Press CTRL/F to search this page (no -)

 HOME_PAGE   

BUTTON TO STORE
GOTOHREF="/tvs/FERGUSON.TV.html">TO FERGUSON FILE

ICK2 EHT SURGE/STBY LOPTR HOT,TL082
ICK2 TRIPPED PIN 40/TA8659CN 9V = ON,0V = STBY/TRIP FROM TR17 BC558C
IDC2 NO SOUND TS40,TS41,TS42,TS43
IKC1 SCAN COILS OVERHEAT THO PIC OK SCAN COILS FAULTY
IKC2
 IKC2 A51F DEAD - LED FLICKERS TWICE BRIEFLY LOPTX
IKC2 A51F SND LO CS14(1UF63V)
IKC2 A51F SND LOW WEAK AUDIO O/P AT PIN 10 IF CAN,CS14 1U 63V IN THE CAN LOW CAP
IKC2 A51F TUNING PRESS/HOLD THE PROG BUTTON ON STARTUP,RED FASTTEXT
IKC2 ARCING LOPTX,DISCON(TV01) EARTH PIN 20 MICROPRO IR01 TO CHASSIS TO FORCE ON TF25
IKC2 BLOWS CHOPPER TRS CP29 2N2 IN SNUBBER NETWORK - SWOLLEN AT LEG
IKC2 BRIGHT PIC RL05(100K)
IKC2 CHOPPER+CP29(2N2F)
IKC2 CHOPTR CP29 2.2NF
IKC2 COLD VERT SHIFT IF01 TL082/CP
IKC2 CONTRAST 2 HIGH,RR41=6K8,RR42=18K,RR43=8K2,RR44=5K6,RR45=8K2,RR46=15K
IKC2 DARK PIC TT33 ON CRT BASE
IKC2 DEAD - CL44 IN LINE - BLEW S2000 LOPTR FUSIBLE IN 220V SUPPLY TO RGB O/P STAGE
IKC2 DEAD - EMITTER OF TP18 BELOW 21V. DP16(1N4148)
IKC2 DEAD - TRIPS AT SW ON TV01 BC558 CAUSED BY ARCING LOPTX
IKC2 DEAD 112V OK,NO LINE DRV,TV01 BC558C CAUSE LOPTX ARCING TA8659CN
IKC2 DEAD CHOPTR CP29(2N2)
IKC2 DEAD CL44 OPTR
IKC2 DEAD CL44 S2000 LOPTR
IKC2 DEAD DP16(IN4148)
IKC2 DEAD DP16(IN4148),TV01
IKC2 DEAD DP50(BY399)
IKC2 DEAD DR83(1N4148),DP16
IKC2 DEAD EHT SURGE,TVO1 BC558 CAUSE LOPTX ARCING
IKC2 DEAD FOR 21V AT EMITTER TP18 IF LOW DP16 FOR(IN4148)
IKC2 DEAD FUSE ON/OFF SW DEGAUS POSISTOR
IKC2 DEAD IF01B TLO82,TF16
IKC2 DEAD IV01(T8659)
IKC2 DEAD LED PULSES TV01(BC558)
IKC2 DEAD LOPTR(S2000)+CL44
IKC2 DEAD ON/OFF+DEGAUSS
IKC2 DEAD RED LED PULSES TV01(BC558)CAUSE LOPTX
IKC2 DEAD SURGE IF01B TLO82,TF16
IKC2 DEAD TR16(BC548B),TR17(BC558B)
IKC2 DEAD TV01 BC558 CAUSE ARCING LOPTX
IKC2 DEAD TV01(BC558) LOPTX
IKC2 DEAD(STARTS BUT SHUTS DOWN) IF01B TLO82,AND TF16
IKC2 DEAD,STBY OK TV01- ATTENUATING DRIVE O/P FROM LINE DRIVER
IKC2 DEAD/STBY R16(BC548B),TR17(BC558B)
IKC2 DEAD/TRIPS LOPTX ARCING,TV01(BC558)
IKC2 DEAD/TRIPS TLO82,TF16
IKC2 EHT BURST,TV01(BC558),CAUSE LOPTX SPARKING
IKC2 EHT SURGE/STBY TL082 CHIP CURED THE FAULT
IKC2 FIELD COLLAPSE TF25(BC548) CAUSE LOPTX
IKC2 FIELD COLLAPSE TF25(BC548),CAUSE LOPTX ARCING
IKC2 FIELD COLLAPSE TF25,A BC548,IN THE FIELD RAMP GENERATOR WHICH WAS CAUSED BY LOPTX ARCING
IKC2 FIELD FOLDOVER DF16
IKC2 FIELD FOLDOVER DF16(BY398)
IKC2 FIELD FOLDOVER. DF16(BY398)
IKC2 GOES STRAIGHT TO STBY IFO1 SC DF16 SC
IKC2 GOING IN TO STBY AFTER FEW SECONDS. DL11(BA157),RL11(15R) LH SIDE OF LOPTX
IKC2 HI CONTRAST RR41=6K8,RR42=18K,RR43=8K2,RR44=5K6,RR45=8K2,RR46=15K
IKC2 HOT STBY TV01(BC558C)+TV02(BC548C)
IKC2 HT PULSING TV01,TV02 AND TV17 CURED THE FAULT
IKC2 HT.OK IV01(T8659) 9V = ON 0V = STBY TRIP VOLTS COME FROM TR17
IKC2 INT STBY AFT LONG TIME TV01 BC558C & TV02 BC548C TRANSISTORS
IKC2 INT STBY AFT LONG TIME TV01 BC558C TV02 BC548C TRANSISTORS
IKC2 INT STBY CHOPPER H/SINK EARTHS
IKC2 INT STBY RP26
IKC2 INT STBY TV01 BC558C TV02 BC548C
IKC2 INT TRIP MOD RP26 FROM 2K2 TO 1K5(ADD 4K7 ACROSS IT)
IKC2 LOW BRIGHTNESS - DOESN'T ALTER WITH OSD TT33 ON CRT BASE
IKC2 LOW BRILL TT33 ON CRT BASE
IKC2 NO CONTRAST RL05
IKC2 NO LINE DRV,TDA8178F
IKC2 NO RESULTS NO STBY LED. DP50(BY399)
IKC2 NO STARTUP. TR16(BC548B),TR17(BC558B)
IKC2 NO TEXT TP66(ESM740)
IKC2 OFF WITH BANG MAINS FUSE SHATTERED,ON/OFF SW SIEZED - CAUSED BY DEGAUS POSITOR
IKC2 OSD="PRO MO" HOLD VOL+,THEN STBY
IKC2 OSD=P1/NO REMOTE RESET HOLDCHANUP/CHANDWN AND POWER ON
IKC2 PIC TEARING,CRACKLING NOISE LOPTX/FOCUS UNIT
IKC2 POOR SND,CS14(1UF63V) TWEEN PIN7 14 OF IF-CAN
IKC2 SBY,WORKS IF FIELD COIL PLUG RE DF16 BY398SC
IKC2 SND PLOP ON STBY CA15 10UF
IKC2 STBY - LOCKED IN STBY. PRESS PROGRAMME UP BUTTON ON FRONT UNIT FOR 6 SECONDS
IKC2 STBY - SWITCHING TO STBY ON CHANNEL CH. 2.2K RP26 WITH A 1.5K IF ANY LOWER BLOWS S2000AF
IKC2 STBY DF16 BY389 WAS SHORT-CIRCUIT
IKC2 STBY DF16(BY398)
IKC2 STBY DL11(BA157),RL11 TL082
IKC2 STBY DL11(BA157),RL11(15)
IKC2 STBY DL11(BA157),RL11(15R)
IKC2 STBY EHT SURGE IF01 TL082
IKC2 STBY EHT SURGE IF01 TL082IKC2 STBY PRESS TV PROG UP FOR 6 SECONDS
IKC2 STBY IFO1 DF16
IKC2 STBY IFO1 DF16 DL11(BA157) RL11(15R) NR LOPTX
IKC2 STBY ON CHANNEL . RP26
IKC2 STBY PRESS PROG UP BUTTON ON FRONT UNIT FOR 6 SECONDS
IKC2 STBY PRESS PROG UP ON TV FOR 6 SECONDS
IKC2 STBY RP26
IKC2 STBY SURGE EHT,IF01 TL082 FIELD DR CHIP
IKC2 STBY SURGE IF01 TL082
IKC2 STBY TL082 OP AMP IC
IKC2 STBY TL082IF01 WAS CIRCUIT,DF16 BY398
IKC2 STBY TR16(BC548B),TR17(BC558B)
IKC2 STBY TRIPPING,DL11(BA157)+RL11
IKC2 STBY TV01(BC558),FIELD CHIP IF01
IKC2 STBY,DF16 BY398SC
IKC2 SURGE/DEAD RESOLDER EVERYWHERE FIRST
IKC2 TRIP LED PULSES TV01(BC558)+LOPX
IKC2 TRIPPED PULSING HT,TV01 TV02 TV17
IKC2 TRIPPING - STBY LIGHT LIT. DL11(BA157),RES RL11
IKC2 TRIPPING DL11(BA157)+RL11(22R) TL082
IKC2 TRIPPING TV01(BC558),AND FIELD O.P. CHIP IF01
IKC2 TRIPPING TV01(BC558),FIELD IF01 CAUSE LOPX
IKC2 TRIPPING(RED LED) AT 1 SECOND INTERVALS. TV01(BC558),DUE TO LOPX
IKC2 TRIPS OFF AT SW ON TL082 OP AMP IC
IKC2 TRIPS SLOWLY(ONCE PER SECOND)TV01(BC558) BY MENT
IKC2 TRIPS TV01 BC558C+TL082 IF01
IKC2 TRIPS TV01(BC558)
IKC2 TRIPS TV01(BC558),IF01
IKC2133H DARK PIC RT33 6K8
IKC2133H WEAK SND DISPLAY RAMPS UP OK NOT FOUND
IKC27A OSD="PRO MO"HOLD"PR +/PR -" KEYBOARD,POWER ON,STBY
GOTO TOP If you know of any fault repairs NOT here. Please email the info to me
your fault NOT here , try my step by step guide Do it yourself guide
Highlandelectrix