNTIL D
286 FINLAND
286DPL GREEN RESISTOR (R026) TOUCHING CHOPPER H/SINK
286N5/05 DEAD SURGE TR75055 BC337
286N5/05 SERVICE MODE MENU THEN 2,3,5,7 ON REMOTE * (STAR) WIDTH
286N5/05 SERVICE MODE1, (NO TUNING MENU) - TURN TV IN TO STBY FROM REMOTE
286N5/05 SERVICE MODE1, MENU THEN PRESS 2,3,5,7,
286N5/05 SERVICE MODE2 TURN POWER OFF FROM MAINS ON/OFF SWITCH AND WAIT UNTIL LED GOES OFF.
286N5/05 SERVICE MODE2,TO GET TO GEOMETRY SETTINGS PRESS *(STAR).
286N5/05 SERVICE MODE3 HOLD STBY BUTTON ON REMOTE CONTROL AND POWER UP FROM ON/OF SWITCH
286N5/05 SERVICE MODE3,IF THE EEPROM IS RELACED WITH BLANK ONE,
286N5/05 SERVICE MODE4 HOLD STBYE BUTTON FOR ABOUT 10 SECONDS THEN DE/ACTIVE HOTEL LOCK.
286N5/05 TRIES TO START UP THEN TRIPS TR75055 BC337
286NS
286NS GOTO (A HREF="/tvs/PHILIPS.TV.html">PHILIPS.TV.html
286NS PHILIPS L6.2
286NS PHILIPS L6.3AA
286NS (PHILIPS L6.3) NO SND - NOISE MPS3410 CHIP , AUDIO PCB
286NS BENT SIDES EW,C2913(390NF250V) ON SUB PCB
286NS DEAD LOPTR,C2912(2N2F2KV)
286NS DEAD NO LED C2915
286NS DEAD NO POWER LED C2915
286NS FIELD COLLAPSE R3908 2R2
286NS FRAME COLLAPSE R3908 2R2
286NS L5901 EW COIL BURNT TURNS
286NS L6.2 DEAD FUSE F1502(100MA).
286NS L6.2 DEAD TR7505(BC337-40).
286NS L6.2 LO WIDTH EW R3924(10K PRESET POT) ON SUB PCB
286NS L6.2 STBY FS1502 WICKMAN FUSE
286NS L6.3 EW C2913(390NF250V)
286NS L6.3 LO WIDTH C2915(390NF250V)C2913(390NF250V)
286NS L6.3 LOPTR(BU1508AX) C2915(390NF250V)C2913(390NF250V)
286NS L6.3 SCANCOIL BURNUP(1R9 USUALLY)
286NS L6.3AA C2012(2200PF2KV) DISK CERAMIC BLUE, NR LOPTR
286NS PART FRAME COLLAPSE R3988 2R2
286NS PARTIAL FIELD COLLAPSE R3988 2.2OHM FUSABLE
286NS Philips L6.3 GOTO PHILIPS
286NS STBY 1502 BR CHOPTX ICFN25
286NS STUCK ON STBY FUSABLE 1502 BESIDE SMPS TRANSFORMER POSSIBLE ICFN25
286NS TORX T10 SCREWS L6.2/3
286NS/05 PHILIPS L6.2AA CHASSIS
286NS/05 DEAD LOPTR FIELD SCAN COILS SHORTED TURNS
286NS/05 DEAD WITH FAINT WHISTLE - LED LIT F1502 63MA IN PSU SEC
286NS/05 DEAD WITH FAINT WHISTLE - NO LED TR7505 BC337-40
286NS/05 F O/P TR OVERHEATS FIELD SCAN COILS SHORTED TURNS
286NS/05 GOES IN & OUT OF STBY AT SW ON TRANSISTOR 7505 BC337-40 (5V REG TR)
286NS/05 INT NARROW RASTER WITH SQUEAL BC338-40 IN 5/9V SUPPLY
286NS/05 INT STBY 7505 BC337-40 (5V REG )
286NS/05 Philips L6.2 GOTO PHILIPS
286NS/05 PHILIPS L6.2AA CHASSIS
286NS/05 PHILIPS L6.2AA NO 5V FROM PSU FR1502(MP63) NEED REMOTE.
286NS/05 TUNER UNIT U943C
286TVS/05 PHILIPS L6.2 SEE PHILIPS.TV.html
2875
2875 (F11) DEAD WITH TR15 S2000N S2000N AND C102 100UFD WHICH WAS DOWN TO 20UFD
2875 AT SW ON SPKRS POP THEN SHUTS DOWN D35 (BA157) IN PSU. IT READ OK IN AND OUT OF CIRCUIT
2875 BLANK RASTER INTERMITTENTLY D44 BA157 WITH 1N4007
2875 COLD LINE TEARING , C123 IN POWER SUPPLY
2875 DEAD - PRI HT PTC2 SMALL BLUE START UP THERM
2875 DEAD (POSSIBLY - NO FAULT SUBMITTED WITH CURE) C143 0U01 1600V
2875 DEAD C102 100U 25V IN PSU HI ESR
2875 DEAD C134 E-W CAP DRY JOINTS & S2055AF LOP TR
2875 DEAD EW DIODES D45/47 & PINCUSH CHIP IC18 - DRY JOINTS C134
2875 DEAD EW MOD DIODE BY448 & FOR DRY JOINTS
2875 DEAD HUMMING,LO 320V 150UF400V IN PSU
2875 DEAD WITH BURNING SMELL 0U01 1.6K CAP IN LINE STAGE BURNT; BY228
2875 DEAD WITH BURNING SMELL 0U1 1.6KV CAP BURNT, BY228 ADJ TO CAP
2875 E-W FAULT (AFT BURN UP) TDA4950 E-W CHIP
2875 E.W. FAULT 10NF , HA POT , DIODE
2875 F11 SEE F11 FORMENTI CHASSIS
2875 F11 DEAD STBY R170 SAFETY RESISTOR FROM SECONDARY OFF CHOPPER TRANSFORMER DUE TO IC8 TDA1521 AUDIO OUTPUT .
2875 F11 FLAT LOOKING PIC WITH ONE OR MORE COLS MISSING FEEDBACK RES R26, R28, R29 68K ON CRT BASE
2875 F11 SEE FORMENTI.TV
2875 FORMENTI F11
2875 INT DEAD DRY JOINTS CHOPPER TFMR
2875 INT DEAD DRY JOINTS CHOPPER TFMR PINS
2875 INT START UP R19 FROM 1K2 TO 4K7(LOCATION IC1 PIN 33 ACROSS D9)
2875 NO BLUE R29 68K ON CRT BASE
2875 NO E-W OR WIDTH CONTROL TDA4950
2875 NO SND IC8 TDA1521
2875 ONE COLOR HI, R26 R28 R29 ON CRT BASE. 68K
2875 ROPE EFFECT 3" FROM LHS LINE DRIVE TR
2875 SMEARY, DEFOCUSED OR 1 PRI COL MISSING 3 X 68K RES ON CRT BASE
2875 TOPTEL CODE 124.
2876
2876 F11
2876 F11 LOW EMISSION CRT SYMPTOM, R26, 28 & 29 68K ON CRT BASE
2880
2880 FERGUSON TX92
2880 GOTO (A HREF="/tvs/FERG_TX.TV.html">FERG_TX.TV.html
2880 (ICC9) STBY TP66
2880 (ICC9) 2 INCH BAR OF SNOW AROUND BLANK SCREEN TR42
2880 (ICC9) INT FIELD CRAMPING DF31
2880 (ICC9) NO BLUE TV81
2880 (ICC9) WAVY PIC WITH BENT VERTICALS IP03
2880 (TX92) DARK PIC WITH FLYBACK LINES R816 2.2K ON CRT BASE
2880 (TX92) DEAD TP16, DP06 AND DP08 FOR
2880 (TX92) DOES NOT SWITCH TO TEXT AND OTHER REMOTE PROBLEMS 27 MHZ CRYSTAL QT01
2880 (TX92) INT NO SND IP80 FOR DRY JOINTS
2880 (TX92) NO POWER DL11 FOR AND RL11 FOR
2880 (TX92) NO SND TS90 AND TS81
2880 (TX92) NO SND TS90 AND TS81 TRANBC848B
2880 (TX92) NO STBY CRT HEATERS TR02 BC848B
2880 (TX92) NO TELETEXT TX16 TRANBC848
2880 (TX92) NO TEXT PAGE 100 TX31 BC848B
2880 COLOR CAST RP40 CP40
2880 FIELD COLLAPSE NOT IN CENTRE TP91 BC848B AND TP96 BC858B IN POWER SUPPLY
2880 FRAME COLLAPSE TP91 BC848B TP96 BC858B IN PSU
2880 ICC9 2 INCH BAR OF SNOW AROUND BLANK SCRN TR42
2880 ICC9 BENT VERTICALS IP03
2880 ICC9 INT FRAME CRAMPING DF31
2880 ICC9 NO BLUE TV81
2880 ICC9 STBY TP66
2880 PURITY PROBLEMS VALUES OF RP40 AND CP40
2880 TX92 DARK PIC FLYBACK LINES R816 2K2 ON CRT BASE
2880 TX92 DEAD DL11 RL11
2880 TX92 DEAD TL19,TP16,IP01,DP02-O5,FUSE
2880 TX92 DEAD TP16,DP06,DP08
2880 TX92 INT NO SND IP80
2880 TX92 NO SND BC848B-SM TS90
2880 TX92 NO SND TS90 TS81 BC848B
2880 TX92 NO STBY TR02 BC848B
2880 TX92 NO TELETEXT TX16 BC848
2880 TX92 NO TEXT 27 MHZ CRYSTAL QT01
2880 TX92 NO TEXT PAGE 100 TX31 BC848B
2880 TX92 NO TEXT SYNC TX31 BC848B
2880(TX92) DEAD FUSE BLOWN VIOLENTLY TL19,TP16,IP01,DP02-O5,AND FUSE
2880/TX92 NO SYNC ON TEXT AFTER 2 MINS TX31 BC848B
2898 DAEWOO CP775
289NS DAEWOO (CP785) MULTISTANDARD PAL/SECAM, I, B/G
289NS DAEWOO CP785 Goto daewoo
295NS 2003,
295NS DAEWOO CP785
2LD3202 VESTEL ??
336NS-A F19
336NS F16
336NS F16
336NS F16 HAVE CCT DIAG
336NS F16 Goto F16
3375
3375 BLANK RASTER INTERMITTENTLY D44 BA157 WITH 1N4007
3375 DEAD DRY JOINTS CHOPPER TRFMR
3375 F11 DEAD - TR15 S2000AF IN PSU, TR20 S2055AF , C134
3375 F11 DEAD WITH FAINT TICKING FROM PSU R164 100R 5W IN PSU
3375 F11 PHILIPS REMOTE WORKS A BIT GOTO F11
3375 F16
3375 FORMENTI F11
3375 GOES TO STBY UNLESS ON/OFF HELD (WHEN SWITCH HELD TDA8361
3375 INT START UP R19 FROM 1K2 TO 4K7(LOCATION IC1 PIN 33 ACROSS D9)
3375 ROPE EFFECT 3" FROM LHS LINE DRIVE TR
366NS-A F19
5" TV/RADIO BUZZ SND ADJUST QUADRATURE COIL L301
5" TV/RADIO EXCESS BRILL/NO SND, IC202
5" TV/RADIO FIELD COLLAPSE R519(10K)
5" TV/RADIO NO SND IC301,R307(22R),C317(470UF)
5" TV/RADIO NO TUNING,R206(10K)
5" TV/RADIO POOR CONTRAST CRT FAUK=LT
5" TV/RADIO POOR FOCUS CRT
5" TV/RADIO RADIO DEAD C104(100UF)
5" TV/RADIO DEAD DC POWER SOCKET
5" TV/RADIO DEAD Q702,Q703,D702
5" TV/RADIO EXCESS WIDTH,Q701(TIP42C)
5" TV/RADIO SNOWY PIC Q201 OR TUNER UNIT
5150RC
5150RC DEAD C666 150UF160V
5150RC DEAD TICKS L652 33UH COIL
5150RC DEAD WHISTLE/TICKS 33UH COIL L652 IN THE HT FEED,
5150RC DEAD WITH FAINT WHINE/TICK L652 33U COIL HT FEED IN LOP STAGE DRY JOINTS
5150RC FAINT WHINE+TICK L652 33UH+LOPTX PINS.
5160 BRIGHT WHITE SCREEN 100UF CAP(MAY BE C659 - RHS CENTRE TWEEN PSU AND LOPT. NEAR REGULATORS)
5160 BRIGHT WHITE SCRN C659S 100UF
5160 EXCESS BRIGHTNESS C629 100U 25V
5160 EXCESS BRILL C629 100UF25V
5160 WHITE RASTER C629(100UF25V)
5160TT BLANK RASTER C629(100UF25V).
5160TT HINARI CT15/ST200/VTV200/CDTV2 HINARI CT14
5160TT HINARICT15/ST200/VTV200/CDTV2 HINARI CT14
C100 LOW GAIN - SLIGHT HUM BAR - PIC ALSO PULLS HT POT FOR DRYS OR DIODES
C1401R
C1401R C43M INT COLOR, RESOLDER ALL AROUND DECODER CHIP.
C1401R DEAD 100V OK D806(1N4937).
C1401R DEAD NO 100V STR5412.
C1401R FLAT PIC, CRT LO EMISSION
C1401R IBT PIC IC502 12V REG
C1401R INT NO PIC 12V REGULATOR IC502
C1401R INT NO PIC REMOVE THE SCREENING CANS FROM THE IF MODULE AND LOOK FOR DRY-JOINTS,
C1401R INT PIC DRY JOINTS IF MODULE - MIN CERAMIC CAPS
C1401R INT PIC IF MODULE MIN CERAMIC CAPS
C1401R PIC INT OFF DRY JOINTS IC502 12V REG
C1401R SNOWY PIC DRY JOINTS TUNER EARTHS
C1401R SNOWY PIC TUNER EARTHS
C1401R STBY R802 390K
C1401R STR5412, STBY TX=13VAC,10VDC DCF1577?=LOPTX.
C1402
C1402 DEAD BRIDGE RECT
C1402 DEAD BRIDGE+OPTO STBY SWITCH.
C1402 DEAD D611-614 MAINS RECTS D - BY133 DOES
C1402 STBY BRIDGE RECT IC612 OPTO
C1402 STBY STR58041
C1403 TUNER UNIT U943/3139 147 11211
C141 BLOWS MAINS FUSE VIOLENTLY AT SW ON STR5412 WAS TO HEATSINK DUE TO DAMAGE OF MICA WASHER
C141 DEAD STR5412
C141 NIKKAI
C141 NO LINE DRV TDA4505E
C141 SNOW EM112 STBY MAINSTX
C141 SNOWY SCREEN, NO CHAN LIGHT OR SIGS/SND EM112 STBY MAINS TFMR - USE MENT THAT WILL GIVE 5V DC O/P
C14VP DEAD LED FLASH C811(100UF16V)
C2043T .
C2043T COLD LO HT 33UF160V NR CHOPTX
C2043T LOW HT WHEN COLD 33U 160V CAP BY CHOPPER TFMR
C210
C210 10" REMOTE CONTROL TV 2003,
C210 STBY RP07 330R SM - ALSO / RP10
C210 STBY RP07,RP10(330R).
C530 5" 12V COLOR PORTABLE
C530 DEAD LOPTX (43-74-5503)
C530 FIELD COLLAPSE RESOLDER LOPTX PINS
C600
C600 12V COLOUR PORTABLE COMET GROUP 01656/768841
C600 LINE NON LINE - BLACK AT RH SIDE OF SCREEN CAUSED BY GLUE BETWEEN R545 & ADJ COIL - SCRAPE OFF GLUE & RE-ROUTE CONNS & RESOLDER CONNS IN VICINITY
C600 LINE RHS GLUE WEEN R545 & ADJ COIL
CD2880 ICC9 DEAD FUSE 1A6T+ SMALL BROWN CAP ACROSS BRIDGE LEG.
CD2880 ICC9 IP03 OVERHEATING TL64(BC848BSM).
CI401R SNOWY PIC,TUNER UNIT
COMPACT 10 TOPTEL 080
COMPACT 10 HUM BAR BRIDGE RECT 4*1N5401
COMPACT 10 = HINARI CT16
COMPACT 10 DEAD FIELD CHIP AN5512
COMPACT 100
COMPACT 100 DEAD POWER OK, NO LINE DRIVE IC361(M51390ASP/225002)
COMPACT 100 FUSE 3.15AT+D651(BATTERY REVERSE PROTECTION)
COMPACT 100 HUM BAR WHEN HEATED 1N5402 RECT DIODE
COMPACT 100 HUMBAR INT BRIDGE RECT(KBU602G).
COMPACT 100 ROLLING/HUMBAR INT BRIDGE RECT(1N5401*4).
COMPACT 100 WARM HUM BAR 1N5402
COMPACT 110
COMPACT 110 EVERYTIME THEY COME IN CHANGE BOTH 47UF AND BOTH 180K IN PSU
COMPACT 110 SAMSUNG NAIKO N1088,ROADSTAR CTV552,GENEXXA GTV10
COMPACT 110 10" DEAD ,RP03(2R2)RP06(39R7W)CP10(2N21000V),CAUSE GLUE
COMPACT 110 DEAD REG , AND FIELD CHIP AN5512 PT NO. CPC*HN5652AN5512
COMPACT 110 DEAD 12V QPD1 2SB826 REG ,TDA3653B 4
COMPACT 110 DEAD 15V OK STBY LED DIM = ON/OFF SWITCH.
COMPACT 110 DEAD 15V OK TO REG 2SA1012/TIP42 PNP.
COMPACT 110 DEAD 39R5W PINS+2*180K+2*47UF IN PSU .
COMPACT 110 DEAD 47UF IN PSU+ 2 * 180K
COMPACT 110 DEAD AFTER RAN ON 24V INSTEAD OF 12V QPD1 2SB826 REG ,
COMPACT 110 DEAD BLACK GLUE, 180K+47UF IN PSU
COMPACT 110 DEAD CHOPTR(2SD1545)+RP03(2R2)+QP02(2SC945 NPN/2SD965)
COMPACT 110 DEAD CP12(6800UF16V) RP24 1.8K + 3 TRANSISTORS
COMPACT 110 DEAD FIELD ELECTROYTIC CAPS
COMPACT 110 DEAD HIGH HT - SIGNS ARE BULGING ELECTS IN FOP STAGE
COMPACT 110 DEAD INT START RP04/05 180K IN PSU 14VN
COMPACT 110 DEAD LOPTR QHO2(BU407)
COMPACT 110 DEAD NO PSU OPERATION R5 180K
COMPACT 110 DEAD PSU ONWA KIT
COMPACT 110 DEAD PSU BLOWS UP ONWA KIT AVAILABLE
COMPACT 110 DEAD R5(180K).
COMPACT 110 DEAD REMOVE BLACK GLUE, 180K START UP RESISTORS & 47U CAPS IN PSU
COMPACT 110 FIELD - LO HEIGHT BOTTOM CRAMP RP05 8K2 3W METAL FILM
COMPACT 110 FIELD COLLAPSE - TDA3653B FOP CHIP & FEED RES BURNT - USED 4R7 1/4W &
COMPACT 110 FIELD COLLAPSE CH01(4U7F).
COMPACT 110 FIELD COLLAPSE CV07(220UF),RV01(4R7),TDA3653B.
COMPACT 110 FIELD COLLAPSE HI 24V TO TDA3653B TDA8361(100UF100V).
COMPACT 110 FIELD COLLAPSE TDA3653B+220UF+VOLTS REG TIP42C(2SA1012).
COMPACT 110 HI HT CP22 CP30,RP04 RP05(180K) QP01(2SA1012/BD244C) ZP06(6V8)
COMPACT 110 INT DEAD FUSE HOLDER(5A) LOOKS OK .
COMPACT 110 LINE COLLAPSE CH01 4U7 50V BIPOLAR
COMPACT 110 LINE COLLAPSE CH01(4U7F50V BIPOLAR).
COMPACT 110 LINE COLLAPSE COIL FROM LOPTR COLLECTOR TO SCAN COILS.
COMPACT 110 LO HEIGHT RP05(8K2).
COMPACT 110 NO LINE DRIVE 52PIN CHIP UNDER METAL SCREENING
COMPACT 110 NO TUNER STOP M34300-012SP ?.
COMPACT 110 ONWA FEB98_P236 ONWA KIT+6800UF16V+RP24(1K8)+QP02.
COMPACT 110 OVERVOLTS MAKES CAPS SWELL UP, RP01 ZP01+ 247UF IN PSU
COMPACT 110 STBY ,LH01
COMPACT 110 STBY LEAVES DARK PIC , VOLS REG TRANSISTOR (2SA????) TIP42C.
COMPACT 110 STBY LED DIM/BRIGHT LOPTR HOT,BOOST DIODE(LT PR6005) CAUSE LOPTX
COMPACT 110 STBY RP01(470R ?),ZP01(5V ZENNER)
COMPACT 110 SWITCH FORWARD=NORMAL,BACK TO FORCE POWER ON,UNDER H/SINK.
COMPACT 110 VOLTS REG S/C PNP 2SA1012(TIP42)+RP04 39R+TDA3653B+.
COMPACT 110 ZP06(6V8) RV01(4R7) TDA3653
COMPACT 210
COMPACT 210 5AT(3.15AT)+BATTERY POLARITY PROTECTION DIODES.
COMPACT 210 DEAD BU407/BUT11A(BEHIND CHOPTX),CH08(820NF400V)
COMPACT 210 DEAD PSU BLOWN CAUSE RS06(39R) BROWN GLUE
COMPACT 210 DEAD R??(180K)*2 DOWN BESIDE 400V MAINS CAP
COMPACT 210 STBY LOPTR(BU407/BUT11A),CH08(0.082UF400V) LOC413
COMPACT 210 STBY RESOLDER REGULATOR. LOC414
COMPACT 510
COMPACT 510 DEAD ON/OFF SWITCH SHORTED OUT AFTER DIODE.
COMPACT 510 HUMBAR NO COLOR ,VOLTAGE REGULATOR,SEND TO COMET 768841.
COMPACT 510 NO COLOR SEND TO COMET 768841.
CP365 DEAD ON/OFF SWITCH TYPE SW00967 CPC.
CTV2 (T) BLANK RASTER SND OK.IC204(TDA3562A)
CTV2 (T) DEAD HT OK. LINE DRVTX ( PT NO.ABATETH19Y19BY )
CTV2 (T) NO SND/PIC Q103(CL155D),R181(5R6)
CTV2(T) BLANK RASTER - SND OK. IC204(TDA3562A)
CTV2(T) DEAD - HT OK. LINE DRIVE TX(PT NO.ABATETH19Y19BY)
CTV2(T) NO SND OR RASTER - DISPLAY OK. Q103(CL155D) , R181(5.6R 5W) .
CTV20XRT OSAKI 20 FIDELITY ZX3000
CTV20XRT CONTRAST WEAK TDA3562A PIN 6 VOLTS LOW AT 1.3V & DOESN'T VARY - R414 33K
CTV20XRT DEAD 2.2 R313
CTV20XRT DEAD 2R2 SURGE LIMITER R313
CTV20XRT DEAD R313 2R2 SURGE LIM
CTV20XRT OSAKI 20 FIDELITY ZX3000
CTV20XRT POOR CONTRAST TDA3562A R414 33K
CTV20XRT POOR CONTRAST.OSD OK,R414 33K
CTV2R DEAD. 5.6 5W R81 STR5412 IC102 R2M D141
CTV2R FIELD FOLDOVER C216 47U 63V
CTV2R FIELD FOLDOVER C216 47UF63V
CTV2R INT DEAD IC102 STR5412
CTV2R INT TRIPS IC102 STR5412
CTV2R NIKKAI TLG2121
CTV2R NO TUNING 5V FROM EM104 STBYTX
CTV2R NO TUNING OR SIGS OR 5V SUPPLY EM104 WINDING
CTV2T NIKKAI TLG2121
CTV2T R471(1R) FIELD POWER.
CTV2T RINGING ON VERTS C483 & R448 1K2 FOR
CTV2T RINGING VERTS C483 R448 1K2
CTV2T SERVERE RINGING AT TOP OF SCREEN DECREASES AS SCAN DAMPING COMPONENTS C483 & R448
CTV2T SEVERE RINGING, C483 AND R448 1.2K WAS OPEN CIRCUIT.
CTV2T TOP RINGING C483 R448
CTV322S V1.2 (PCA84C)
CTV66W1 11AK19 SERVICE MODE ,INSTALL MENU PRESS 4,7,2,5. WIDTH=28
CTX14X FIDELITY ZX4000 JACKSON MK2
F11
F11 SEE 3375
F11 SEE FORMENTI F11
F16
F16 SEE FORMENTI F11
F19
F19
F19 SEE FORMENTI F19
F28WTF FPC2001 (TWIST) FLAT SCREEN 2003
F32WTF BURNT LINE STAGE, D23 R168 C175,C176(1UF)FROM PIN 2 OF LOPTX/L19.
F32WTF FORMENTI
FPC2001 DEAD TTR19(S2055N),R168(6K8),C172(15NF)
FST51
FST51T/T INT SIGS / PATTERNING DY JOINTS TUNER; ADL L700 FOR PATT
FST51T/T INT TUNER; ADJ L700
FST51TT / MURPHY CTV3540 WHITE WITH FB LINES TDA8153+R115(220R)+100MAFUSE).
FST51TT MURPHY 3510T MURPHY CTV3540T
FST51TT WHITE RASTER FLYBCK 100MA FUSE& 220R R115 IC100
FST51TT WHITE RASTER WITH FB LINES 100MA FUSE & 220R R115 190V SUPPLY TO RGB CHIP IC100 - CHIP AND SUPPLY COMPS
FST51TT/MURPHY CTV3540T WHITE PIC/FLYBACK CRT PCB 100MA FUSE AND 220R (R115)TDA8153 RGB OUTPUT COMPACT 100 INT HUM BAR 1N5402-BRIDGE RECTIFIER DIODES
GB2898ST DAEWOO DEAD D505 C416,R409,RC527, R503 LOPTR 2SD1880 OK
GD25
GD2500 = FERGUSON TX92
GD2580 FERG TX92 DEAD CP13(1N5F1K6V) ACROSS CHOPPER
GD2580 FERG TX92 LHS BRIGHT LINE DOWN DECOUPLE TUNER 12V.
GD2580 FERG TX92 TUNER(MTM-4045 œ50) DRIFT/JUMPS OFF STATION, SCART IN OK.
GD2580 FERGUSON TX92
GD2580 FERGUSON TX92 DARK ONE SIDE,A NEW TUNER CLEARED THE FAULT
GD2580 LOUD WHISTLE LL26 COIL
GD2580 LOUD WHISTLE LL26 COIL IN LINE STAGE - HOT MELT GLUE USED
GD2580D TX92F
GD2592 TX92 DEAD TP16(FET),CP13,TDA4605,DP51(BY399).
GD2880 SEE FERG_TX.TV.html TX92
GD2880 DEAD RL12
GD2880 FERG ICC9 DP53(BY297) LEAKY, BLOWS POWER SUPPLY.
GD2880 GHOSTING LIKE AERIAL,IF JOINTS.
GD2880 NO PIC SND OK, HTR PINS CRT BASE
GD2880 POOR PIC WITH GHOSTING DRY JOINTS IF
GD2880 TX92 DEAD CP13(1N5F) NR CHOPTR.
GD2880 TX92 EHT SURGE STBY/TRIPPED S/C TL60(BC548B)B/E TO OVERIDE.
GD2880 TX92 STBY DF30(BAV103).
GD2880A = ICC9 THOMSON.
GD2880A FERGUSON ICC9
GD2880A ICC9
GD2880A ICC9 NO REMOTE, IR PICKUP.
GD2880A ICC9 BLANK RASTER TX16(BC858B)
GD2880A ICC9 BRIGHT BLUE , CRT(A66ECY13X01 VIDEOCOLOR)
GD2880A ICC9 DEAD INT TR85(BC848B) TR87(BC858B).
GD2880A ICC9 WARM BAD LINE WATERFALL EFFECT TL64 BC858B TRANSISTOR
GD2880A ICC9 WARM LINE WAVERING TL64(BC848BSM).
GD2880B
GD2880B = FERGUSON TX92
GD2880B FERG TX92 TUNING STORE.
GD2880B FERGUSON/THOMSON TXX92 TORX15 SCREWS
GD2880B GHOSTING/RINGING PIC WHICH COULDN'T BE FINE-TUNED TUNER FAULTY
GD2880B RINGING PIC TUNER
GD2880B TX92 DEAD SURGE,DL21(BY228) CL21,RL47(4R7)
GD2880B TX92F
GD2880D TX92F
GDVD141 LO SND,C14
GOODMANS TVC14VP(CP310)
GTV147 11AK08
GTV147 11AK08, 11AK20M-6(AFTER 1999) AK20 PROD.CODE: 10000675
GTV148 11AK08
GTV148T 11AK08, 11AK20M-6(AFTER 1999) AK20 PROD.CODE: 10000676
GTV14DVD COMBI LO HEIGHT,Q603(BC848)
GTV14DVD P1420 LOPTX CF0801, LOPTR 2SD2599, CHOPTR 2SD2500, MICRO
GTV14DVDXI TV +DVD 2003,
GTV20CTV DEAD C125 100UF25V IN 12V LINE
GTV211 PT9601 (BUSH 2027T)
GTV211 RAGGED VERTICALS,C25(47UF160V)
GTV211 SHORT PIC, NO VID & GREEN BACKGROUND SHORTING LINKS 1068/1169 (REAR OF PROC) ARE NOT TOUCHING TOGETHER
GTV211TV DEAD PULSING,LO 320V,C5(100UF400V)
GTV257 11AK19-5
GTV26W3LCD HAVE EEPROM DUMP (PONYPROG)
GTV26W3LCD 127W MADE=TURKEY VESTEL ? THESE LAST 18MONTHS(AVE)
GTV26W3LCD LINES DWN/ACROSS SND OK,25857797 26",20225273 QDI
GTV28
GTV28 DEAD C829(47UF250V)
GTV288 11AK19 GOTOVESTEL.TV
GTV288 VESTEL 11AK19
GTV288 11AK12-9 DEAD R826(100K)+TDA4603+BUZ80A+R805(330K).
GTV288 11AK12-9 DEAD CHOPTX PIN
GTV288 11AK12 C829(47UF250V)
GTV288 DEAD CHOPPER TFMR DRY JOINTS CAUSED BURN UP - RESOLDERED (11AK12-9 )
GTV288 DEAD,GREEN LED FLASH R867(0R33)
GTV288SIL 11AK19 R629(27R)
GTV288SIL 11AK19E3, 11AK19P4, 11AK19P5 2000-2002 AK19 PROD.CODE: 10006762
GTV34R2 11AK20M-6 1999- AK20 PROD.CODE: 10000677
GTV34R3
GTV34R3 BLANK RASTER, 5V REG PINS UNDERNEATH
GTV34R3 INT DEAD 5VREG (L7805CV) LOC12
GTV34R3 INT DEAD CHOPTX PINS.
GTV34R3 ONWA DEAD RP4(330K).
GTV34R3 STBY ,HT OK,NO LINE DRV, XTAL(BLUE) NR STV2102B(JUNGLE CHIP)
GTV34R3DVD TOO LOUD ???
GTV34R6SIL 11AK20SE1
GTV34RDVD CHASSIS P1420 (TV+DVD) 2002 PCB MARKED 0707-A20261-03
GTV34RDVDXI 11AK46 GOTOVESTEL.TV
GTV34RDVDXI 11AK46 (TV+DVD)
GTV34T2 11AK20M-6 1999- AK20 PROD.CODE: 10000678
GTV34T6SIL 11AK36
GTV34T6SIL SEE VESTEL 11AK36
GTV370VCRX SERV.MODE SEE BUSH BTV16, BTV20
GTV371
GTV371 TATUNG TVC563
GTV371VCR BUSH BTV17, TATUNG TVC563, DECK OVD-6 PCB MARKED TM9423A, VIDEO VM9162A MICRO OEC0078A, OPTION CODES EEPROM ADDRESS 100H
GTV372VCR ORION CHASSIS MICRO OEC0093B
GTV373VCR COMBI
GTV373VCRBLUA COMBI LOPTX(043213012R JVC) ARCING
GTV373VCRBLUA COMBI SCAN COIL ARCING(BEEN IN CARAVAN OVER NIGHT)
GTV376VCR 2004
GTV376VCR COMBI ORION OR SAMSUNG ? LOTS OF CP005 NUMBERS
GTV376VCR COMBI STBY PSU OK, LOPTX(FNI14B001)
GTV376VCR COMBI STBY PSU OK, MICROPRO(ORION)
GTV400 GRUNDIG G1000
GTV401 GRUNDIG G1000
GTV42P4 PLASMA PSU NOISE BEKO
GTV42P4 PLASMA PSU NOISE/BLOCKY PIC, U454(LM2576S 453007)
GTV48T2 PT11 (??)
GTV51N1
GTV51N1 11AK19 SEE VESTEL EEPROM(24LC08B)
GTV51N1 11AK19 REMOTE
GTV51N2DVD VESTEL 11AK30
GTV51N2DVD 2004
GTV51N3BLU4 SEE VESTEL 11AK19
GTV51N3BLU4 11AK19 REMOTE
GTV51NDVD 11AK?? +DVD 2004,
GTV601 POOR SND,C917,R619(0R68),D905
GTV62W1SIL 11AK37-11
GTV62W1VPL NOISE/WHISTLE FROM CHASSIS ,L603
GTV66N1 VESTEL 11AK19
GTV66N3 11AK19P4
GTV66W1
GTV66W1 VESTEL 11AK19
GTV66W1 VESTEL 11AK19 NO PIC BEAMLIMITER C604(47NF63V) S/C
GTV66W1 11AK19-08A LOPTR(BU2508AF NOR NOD)+TCDT1102G/CQY80NG 150VN
GTV66W1 11AK19 POOR EW WIDTH R629(2R7)
GTV66W1 11AK19 SEE VESTEL.TV
GTV66W1 11AK19B1 MICRO SDA5457-B001
GTV66W1 LOPTR(BU2508AF) +JOINTS AROUND
GTV66W1 LOPTR+BUK444-200 LINE DRVR.
GTV66W1 WIDE SCREEN TURKEY 9 SCREWS
GTV66W2 28ZKQ 4400
GTV69RF2 11AK37-10 (10019793) 2003
GTV69W2DT 11AK33 WITH DIGIBOX 2004
GTV69W3 VESTEL 11AK19
GTV69W3 11AK19 EAST WEST DISTORT R629(27R)+430NF250V
GTV69W3 11AK19 DEAD TICKS LOPTR(2SD2579/BU2508AF),C626,R629(3R3)
GTV69W3 11AK19 SEE VESTEL
GTV69W3 11AK19 SWITCHING FROM NICAM TO MONO THEN NO SND VL301 ON NICAM PCB
GTV69W3 LO WIDTH EW RASTER R629(27R)
GTV69W3(11AK19)
GTV69W3BLK 11AK37-8 2002
GTV69W3BLU4 11AK19PRO DEAD LOPTR(BU2508AF)+EW (BUK444-200A/PNQ20T) CAUSE C630+D611(BY299P)
GTV69W3SIL 11AK19PRO OR 11AK37 11AK37 AFTER 2002
GTV69W3VPL VESTEL 11AK37
GTV69W4SIL VESTEL 11AK37
GTV69W5SIL 11AK19P5 OR 11AK37 11AK37 AFTER 2002 AK19 PROD.CODE:10014298, AK37 PROD.CODE:10014462
GTV69W5SIL VESTEL 11AK37
GTV69WZDT DEAD IC106(MC44608P40
GTV76RF1 11AK37-10 (10019792) 2003
GTV76W
GTV76W1 11AK19
GTV76W2DT 11AK33 VESTEL
GTV76W2SIL 11AK19P2, 11AK19P5
GTV76W2SIL 11AK19PRO EW LO WIDTH,R629(56R),C630(680NF GOES LO).
GTV76W2SIL 11AK19PRO TDA6108JK RGB R914(47R) ON TUBE BASE.
GTV76W2VPLSIL SEE 11AK19 VESTEL
GTV76W4SIL 11AK37-6 2002, 2003
GTV76W4SIL 11AK37 VESTEL 145VN
GTV9151
GTV9151 EHT CRACK , CRT FAULT
GTV9200 SAMSUNG C1125
GTV9200 WARM BRILL, C801(2N2F1KV)
GTVL32W25HD
GVT66W1 11AK19 LACK OF WIDTH & E/W FAULTY R629(2R7 SAFETY RES)
GVT66W1 11AK19 SEE GOTO VESTEL
K2105
K2105 11AK30A4 2003 2004
K2105 VESTEL 11AK30GOTO VESTEL
K24W10 2004
K2805 11AK37 SEE GOTO 11AK37
K2805 11AK37 FIELD COLLAPSE CAUSE LG.PHILIPS CRT
K28W05 2003/2004
K28W05 VESTEL 11AK37-10
K28W05 VESTEL 11AK37-11. FIELD COLLAPSE D616 (RGP15J),R675(0R47)
L6.3 286NS E/W DIST & LACK OF WIDTH CAP 2913 390NF 250V & MOSFET TR 7908 STP4NA40F1
LD1501 ALLSORTS GREEN PINK,WHITE,PIC FREEZES,NOISEY PIC,NOISEY, C908 1000UF16V
LD1501 NO GREEN LED ,EEPROM
LD1501 NO PIC DRY JOINT ON L2 ON INVERTER PCB
LD1501 VESTEL 17MB01P-2
LD1928W SCRN FLASH THEN OFF,PSU/INVERTER PCB(LS1904006A) TRUTECH
LD2002 VESTEL EXTERNAL PSU 4 PIN,0219B1275 CHASHYDE(12026QC) 6A25 12V
LD2002 DEAD/STBY XTERNAL PSU 0219B1275 CHAS HYDE
LD2002 WARM NO PIC,PSU UNIT0451B1270 FROM CHAS HYDE
LD2650 LCDTV RED LED FLASHES C315(1000UF25V) ON PSU
LD32 PSU BOARD (04TA069I 841170032413) FROM OHMSUPPLIES
LD3250HD (IC BLOWN FSD200 V602) +SECONDARY ELECTROLYTICS
LD3250HD DEAD PSU IC21(FSD200),IC30(ICE1QS01),D325/D326(IN4007),300(BC337)D318(2V4 ZD),D315(12V ZD)FUSE3.15
LD3250HD PSU(841170032441 32165) PSU(841170032416 04TA069J 24001YC)
LINK13 ON PSU.
Q9001 ALBA PTV9C SAMSUNG BT110
Q9001 ALBA PTV9C SAMSUNG BT110
RC7051 LG D17 CHASSIS
SAL1903/9 C134(17N4F 1600V[22N])+D15(BY228) CHOPPERTR(S2000N/AF) EW(TDA4950).
SD1800 CHILDLOCK PRESS "STBY" "SYSTEM" TOGETHER
SD1800 CHILDLOCK PRESS "STBY" AND "SYSTEM" TOGETHER
SGTV69W3 11AK19 INT NO SND VL301 NICAM PCB
TCV141 CP420 DEAD R831,SW08
TD1540 TV+DVD 2003
TV14RC DEAD STBY TX O/C PRIMARY.
TV14RC KFS60226B.
TV14RC SQUEAL C418/R400 /L403 BURNUP.
TV14T3DVD DEAD/STBY HOT CHOPPER, LOPTR
TV20RC
TV20RC DEAD SET. R802 .
TV20RC DEAD. R802 .
TV20RC FIELD COLLAPSE. R326(3OHM) SAFETY .
TV20RC FRAME COLLAPSE. R326(3R3)
TV20RC NO PIC R430 10R 180V LINE
TV20RC NO PIC R430 10R IN 180V SUPPLY TO RGB
TV20RC NO PICTURE. R430 10R IN THE 180V SUPPLY TO THE RGB OUTPUT TRANSISTORS
TV20RC NO SND OR RASTER - SBY LED & CH INDICATOR OK. R801(3.3OHM 10W) , Q801(STR5412) , D805(1N4937 .
TV20RC NO SND R601 560R
TV20RC NO SND. R601 560R, 1W
TV20RC NO SND/PIC LED & CH OK. R801(3R3 10W),Q801(STR5412),D805(1N4937) .
TVC LOPTX(FSA36012M=FBT40491=11725077A=HR7880)
TVC100S COMBI 2004
TVC1400
TVC1400 COMBI DAEWOO CP310
TVC1400 CP310 (DAEWOO) FERGUSON FG14CB12V DAEWOO DVT1484D
TVC1400 DEAD FOR DRY JOINTS ON C817
TVC1400 DEAD C817(100UF25V)
TVC1400 DEAD MAINS SWITCH ON SIDE
TVC1400 DEAD PSU PULSING C817(100UF25V),C811(100UF63V)
TVC1400 POOR BRIGHTNESS LOOKS LIKE CRT C543 10UF250V ON CRT BASE
TVC1400 POOR CRT C543 10UF250V ON CRT BASE
TVC1400 TRIPPING LED FLASHING C811 IN POWER SUPPLY
TVC1400 TRIPPING LED FLASHING C811(100UF63V) IN PSU
TVC1400 TRIPS WHEN FIRST SW ON C811 100UF 25V NEXT TO CHOPPER TR
TVC141
TVC141 DAEWOO CP420.
TVC141 CHILDLOCK BLUE/YELLOW/GREEN/RED/STANDBY/STANDBY WITHIN 10
TVC141 CP420 (DAEWOO, K-MECHA DECK)
TVC141 DAEWOO CP420 DAEWOO DVT14F5
TVC141 NO PIC OR SND (BLANK RASTER) MICRO AND ENTER SERVICE MODE AND SET LEVELS,(IC703)
TVC141 NO PIC/SND RESET EEPROM SERVICE MODE SET LEVELS,(IC703)
TVC141 VOLUME LOCKED EEPROM
TVC141/142 VOLUME LOCKED EEPROM
TVC142
TVC142 VOLUME LOCKED EEPROM
TVC142T CP420 (DAEWOO, K-MECHA DECK)
TVC142T DAEWOO CP420 DVT14F6PSU
TVC143TS COMBI DAEWOO CP08?
TVC143TS COMBI NO SND EARPHONE SOCKET
TVC143TS CP082 (DAEWOO) 2003,
TVC145T COMBI CP420 DAEWOO
TVC145TW CP420 (DAEWOO, K-MECHA DECK) DAEWOO DVT14F8PA
TVC146 COMBI,POWER SWITCH SW08
TVC146T CP420 (DAEWOO, K-MECHA DECK)
TVC146TWS COMBI DEAD STRS5707
TVC146TWS CP420 (DAEWOO, K-MECHA DECK) DAEWOO DVT14F6PA
TVC146TWS, DAEWOO CP420 DEAD LOPTX SMOKING
TVC147TWS CP082 (DAEWOO) 2003,
TVC14PV DEAD C807, C811 (100UF 16V), C831 (470UF 25V), C814 (1UF 50V), D2499 (BU508AF)
TVC14VP COMBI DAEWOO CP310
TVC14VP COMBI DEAD RELAY CLICK,CHOPTR VR801(4K7),D807(BYV95C),TDA4601,270K.
TVC14VP COMBI,TUNER DRIFT,33V REG(UPC547J),C837(47UF50V)
TVC14VP CP310 (DAEWOO) FERGUSON FG14CB12V DAEWOO DVT1484D
TVC14VP DAEWOO CP310 COMBI
TVC14VP DEAD C807(180UF400V)
TVC14VP DEAD, TRIPPING C807 MAIN SMOOTHER (180UF400V)
TVC14VP DEAD,C811(00UF16V)IN PSU
TVC14VP INT NO AUDIO / R618
TVC14VP INT NO SND R618
TVC14VP LIKE DAEWOO DVT1482P(CP310 )
TVC14VP POOR PIC AND NOISY R217 6.8K FOR HIGH VALUE
TVC14VP POOR PICTURE R217 6K8
TVC14VP STBY - RELAY CLICKS AT SW ON HT POT VR801 4K7, D807 BYV95C, Q801 2SD1555 & I801 CHOPPER CHIP TDA4601 & FOR DRY JOINTS
TVC201T
TVC201T COMBI DEADISH LOPTX NOISE,TDA6107Q ON CRTBASE PCB
TVC201T COMBI EXCESS BRILL/FLYBK, R916(47R),TDA6107G/TDA6108VF
TVC201T CP420 (DAEWOO, K-MECHA DECK)
TVC201T DAEWOO CP420 GOTO DAEWOO
TVC201T DEAD RELAY/LEDS CLICKING,C840(47UF)
TVC201T DEAD TICKS,LOPTX(FSA36012M/HR7880)
TVC201T NO PIC C413(10UF250V)
TVC202TS COMBI
TVC202TS CP082 (DAEWOO) 2003,
TVC202TS DEAD,I801(STRF6707),D808(ZENER), R810, R809, R808
TVC202TS DEAD,STRF6653 ,R908(0R27),D806,Q801,Q802(KTC3207),D808(IN4937G) SCR(I822(X0202DA))
TVC202TS DEAD,TDA6107JF(FUSSY)
TVC46 COMBI DEAD,SWITCH SW08 RESOLDER
TW28D11 2003/2004
TW28D11 CF885F DAEWOO CP85F/WP895F LOPTX(ELDOR 13625024A) SPARKING INSIDE
TW32D11 2003 GOTO DAEWOO
TX1200 DRUM TOO FAST 104K R525 NR SERVO IC.
U2KA83NC4W6 TRIPS LOPTR(S2050) +RESOLDER AREA
UG00N75N45W300 F28
UG0FL37M12G230 SEE GOODMANS 1490T-IB
UGOKR83N45W00 W325NS-T ITALY
UGOKR83N45W00 W325NS-T FPC2001 ITALY SEE FORMENTI
VN6000 DEAD - ORIG INT DEAD C822 & 823 IN PSU LOW CAP
VN6000 DEAD C822 IN POWER SUPPLY 330UF63V
VN6000 DEAD C822 330UF63V,C823 IN PSU
W228NSA SEE FORMENTI F19
W280NS
W280NS SEE FORMENTI F19
W280NS F16 OR F19 (DEPENDS ON THE YEAR)
W280NS F19 ELDOR LOPTX ARCING (1372.0052/0052A)
W280NS F19 ELDOR LOPTX ARCING (1372.0066A/HR8770)
W282
W282NS-T "TWIST" CHASSIS.
W282NS-T NOT F19 BUT FORMENTI FPC2001 KNOWN AS "TWIST" CHASSIS.
W282NS-T FPC2001 (FORMENTI-SELECO)
W282NS SEE ALSO PROLINE 28N1 AND FORMENTI REMOTE-=IRC81408
W282NS F19
W282NS DEAD LOPTR(S2055N),D25(BA159),C70(0U22F400V)
W282NS F19
W282NS F19 FORMENTI
W282NS FORMENTI F19 E-W BOWING ON ALL MODES,C71(??)
W288NS FORMENTI
W288NS Goto F16 SOME ARE FORMENTI F16
W288NS Goto F19 SOME F19
W288NS F16 OR F19 (DEPENDS ON THE YEAR)
W288NS TOPTEL124 REMOTE=IRC81408
W288NSA FORMENTI F19 REMOTE=IRC81408
W321
W321NS-A F19 LOPTX 1372.0052A (EQUIV. 1362.5001A, HR8770, FBT40828)
W321NS GOTO FORMENTI F16
W321NS F16 OR F19 (DEPENDS ON THE YEAR) REMOTE=IRC81408
W321NS LOPTR CAUSE FLASHOVER IN CRT BASE SOCKET
W322
W322NS
W322NS SEVICE MODE TV OFF ,HOLD TV VOL+ AND REMOTE STBY AND SWITCH ON PROG,STORE = YELLOW
W322NS F19
W322NS F19 FORMENTI
W322NS F19 LOPTX Goto F19
W322NS LOPTX 1372.0066A
W322NS LOPTX FBT40828/1372.0052/1362.5002/1362.5001/13720052A/13625005D
W322NS S19 NO PIC SND OK,R35(12K)
W322NS SEVICE MODE TVOFF, HOLD TV VOL+ AND R/C STBY AND SWITCH ON MAINS,YELLOW=STORE
W322NS SEVICE MODE,HOLD IN VOL+ ON TV AND R/C STBY, SWITCH ON AT MAINS SWITCH
W322NS TRIPPING,LOPTX AND LOPTR(S2055N),CAUSE C68(15NF1K6V CPC=CA00725)
W325
W325NS-T FPC2001 (FORMENTI-SELECO) 2003
W325NS-T FPC2001 DEAD DEGAUSS POSISTOR
W325NS GOTO FORMENTI
W32NS
W32NS LOPTX ARCING 13720052A/FBT40828 1362.5005D/FBT40860
W32T1
W32T1 PT192-DEAD. RP06 3M9 IN PSU
W32T1 PT92
W332NS F19 FORMENTIGOTO F19
W336NSA INT NO PIC,C73
W431NS BUSH/PHILIPS REMOTE
WS322NS DEAD LOPTR
WS32T1 DEAD 320V OK NO HT FROM PSU, RP06 3M9
ZX NO FIELD. R401 (1R) .
ZX NO FIELD. R401(1R) .
GOTO TOP
If you know of any fault repairs NOT here. Please email the info to me
your fault NOT here , try my step by step guide
Do it yourself guide
Highlandelectrix