Highlandelectrix DECCA.TV

Press CTRL/F to search this page (no -)

HOME_PAGE

'SKY REMOTE CODES DECCA 0244 065,100,544,300,277,245,272,077
HREF="HTTP://WWW.HIGHLANDELECTRIX.FSNET.CO.UK/tvs/TATUNG.TV.html">SEE TATUNG
10 BRADFORD VALVE SET PL802 PY800
10 BRADFORD
10 CONTRAST - VARYING ESP BETWEEN STATIONS. C60(22U F)
10 CONTRAST ALTERS C60(22UF)
100
100 BOTTOM CRAMP. D309,D310,D311
100 CHANNEL STUCK. R12(390K)
100 DEAD D600-3,RBA920,LOPTX,TRIPLER
100 DEAD FUSE FUSE HOLDER
100 DEAD FUSE. D617
100 DEAD LOPTR LOPTX TRIPLER
100 DEAD. D600-3,RBA920,LOPTX,TRIPLER D617
100 FIELD BOTTOM HALF BLANKED D302(IN4148)
100 FIELD D302(IN4148) D309,D310,D311
100 FIELD LO HEIGHT FOLDOVER BOTTOM. D309,D310,D311
100 NO CHAN CHANGE R12(390K)
100 ROPE EFECT RHS,TR304(BF355)
100 WILL NOT CHANNELS. R12(390K) ON TUNER PANEL
110
110 BRIGHTNESS VARIES R913(22K)
110 DEAD C624(100UF)
110 DEAD CHOPPER D608,D610,C627(10UF16V)
110 DEAD CHOPTR R637(2K2) TR604(8SR56)
110 DEAD FUSE CHOPTR. D608,D610,C627(10UF16V) R637(2K2),TR604(8SR56)
110 FLYBACK - BRIGHTNESS VARIES & FLYBACK LINES. R913(22K)
110 PIC ROLLS C308(10UF)
110 RED VERTICAL STRIPES. C208(22UF)
110 RED/GREEN/BLUE WITH FLYBACK LINES R913(22K)
110 SYNC POOR. C308(10UF)
110 TRIPPING. D602(ZPD22),R636,C633(680UF),IC61
110 TRIPS C617(68NF)
120
120 CHANNEL CHANGES. FOCUS SPARK GAP ON CRT BASE
120 CONTRAST WEAK. R425 R426(68K)
120 CRAMPED FIELD R813(10K)
120 DEAD BU426A,R810(150K)R808(47K)C406(22UF)
120 DEAD C406(22UF)
120 DEAD FUSE CHOPTR R808 R810
120 DEAD HISSING NOISE - TRIPLER
120 DEAD Q801,R808(47UF),R810(150UF)
120 DEAD R430 TRIPLER
120 DULL PIC/CONTRAST R425 R426(68K)
120 FIELD COLLAPSE. D404(BA159),R434(10R),IC301(TDA1170S)
120 FIELD CRAMP R813(10K)
120 LINE HOLD TDA2576A,C406(22UF16V)
120 NO COLOR. C517(100NF) R226,R244,R251
120 NO LUMA C514(100NF)
120 NO REMOTE STBY IC SAA1351
120 NO STBY,SAA1351
120 NO TUNING HIGH SND. TRIPLER
120 POOR CONTRAST R425,R426(68K)
120 POOR START C804(220UF385V)
120 RANDOM CHANNELS,FOCUS SPARK GAP ON CRT BASE
120 SYNC LINE,OFF C406(22UF)
120 TRIPS C804(220UF385V)
120 TUNING RM17(560K) BF959(IF PREAMP)
125
125 CRAMPED FIELD R813(10K)
125 FIELD COLLAPSE IC301(TDA1170S),R434(10R)
125 FIELD CRAMP R813(10K) SET HT CONTROL
125 LINE HOLD TDA2576A,C406(22UF16V)
125 NO COLOR.C517(100NF)
125 NO LUMINANCE. C514(100NF)
125 NO STBY SAA1351
125 POOR CONTRAST R425,R426(68K)
130
130 BEAM LIMIT FAULT,CONTRAST WEAK. R425 R426 BOTH(68K)
130 CHANNEL CHANGE INT. FOCUS SPARK GAP ON CRT BASE
130 CONTRAST WEAK. R425 R426 BOTH(68K)
130 DEAD C816(100UF)
130 FLYBACK LINES R436+ C427
130 GREY SCALE R226,R244,R251(100K)
130 INT STBY,STBY TRANSFORMER
130 PIC ROLLS,C402,C403,C406,C407
130 POOR PIC SND OK. R226,R244,R251
130 SNOW. RM17(560K)
130 TRIPPING R816(100R)
130 TUNING SNOW. RM17(560K) BF959(IF PRE AMP) R68(33K)
140
140 BRIGHT PIC R436 C427
140 COLOR INT. Q211 Q203
140 DEAD C813
140 DEAD C813 C807 C808(100UF25V) D805 D802 D811 R805(390K)
140 DEAD FUSE Q801 C425(86NF),D811
140 DEAD FUSE Q801,C425(8.2NF OR 8.6NF),D811
140 DEAD FUSE,ON OFF SWITCH
140 DEAD LO HT C807 C808(100UF25V)
140 DEAD PCB TWEEN D805 & D802
140 DEAD R805(390K)
140 FIELD BOUNCE IN TXT PIN 8 CONNECTOR M501
140 FIELD COLLAPSE R434(10R)
140 FIELD LO HEIGHT ROLL. R423(2R2)
140 FIELD ROLL R423(2M2)
140 INT CHANGES CHAN FOCUS SPARK GAP
140 INT CHANNEL CHANGE ON ITS OWN,FOCUS SPARK GAP
140 INT COLOR Q211 Q203
140 INT SNOWY Q101(BF959)
140 INT START UP R805 390K HI RES ALSO R802 10K DRY JOINTS
140 INT START UP R805(390K) R802(10K)
140 LO HEIGHT/ROLLS. R423
140 LOUD HUM AT SW ON WITH NO PIC C807,C808 & C810 100UF25V
140 LOUD HUM AT SWITCH ON. C808 & C810(100U F,25V)
140 LOUD HUM C808+C810(100UF,25V)
140 LOUD HUM NO PIC C807,C808 C810(100UF25V)
140 LOUD HUM NO PIC C807,C808+C810(100UF25V)
140 NO FUNCTIONS - HT OK. R817(220R SAFETY)
140 NO PIC R817(220R)
140 NO PICTURE. R817(220R)
140 NO TUNING 68(33K),R003(13K),70(33K)
140 NO TUNING RR70(33K)
140 NO TUNING RR70(33K)R68(33K),R003(13K),R70(33K)
140 NO TUNING/SIGS NO TUNING VOLTS PIN 4 TUNER - RR70 33K
140 NOT TUNING IN. 68(33K),R003(13K),70(33K)
140 PIC GOES RED INT R224(1K) PRESET
140 PIC RED INT R224(1K) PRESET
140 PICTURE GOES TO SNOW AND SOUND COMES UP LED CHANNEL DRY JOINTS ON 5V RAIL OR ON CHOPPER TX
140 POOR START C808(100UF)
140 POOR START R805(390K) R802(10K)
140 RAGGED VERTICALS C822 &C826 47UF250V
140 RAGGED VERTICALS C822 C826(47UF250V)
140 RAGGED VERTICALS C822 C826(47UF250V)140 SLOW START C807,C808 C810(100UF25V)
140 REMOTE CONTROL - NONE+FLICKERING LED DISPLAY. DJ WHERE CONNECTED TO 5V LINE ON DISPLAY PANEL
140 SLOW START C807,C808+C810(100UF25V)
140 SLOW START UP WITH CRACKLING C807,C808 & C810 100UF25V
140 SNOW BF959(IF PRE AMP)
140 STANDBY - NO SWITCH ON FROM STANDBY. IC SAA1351,THE TRIPLER MAY BE TO BLAME
140 STBY IC SAA1351,CAUSE TRIPLER
140 STBY SAA1351 CAUSE TRIPLER
140 STBY SAA1351,TRIPLER
140 STREAKY PIC D403(BA159)
140 STREAKY PICS D403 BA159 200V RECT DIODE
140 TAKING UP TO 2 MINS TO COME ON. 2 BY 100UF25V CONS,& 1 BY 100K RES ADJ TO TDA4600
140 TRIPPING - RECYCLING. MICA WASHER BREAKING DOWN
140 TRIPS POOR START OR NOISY START UP C808 100UF(PIN 9 4600)
140 TUNING - NO SIGNALS. BF959(IF PRE AMP)
140 TUNING - NO TUNING. 70(33K)
140 TUNING SNOW BF959(IFPRE AMP) R70(33K)
140 VERT RAGGED. C822,C826(47UF250V)
140 VERTICALS RAGGED C822,C826(47UF250V)
140 VERTICALS RAGGED. HT & SMOOTHING CONS C822,C826 BOTH 47UF,250V
140 WARM DEAD C813
140 WON'T SW ON FROM STBY SAA1351 R/C CHIP - ALSO TRIPLER(OK WHEN R/C CCT BYPASSED)
141
141 FIELD - ROLL - CONTROL UP ONE END. R423(2.2M 1/2W)
141 FIELD ROLL R423 2M2 磕
141 FIELD ROLL R423(2M2)
145
145 /150 NO FIELD. R434(1.2R) BY LOPTX
145 BRIGHT RASTER R436 10R FUSIBLE
145 BRIGHT RASTER R436(10R)
145 COLD TRIPS C808(100UF)
145 DEAD - BLOWING CHOPPER TRANSISTOR. R808(100K) & R810(82K)
145 DEAD - CHOPPER TR FAILURE R808 100K,R810 82K
145 DEAD CHOPTR R808(100K) R810(82K)
145 DEAD CHOPTR R808(100K),R810(82K)
145 EXCESS BRILL R436(10R)
145 FIELD COLLAPSE R434(10R)
145 FIELD COLLAPSE R434(1R2)
145 FIELD COLLAPSE.R434(1R2)
145 NO FIELD. R434(1R2) NR LOPTX
145 NO PIC HUM ON SND C808(100UF)
145 NO PIC HUM ON SOUND C808 100UF
145 NO RASTER WITH MUFFLED SOUND(FIELD COLLAPSE) R434 10R FUSIBLE FIELD O/P SUPPLY
145 NO TUNING,68(33K)R003(13K)
145 NO TUNING. 68(33K) AT FRONT L/H SIDE,ALSO R003(13K,1W)
145 NO TUNING. R68(33K) R003(13K)
145 SLOW START R816(100R)
145 SLOW START R816(100R)C808(100UF)
145 SLOW START UP R816 100R 1W INT
145 STBY. R802,R809(82K)
145 STUCK IN STANDBY. R802,809 82K OC
145 TRIPS AT SW ON UNTIL WARM C808 100UFIN PSU
145 TUNER DRIFT M293AB1
145 TUNING DRIFT M293AB1 IR03
145 TUNING DRIFT M293AB1 IR03 TUNING VOLTAGE SYNTHESISER
145 TUNING DRIFT M293AB1 TUNING SYNTH CHIP IR03
145A CHANNELS - INT CHANNEL . FOCUS GAP FLASHING OVER ON CRT BASE
145A FAST TRIPPING FROM COLD. C808(100U F,25V) BY TDA4600
145A FAST TRIPPING FROM COLD. C808(100UF,25V)
145A INT CHANNEL CHANGE. FOCUS GAP FLASHING OVER ON CRT BASE
145A INT CHANNEL FOCUS GAP ARCING CRT BASE
145A NO FIELD. R434(1.2R) BY LOPTX
145A NO FIELD. R434(1R2) BY LOPTX
145A TRIPS C808(100UF25V)
146
146 BLANK RASTER D502(5V6 ZD)
146 BLANK RASTER D502(5V6 ZENER)
146 BLANK RASTER PIN 7 TDA3561 LOW - D502 BZX79C5V6 ZENER
146 FIELD COLL. THEN NO PICTURE R434 OC(FIELD) D502 SC(5V6 ZENER) PICTURE
146 FIELD COLLAPSE OR BLANK RASTER R434,D502 BZX79C5V6
146 FIELD COLLAPSE R434 D502(5V6 ZENER)
146 FIELD COLLAPSE R434,D502 BZX79C5V6
150 TATUNG TV9448
150 TATUNG TV9448
150 COL FAULT - LIKE HANOVER BARS ACC DECOUPLER C516 4UF7 U/S
150 COLOR- ALTERNATE BARS OF COLOR& NO COLORAGC DECOUPLER C516(4.7UF)
150 COLOR C516(4U7)
150 COLOR HANOVER BARS C516(4U7F)
150 FIELD COLLAPSE.R434(1R2)
150 NO FIELD. R434(1R2) NR LOPTX
150 TATUNG TV9448
160 TASHIKO 16E891
160 TASHIKO 16E891
160 BLANK RASTER FLYBACK LINES R410(10R)
160 BLANK RASTER SND OK. R410(10R)
160 BLANK RASTER WITH FLYBACK LINES - SOUND OK. R410(10R)
160 COLD BOTTOM CRAMP TDA4503
160 COLOR INT. IC TDA3565
160 COLORINT. IC TDA3565 DECODER IC
160 CONE SHAPED RASTER. LOPTX
160 CONE SHAPED RASTER. LOTPX
160 DARK BAND 1-2" ACROSS CENTRE OF SCREEN. C303(220NF)
160 DARK BAND ACROSS C303(220NF)
160 DARK BAND C303(220NF)
160 DEAD - BLOW UP DUE TO EXCESS HT LOPTR BU508 & TDA3651 FOP CHIP - D808 IN SET HT
160 DEAD - FUSE BLOWN. CHOPPER TX(R4051),D812(BY396),R802(3.3R 4W)
160 DEAD - FUSE BLOWN. POSISTOR,1.25AMP
160 DEAD BU508 TDA3651 D808
160 DEAD CHOPTR(R4051),D812(BY396),R802(3R3 4W)
160 DEAD CHOPTX(R4051),D812(BY396),R802(3R3)
160 DEAD H.T. OK BUT 11.5V TO SIGNAL CIRCUIT MISSING Q501 & R508(10K)
160 DEAD HT AT CHOPPER TR COLL L802
160 DEAD L802
160 DEAD LINE TR R411 BURNT UP FIELD IC MAY ALSO D808 IN SET H.T. 117V
160 DEAD LOPTR BU508+TDA3651/TDA3653B+D808
160 DEAD LOPTR R507 R508(12K)
160 DEAD LOPTR,R507 R508(12K)
160 DEAD LOPTR,R507/508 12K
160 DEAD NO LINE DRIVE Q503 R508(12K)
160 DEAD POSISTOR
160 DEAD Q501 R508(10K)
160 DEAD Q501+R508(10K)
160 DEAD WITH HT. BUT NO LINE DRIVE DRIVE AT BASE LINE OUT TR CHCK FOR 12V Q503 & R508(12K)
160 DEAD(ISH)R508(12K)
160 DEAD,PSUPP TICKING R8050 OC. 100K
160 DEAD,TICKING R8050(100K)
160 DEAD. L802
160 FAST TRIPS R507+R508
160 FIELD COLLAPSE R301 560K HI RES
160 FIELD COLLAPSE R301 560K ON PIN 1 TDA4503
160 FIELD COLLAPSE R301(560K)
160 FIELD COLLAPSE R411
160 FIELD COLLAPSE R411 IC301
160 FIELD COLLAPSE TDA3561(TDA3563 WORKS) U/S & R411 10R SAFETY RES
160 FIELD COLLAPSE TDA3651 FIELD CHIP U/S
160 FIELD COLLAPSE TDA3651(TDA3653 DOES);R411 10R
160 FIELD COLLAPSE TDA3651/TDA3653 R411(10R) R301(560K)
160 FIELD COLLAPSE TDA3651/TDA3653B/TDA3653+R411(10R)
160 FIELD CRAMP AT BOTTOM UNTIL SET IS WARM. IC TDA4503
160 FIELD CRAMP TDA4503
160 GHOSTING Z101 SAWF
160 HOT LINE SYNC C113(2700PF)
160 INT CUTTING OUT. DRYS ON Q801
160 INT DEAD DRY JOINTS Q801 EMITTER
160 INT DEAD Q801
160 INT SIGNALS R007 3K9
160 INT SIGNALS R007(3K9)
160 LINE COLLAPSE C406
160 LINE COLLAPSE C406 0UF39(20"),0UF33(16") 250V SCAN COUPLING CAP
160 LINE COLLAPSE C406(0U39UF/0U33F 250V)
160 LOSS OF LINE LOCK WHEN HOT. C113(2,700PF)
160 LOSS SYNC C113(2700PF)
160 NO COLOR TDA3565 +ADJ PRESET
160 NO FIELD R411
160 NO FIELD. DRYS IC301
160 NO LINE DRIVE Q503+R508(12K)
160 NO PIC C901
160 NO PIC R007(3K9)
160 NO PIC/SND R508(12K) C122
160 NO RESULTS - WHISTLE/PURR FROM PSU. R508(12K) LEFT OF AERIAL SOCKET
160 NO SND/SYNC C122(100NF)
160 NO SOUND / SYNC C122 - 100PF
160 NO SYNC - SOUND MUTED. C122(100NF) LEAKEY
160 NO VIS C901
160 NOISE THROUGH SPEAKER WHEN SET IS IN STANDBY. REMOVE C826,FIT 100NF CON IN SERIES WITH A 330R IN C826 POSITION
160 SLIGHT GHOSTING Z101 SAWF
160 STBY. R508(12K) R509(12K)R507
160 STBY. R508(12K),R509(12K)
160 STUCK IN STANDBY. R508(12K),R509(12K)
160 TASHIKO 16E891
160 TEXT LINES ACROSS TOP OF SCREEN D/J AROUND FIELD OUTPUT IC
160 TRIPPING - RAPID. 12K R507 & R508 RESISTORS FEEDING 12V STAB
160 TRIPPING. D812(BY396)
160 TRIPS D812(BY396)
160 TRIPS. D812(BY396)
160/165 CONE SHAPED RASTER. LOTPX
160/165 DEAD - FUSE BLOWN. CHOPPER(R4051),D812(BY396),R802(3.3R 4W)
160/165 DEAD FUSE CHOPTR(R4051),D812(BY396),R802(3R3 4W)
160/165 FIELD COLLAPSE IC301
160/165 NO FIELD. DRYS ON IC301
160/165 STBY. R508(12K)R509(12K)
160/165 STUCK IN STANDBY. R508(12K),R509(12K)
161
161 GEC C1410
161 DEAD - HT SUPPLY 400V Q501 ZTX651 12V REG,D503 12V ZENER
161 DEAD LL01
161 DEAD Q501 ZTX651 12V REG,D503 12V ZENER
161 DEAD Q501(ZTX651)+ D503(12V ZD)
161 FAST TRIPS 12K R507+R508
161 GEC C1410
161 NO SND LL01 CHOKE
161 NO SOUND OR LED DISPLAY LL01 CHOKE DRY JOINT
161 TRIPPING - RAPID. 12K R507 & R508 RESISTORS FEEDING 12V STAB
161 TRIPPING. R508(12K)
161 TRIPS R507 R508(12K)
161 TRIPS. R508(12K)
162
162 FIELD COLLAPSE R434 10R SAFETY RES NO OTHER FF
162 FIELD COLLAPSE R434(10R)
165 GEC C2000
165 STBY. R508(12K),R509(12K)
165 BLANK RASTER FLYBACK LINES R410(10R)
165 BLANK RASTER R410(10R)
165 BLANK RASTER WITH FLYBACK LINES - SOUND OK. R410(10R)
165 CHAN STORE INOPERATIVE ADD 10UF35V CAP ACROSS RR34 5K6
165 CHASS JUST SNOW M491BB1
165 COLD BOTTOM CRAMP IC TDA4503
165 CONE SHAPED RASTER. LOPTX
165 CONE SHAPED RASTER. LOTPX
165 DARK BAND 1-2" ACROSS CENTRE OF SCREEN. C303(220NF)
165 DARK BAND ACROSS. C303(220NF)
165 DARK BAND HORIZ. C303(220NF)
165 DEAD - FUSE BLOWN. CHOPPER TX(R4051),D812(BY396),R802(3.3R 4W)
165 DEAD CHOPTR(R4051),D812(BY396),R802(3R3)
165 DEAD FUSE CHOPTX(R4051),D812(BY396),R802(3R3)
165 DEAD L802
165 DEAD R803 R809 82K
165 DEAD R803 R809(82K)
165 DEAD. L802
165 FIELD COLLAPSE DRYS IC301
165 FIELD COLLAPSE IC301
165 FIELD CRAMP AT BOTTOM UNTIL SET IS WARM. IC TDA4503
165 FIELD CRAMP TDA4503
165 GEC C2000
165 INT CUTTING OUT Q801
165 INT CUTTING OUT. DRYS ON Q801
165 LO GAIN R102(4K7)
165 LOW GAIN R102(4K7) BAIS TO BASE Q101 SWAF TRANSISTOR
165 NO CHAN STORE ADD 4U7F35V ACROSS RR34(5K6)
165 NO LINE DRIVE R507+R508(12K)
165 NO SIGNALS TDA4503
165 NO SIGNALS TDA4503 IN IF
165 NO SND TDA4503
165 NO SOUND TDA4503 CHIP
165 NO STORE,ADD(10UF50V ACROSS RR34(5K6)
165 NO SYNC - SOUND MUTED. C122(100NF) LEAKEY
165 NO SYNC C122(100NF)
165 NO SYNC SND MUTED C122(100NF)
165 NOISE THROUGH SPEAKER WHEN SET IS IN STANDBY. REMOVE C826,FIT 100NF CON IN SERIES WITH A 330R IN C826 POSITION
165 PEAK WHITE RASTER TDA3565 I501
165 POOR PIC R102(4K7)
165 POSITION 1 KEEPS LOOSING MEMORY FIT(10UF) 35V CAP ACROSS 34(5K6)
165 POSITION 1 KEEPS LOOSING MEMORY FIT(10UF35V) ACROSS 34(5K6)
165 POSITION 1 LOOSING MEMORY FIT(10UF35V)ACROSS R34(5K6)
165 SET STUCK IN STBY QR06(BF391) FOR R007 & RO11 BOTH(3K9) IF BOTH MICROCONTROLLER
165 SIGNALS LOW GAIN R102 4K7
165 SIGNALS SNOWY R102(4K7)
165 SND MUTED - NO SYNC. C122(100NF)
165 SNOWY PIC R102(4K7)
165 SOUND MUTED - NO SYNC. C122(100NF) LEAKEY
165 SPEAKER NOISE IN STBY C826,ADD 100NF IN WITH 330R IN C826 POSITION
165 STBY MAINS SW AUX R803 R809(82K)
165 STBY MAINS SW TEMP CONTACTS R803/R809(82K)
165 STBY ONLY MAINS SW TEMP CONTACTS ONLY 0.5V(-15V) - R803/809 82K HI RES
165 STBY ONLY QR06 BF391,MICRO FAULTY(DUE TO INCREASED SUPPLY),R007 & R011 3K9
165 STBY QR06(BF391) FOR R007 RO11(3K9),MICROCONTROLLER
165 STBY QR06(BF391) MICRO,R007 R011(3K9)
165 STBY QR06(BF391) R007+RO11(3K9) MICROPRO
165 STBY. R508(12K)R509(12K)
165 STBY.R508(12K),R509(12K)
165 STUCK IN STANDBY. R508(12K),R509(12K)
165 TRIPPING HT CONSTANT AT 117V NO LINE DRIVE AS 11.5V SUPPLY MISSING PINS 7 & 22 IC101 - R507 & R508 12K
165 TRIPPING. D812(BY396)
165 TRIPS D812
165 TRIPS R507 R508(12K) D812(BY396)
165 WHITE RASTER TDA3565 I501
166
170 PROLINE 360TT TATUNG TUV9731/4
170 AFTER ELECTRICAL STORM IR02(PCD8572),AND I001(SAB3035)
170 S2000AF BY228 EW D404,Q303/R433(1R2)BD239C(TIP31);
170 BLOWING Q403 S2000AF. C421(VALUE DEPENDS ON CRT SIZE
170 CHANNEL STUCK,FRONT PANEL MEMBRANE,OR IC702(CITAC)
170 COLD NO TUNING 4MHZ XTAL X001
170 DEAD AFT STORM IR02 PCD8572 & I001 SAB3035
170 DEAD CHOPTR Q801 S2000AF . C807 100UF,C812 100UF. NOTE:- IF RUN ON REDUCED MAINS(120VAC) SET WILL TRIP EVEN THO NOT FAULTY
170 DEAD CHOPTR Q801 S2000AF.C807(100UF),C812)100UF)
170 DEAD CHOPTR(S2000AF)C807(100UF),C812(100UF)
170 DEAD IR02 PCD8572 I001 SAB3035
170 DEAD LOPTR D404 BY228,Q303+R433(1R2)
170 DEAD Q403 S2000AF. C421
170 DEAD,CHAN IND LIGHTS,CAN BE SWITCHED TO S LINE DRIVER STAGE ESP. R426 AND R427 BOTH 1K R
170 DEAD,IR02 PCD8572+I001 SAB3035
170 EW D404,Q303/R433(1R2)BD239C(TIP31);
170 FIELD COLLAPSE TDA3651 C306(100UF50V)
170 FIELD COLLAPSE TDA3651/TDA3653B,C306(100UF 50V)
170 GREEN CAST R212(47K)
170 GREEN CAST. R212(47K)
170 GREEN TINT TO PICTURE. R212(47K) HIGH
170 HI/NO BRILL D811 BA157
170 INT BLUE C531(1UF50V)
170 INT FIELD COLLAPSE - DESTROYS TDA3651. C306(100UF50V)
170 INT SYNC BRIGHTNESS DRYS ON TEXT PANEL OR POOR CONNECTIONS ON CHASSIS RIVETS + EARTHS
170 INT SYNC/BRILL/SOUND/TUNING ETC SOLDERED RIVETS CONNECTING OUTER CHASSIS TO MAIN PCB DRY JOINTED
170 IR02(PCD8572),AND I001(SAB3035)
170 LOSS OF COL & LINES BAD JOINTS EDGE CONN TXT PANEL
170 LOSS OF COL+LINES BAD JOINTS EDGE CONN TXT PANEL
170 LOW MOTORBOATING NOISE. C711(100MF 63V) TAKES OUR R802 3.3R 4WATT SURGE LIMITER L/H SIDE OF PSU
170 MOTORBOATING C711(100MF 63V)
170 NO SND BRIGHT BAND AT TOP. D811(BA157),R820(0.22R)
170 NO SND D811(BA157),R820(0R22)
170 NO SND/PIC - CHAN DISPLAY HT OK,PLUG PINS BASE OF VERTICAL SCART PANEL & ON RA16 ON SEPARATE AUDIO PANEL
170 NO SND/PIC D811(BA157)
170 NO SND/PIC PINS 115 OF M152
170 NO SOUND OR RASTER - DISPLAY OK - NO 12V RAIL DRYS ON PINS 1&15 OF M152 CONNECTOR(AUDIO/SCART PCB) MUST REMOVE
170 NO SOUND/LED & BRIGHT RASTER FADING AWAY 6V SUPPLY ONLY 2.2V - D811 BA157
170 NO START R426 R427
170 NO START R426 R427(1K)
170 NO START UP - CHAN IND OK R426/427 1K HI RES
170 NO TUNING 4MHZ CRYSTAL X001
170 NO TUNING FROM COLD,OK WHEN WARM 4MHZ CRYSTAL X001
170 NO TUNING WHEN COLD 33V OK AT PIN 17 SAB3035 BUT NO O/P PIN 15 - X001 4MHZ XTAL FAULTY
170 ONLY POSSIBLE TO SELECT ONE CHANNEL. FRONT PANEL MEMBRANE,OR IC702(CITAC)
170 PALE PICTURE - LACK OF CONTRAST - CONTROL U/S L506
170 POOR CONTRAST CONTROL L506
170 POOR CONTRAST L506
170 PROLINE 360TT TATUNG TUV9731/4
170 Q403 S2000AF. C421
170 SND THROBBING C711(100MF63V)R802(3R3)
170 SOUND - NONE LED 1/2 INCH BRIGHT BAND AT TOP. D811(BA157) HIGH FORWARD RESISTANCE,R820(0.22R)
170 STBY,R426 AND R427 BOTH 1K
170 SWITCHING ON FROM STANDBY. IC702 OR FRONT PANEL CONTROL MEMBRANE
170 SWITCHING ON FROM STBY. IC702 OR FRONT PANEL CONTROL MEMBRANE
170/180 DEAD LOPTR D404(BY228) Q303(TIP31) R433(1R2)
170/180 DIST COL - YELLOW FACES - INT C531 1UF50V IN APC LOOP
170/180 LINE O/P TR ALSO D404 BY228 E-W MOD DIODE,Q303(TIP31 OK) & R433 1R2 SAFETY RES
170/180 LOPTX=HR6237
170/180 ODD COLOR C531(1UF50V)
170/80 INT YELLOW FACES AFTER 2HRS C531 1UF50V DECODER
171
171 LINE COLLAPSE,LIN COIL
171 LINE COLLAPSE. DRYS ON LIN COIL
171 LINE COLLAPSE.LINE LIN COIL
171 NO SOUND. DRYS ON SOUND IC
171 NO TUNING - WILL SWEEP. R004(4.7R) SIDE OF TUNER
171 NO TUNING R004(4R7)
171 NO TUNING R004(4R7) BESIDE TUNER
180
180 PROLINE NV2400/NV2700 TATUNG TYS9824
180 S2000AF BY228 EW D404,Q303/R433(1R2)BD239C(TIP31);
180 BLOWING Q403 S2000AF. C421(VALUE DEPENDS ON CRT SIZE
180 BRIGHTER AT RH SIDE OF SCREEN C426 & C508 0UF1
180 BRIGHTER ONE SIDE C426 C508(0.1UF)
180 CHAN DISPLAY ONLY - NO 18V TO REG BAD JOINTS PIN 15 SCART CONN
180 CHAN DISPLAY ONLY HT AT LOP TR - NO 18V PIN 15 AV PLUG(M00-1) 26V OK AT PIN 1 CAUSED BY BURNT SKT PIN 15 - HARD WIRED
180 CHANNEL STUCK FRONT PANEL MEMBRANE,OR IC702(CITAC)
180 DEAD - CHOPPER TR 120 & 150K FEEDBACK RS & 220R RES NEXT TO CHOPPER TR
180 DEAD C807(100UF25V)
180 DEAD CHOPTR 120+150K +220R
180 DEAD LOPTR D404 BY228,Q303+R433(1R2)
180 DEAD Q403 S2000AF. C421
180 DEAD S2000AF LOPTR Q403 C433(6.8NF2KV)
180 DEAD S2000AFLOPTR Q403 C433(6N8F2KV)
180 DEAD TRIPS C806 C807(100UF25V) C805(100UF385V)TDA4600
180 EW D404,Q303/R433(1R2)BD239C(TIP31);
180 FIELD COLLAPSE TDA3651 C306(100UF50V)
180 FIELD COLLAPSE TDA3651/TDA3653B. C306(100UF 50V)
180 GREEN CAST R212(47K)
180 GREEN TINT TO PICTURE. R212(47K) HIGH
180 INSTANTLY BLOWS S2000AF LOP TR Q403 C433 6.8NF 2KV IN E-W CCT
180 INT BLUE C531(1UF50V)
180 INT FIELD COLLAPSE - DESTROYS TDA3651. C306(100UF50V)
180 LO CONTRAST 120K UNDER LOPT
180 LOW CONTRAST 120K RES UNDER LOPT
180 NO SND OR PIC LED LIT IC1001 SAB3035
180 NO SND TDA1524A VOL/TONE CONTROL
180 NO SND TDA1524A VOL/TONE CONTROL CHIP
180 NO SND/PIC IC1001 SAB3035
180 NO SND/PIC P 115 OF M152 CONNECTOR
180 NO SOUND OR PIC LED LIT IC1001 SAB3035
180 NO SOUND OR RASTER - DISPLAY OK - NO 12V RAIL DRYS ON PINS 1&15 OF M152 CONNECTOR(AUDIO/SCART PCB) MUST REMOVE
180 NO SYNC MAB8441P-T049 TXT
180 NO SYNC MAB8441P-T049 TXT CHIP
180 ONLY POSSIBLE TO SELECT ONE CHANNEL. FRONT PANEL MEMBRANE,OR IC702(CITAC)
180 PALE PICTURE - LACK OF CONTRAST - CONTROL U/S L506
180 PIC DARK LHS C426 C508(0U1F)
180 PIC DARK LHS C508(0U1F)
180 POOR CONTRAST 120K UNDER LOPT
180 POOR CONTRAST CONTROL L506
180 POOR CONTRAST L506
180 POOR PIC + INT NO PIC DRY ON AV / RGB PCB CONNECTOR M152
180 POOR/NO PIC AV/RGB PCB CONNECTOR M152
180 PROLINE NV2400/NV2700 TATUNG TYS9824
180 PULSING POWER C806/807 100UF25V+C805 100UF385V
180 PUMPING PSU AT SWITCH ON OK OFF LOAD - C806/807 100UF25V & MAINS SMOOTHER C805 100UF385V
180 Q403 S2000AF. C421
180 SOUND VIRTUALLY NON-EXISTANT TDA1524A VOL/TONE CONTROL CHIP
180 SWITCHING ON FROM STANDBY. IC702 OR FRONT PANEL CONTROL MEMBRANE
180 THIS SET'S PICTURE WAS BRIGHTER AT THE RIGHT-HAND C508(0.1UF) TDA3562A COLORDECODER CHIP
180 WATERY PIC INT OR LOSS OF SOUND/VIS DRY JOINTS PIN 15 CONNECTOR M152 ON DAUGHTER BOARD
180 WON'T START C807 100UF25V CHOPPER BASE COUPLER FROM TDA4600
185
185 NO PIC/SND 33V R005/6(10K)
185 NO SIGNALS,SLOW CHAN ETC NO 33V AT ZTK33 33V STAB - R005/6 10K 磕 RES
185 NO TUNING - DISPLAY SHOWS CORRECT CH NUMBERS. R005/6(10K,.5W)
185 NO TUNING DISPLAY R005/6(10K,.5W)
185 NO TUNING R005/6(10K,.5W)
185 OVER BRIGHT P100 & NO TUNING SIGNALS. R005/6(10K,.5W)
185 SNOW ON SCREEN R005 R006 OC 1OK
185 SNOW R005 R006(1OK)
185 SNOW,SLOW CHAN CHANGE ZTK33 R005 R006(10K)
190
190 1 OR MORE CONTROL LEVELS AT ZERO OR MAXIMUM. FRONT PB MEMBRANE
190 ALTERNATE LIGHT & DARK VERTICAL BARS. C901(10NF,2KV) DRY JOINT
190 BLANK RASTER IC702
190 BLOWING S2000AF. C404 FLYBACK TUNING CON
190 BRITNESS TURNING UP OR DOWN ON ITS OWN. HAND SET
190 CHOPPER TRANSISTOR ALSO R811 470K
190 CHOPTR+R811(470K)
190 COLOR CAST 47K VID OUTPUT
190 COLORDROP OUT. ADJ OSC CONTROL TO ABOUT 8 O'CLOCK
190 COLORTURNING UP OR DOWN ON ITS OWN. HAND SET - NO CONTROLS ON IT FOR COLOUR
190 CONTROLS WILL TURN DOWN BUT WILL NOT TURN UP. FRONT PB MEMBRANE
190 CONTROLS WILL TURN UP BUT WILL NOT TURN DOWN. FRONT PB MEMBRANE
190 DARK VERTICAL BARS C901(10NF,2KV)
190 DEAD - BLOWING TR801. R811(470K),TR801 INSULATOR
190 DEAD - FUSE BLOWN. BRIDGE RECYS,TR801,R801(3.3R),R811(470K),IC801
190 DEAD - FUSE OK. R802/3 TO 16K .6W METAL FILM
190 DEAD - NO DISPLAY. R802(15K) BY SET HT CONTROL
190 DEAD BRIDGE RECT,TR801,R801(3R3),R811(470K),IC801
190 DEAD C814(47UF250V)+C808(100UF385V)
190 DEAD CHOPTX
190 DEAD FUSE. BRIDGE RECT,TR801,R801(3R3),R811(470K),IC801
190 DEAD HT AT LOP TR - NO 10 OR 17V O/P FROM CHOPPER TFMR. DRY JOINTS CHOPPER TFMR
190 DEAD PSU TRIPPING STBY LED NOT ALIGHT C814(47UF) 250V & C808(100UF) 385V
190 DEAD PULSING HT C814(47UF250V) C808(100UF385V)
190 DEAD R802 R803(15K)
190 DEAD R803(15K)
190 DEAD R803/3 15K 磕 IN PSU
190 DEAD S2000AF CAUSE C404 R811(470K)
190 DEAD S2000AF TR403 OR D401
190 DEAD TR801,C803,IC801,R827(47) MARKED LK820
190 DEAD TR801. R811(470K)
190 DEAD TR801. R811(470K),TR801 INSULATOR
190 DEAD WITH TRIPPING C814 47UF250V,MAINS SMOOTHER C808 100UF385V
190 DEAD. R802/3(15K,0.5W)
190 DEAD. TR801,FUSE MAY SOFT BLOWN,C803 LOW,IC801,R827(47) MARKED LK820
190 DECIMAL POINT PERMANENTLY DISPLAYED/FLASHING. FRONT PB MEMBRANE,IC804 78M05CV REG
190 DISPLAY DISAPPEARS AFTER A FEW SECONDS. IC702
190 DISPLAYING '0' & REFUSING COMMANDS. FRONT PB MEMBRANE
190 DISPLAYING '0' REFUSING COMMANDS. FRONT PB MEMBRANE
190 DIST SOUND/PIC WITH BUZZ/PULLING ADJ OF L102 "TANK" COIL
190 DISTORT SND/PIC PULLING,ADJ OF L102 "TANK" COIL
190 DRIFTING OFF TUNE. FRONT PB MEMBRANE
190 DRONING NOISE. C707(470NF)
190 EXCESS BRILL R201(8R2)
190 EXCESS BRILL,OFF LR201(8R2)
190 EXCESS BRILL. R201(8.2R)
190 EXCESSIVE HEIGHT. IC TDA4505 IC803 LM31
190 FIELD COLLAPSE. R411 IC301 TDA3653B
190 FIELD TOP FOLDOVER. C409(1000UF35V) IC301
190 FOLDOVER WITH EXCESSIVE HEIGHT. IC TDA4505 NOTE IF RUNING HOT P7 FOR 12V IF HIGH IC803 LM31
190 FOLDOVER/HI HEIGHT.TDA4505,IC803 LM31
190 FRONT PANEL CONTROLS ODD,IC702 MICRO HD401220A02S PT NO 19-8315-6
190 GRAINY PICTURE. FOR 12V AT P2 OF TUNER IF NOT EDGE OF PCB
190 GREY SCALE FAULTS 47K RESISTORS(3 ON EACH OUTPUT STAGE)
190 HANOVER BARS. ADJ L502 DL501
190 HANOVER BARS. TRY ADJ L502 IF NOT DL501
190 HUM NOISE. C707(470NF)
190 INCORRECT OPERATION OF FRONT PANEL CONTROLS IC702 MICRO HD401220A02S PT NO 19-8315-6
190 INT FUNCTIONS MEMBRANE - PT NO'S IN TV MAG
190 INT SND HD401220 MICRO PT NO 1983156
190 INT STBY. REMOVE TOUCHPAD FROM SOCKET
190 LACK OF WIDTH. R413(18R)
190 LIGHT+DARK VERTICAL BARS. C901(10NF,2KV)
190 LINE FOLDOVER IN CENTRE OF SCREEN. R413(18R)
190 LINE FOLDOVER IN CENTRE OFSCREEN. R413(18R)
190 LINE FOLDOVER/CRAMP,R413(18R)
190 LINE FREQ WRONG R109 30K HI RES
190 LINE FREQ WRONG R109(30K)
190 LINE SPEED R109(30K)
190 LO HEIGHT. R411
190 LO WIDTH. R413(18R)
190 MAINS FUSE OR SURGE LIMITER R812 33K IN SNUBBER NETWORK POSITIONING - IF TOO CLOSE TO HEATSINK WILL FLASH OVER
190 NO COLOR- OR LOSS OF ONE COLOUR. BREAK IN PCB BY DELAY LINE,IC501 TDA3565
190 NO COLOR DELAY LINE,IC501 TDA3565
190 NO FIELD. R411 IC301 TDA3653B
190 NO LINE DRIVE C111(2N7)
190 NO LINE DRIVE TDA4505 IC101,C111(2N7)
190 NO PIC - SOUND OK NO LINE DRIVE PIN 26 TDA4505 IC101,C111 2N7 TIMING CAP
190 NO PIC - SOUND OK R413 18R METAL FILM RES IN LINE DR SUPPLY
190 NO PIC C111
190 NO PIC NO EHT NO LINE DRIVE C111 OC LINE OSC TUNING
190 NO PIC R413(18R)
190 NO PIC SND OK R413(18R)
190 NO RASTER - SOUND OK - NO HEATERS. DRYS ON LOPTX
190 NO REMOTE OPERATION. 5 VOLT REG
190 NO REMOTE OPERATION. 5 VOLT REGULATOR
190 NO REMOTE OPERATION. 5 VOLT REGULATOR LOW O/P
190 NO SND ON CHAN CHANGE HD401220 MICRO PT NO 1983156
190 NO SOUND/RASTER WITH "0" DISPLAYED REMOVE SWITCH MEMBRANE TO OPERATION OF TV - IF OK THEN MEMBRANE U/S
190 NO SYNC. R109(30K),R111(4.7K POT),C111(2N7),TDA4505
190 NO SYNC. R109(30K),R111(4K7 HOLD CONTROL),C111(2N7),TDA4505
190 NO TUNING. R769(33K),R005(5.6M),TOUCH-PAD MEMBRANE,TAA550 33V REG,LAST TUNER
190 NO TUNING. R769(33K),R005(5M6),TAA550 33V REG
190 NO TUNING. R769(33K),R005(5M6),TOUCH-PAD MEMBRANE,TAA550,TUNER
190 NOISY PICTURE. TUNER MAY NOT SHOW UP BY BANGING IT
190 ODD CONTROLS MEMBRANE/IC702 MICRO HD401220A02S PT NO 19-8315-6
190 ODD NOISE. C707(470NF)
190 OFF TUNE ADJUST VIS DET COIL L102
190 PART BAND TUNING. TOUCH-PAD MEMBRANE,TAA550 33V REG,TUNER
190 PATTERNING OVER BOTTOM HALF OF PICTURE. FIELD IC
190 PIC/SOUND GOES OUT OF TUNE & PULSES AFTER CHAN ADJUST VIS DET COIL L102(TANK)
190 POOR 47K ON CRT BASE
190 POOR OR DRIFTING GREY SCALE. 1 OR MORE OF THE RGB LOAD RESISTORS 47K ON CRT BASE
190 POOR OR NO SYNC. R109(30K),R111(4.7K HOLD CONTROL),C111(2.7N),TDA4505
190 PSU SHUTING DOWN WITH BLEEPING SOUND. S2000AF TR403 OR D401
190 RAGGED VERTICALS C112
190 RAGGED VERTICALS R413(18R)
190 RAGGED VERTICALS. R413(18R)
190 RAGGED VERTICALS. R413(18R),C112
190 RASTER BUT NO DISPLAY. IC702
190 REDUCED HEIGHT. R411 HIGH
190 REVERTS TO STBY AFT 10 SECS WITH WHISTLING 115V HT RISES TO 150V IN STBY - R827 47R 4W IN PSU PRI
190 RIPPLED VERTICALS. C112 DRY JOINTED
190 S2000AF. C404
190 SLOW START R803(16K)
190 SLOW START UP R803 16K START UP RES(READ OK OUT OF CCT)
190 SLOW START,R803(16K)
190 SND LOW WHEN CHANGING CHANNEL. SW OFF,HOLD MEM BUTTON SW ON,PRESS VOLUME +,SW OFFON AGAIN
190 SND ON CHANNEL,SW OF,HOLD MEM BUTTON+SW ON,PRESS VOL+,SW OFF
190 SND TURNING UP OR DOWN ON ITS OWN. HAND SET FAULTY
190 SNOWY PICTURE. TUNER
190 SOUND GOING LOW WHEN CHANGING CHANNEL. SW OFF,HOLD MEM BUTTON & SW ON,PRESS VOLUME +,SW OFF & ON AGAIN
190 SOUND LOST ON CHAN HD401220 MICRO PT NO 1983156
190 SOUND TURNING UP OR DOWN ON ITS OWN. HAND SET
190 STBY R827(47R)
190 STBY. REMOVE TOUCHPAD FROM SOCKET
190 STUCK IN TEST MODE. FRONT PB MEMBRANE
190 STUCK ON 1 CHANNEL - OK VIA REMOTE. PRINT CRACKED BY R717-723
190 STUCK ON 1 CHANNEL R717-R723 FRONT PB MEMBRANE IC702
190 STUCK ON 1 CHANNEL. FRONT PB MEMBRANE
190 STUCK ON 1 CHANNEL. R717-723(270K OR 180K),OR IC702
190 STUCK ON 1 CHANNEL. R717 R723(270K OR 180K),OR IC702
190 SWITCHING TO STANDBY. REMOVE TOUCHPAD FROM SOCKET
190 TEST MODE. FRONT PB MEMBRANE
190 TOP FOLDOVER. C409(1,000U F,35V) OR PRINT AROUND IC301
190 TOP FOLDOVER. C409(1,000UF,35V) IC301
190 TRIPPING BRIGHT SCRN. 1ST ANODE/FOCUS VOLTAGE MODULE/PCB PINS
190 TRIPPING LOPTX
190 TRIPPING LOPTX R411 IC301 TDA3653B
190 TRIPPING OR HT LOW(115VN OR 109VN) MAY START UP CORRECTLY IF SCAN COILS UNPLUGGED . C803 220UF16V(PSU IC SUPPLY)
190 TRIPPING WITH PEAK-WHITE RASTER. DRY ON TAG AT BOTTOM OF 1ST ANODE/FOCUS VOLTAGE MODULE/PCB
190 TRIPPING WITH SCAN PLUG & CRT BASE REMOVE. LOPTX
190 TRIPPING,IC101
190 TRIPPING,R411 TDA3653B
190 TRIPPING. R411 FEED TO IC301 TDA3653B
190 TRIPPING. TRACK TO PIN 23 OF IC101
190 TRIPS C803(220UF16V)
190 TUNER DRIFT,AFC DET COIL L102(TANK)
190 TUNING DRIFT KEYBOARD MEMBRANE HAD RECENTLY BEEN FITTED. R005 5R6 NEVER FITTED
190 TUNING DRIFT R005(5R6)
190 TUNING DRIFT. TOUCH-PAD MEMBRANE,TAA550 33V REG,LAST TUNER
190 TUNING DRIFT. TOUCH-PAD MEMBRANE,TAA550 33V REG,TUNER
190 TUNING SWEEP SLOW,5 VOLT REGULATOR
190 TUNING SWEEP VERY SLOW. 5 VOLT REGULATOR
190 TUNING SWEEP VERY SLOW. 5V REGULATOR
190 UNCONTROLLABLE BRIGHTNESS. R201(8.2R) FEED TO RGB O/P
190 WHITE RASTER WITH FB LINES THEN PARTIAL FIELD COLL AFTER WHICH SWITCHED OFF R201 8R2 1/2W IN RGB FEED
190 WILL NOT TUNE WHOLE BAND. TOUCH-PAD MEMBRANE,TAA550 33V REG,LAST TUNER
195
195 COLD RETUNE IC001(TAA550)
195 JUST SNOW,LO 33V R009/R010(6K8) IC001(TAA550) LOC=142
20TKG SERVICE MODE ?
28BKD D28N440
28BKD D28N440 GOTO PRO4400
30 BRADFORD
30 BRADFORD
30 BRIGHTNESS - VARIATIONS INT. CLEAN PRESET BRIGHTNESS CONTROL
30 BRIGHTNESS CHANGES PRESET BRIGHTNESS CONTROL
30 BRIGHTNESS VARYSS INT. CLEAN PRESET BRIGHTNESS POT
30 CONTRAST - VARYING ESP BETWEEN STATIONS. C60(22U F)
30 CONTRAST CHANGES C60(22UF)
30 CONTRAST VARYING DIFF STATIONS C60(22UF)
30 GREEN PIC IC MC1327P
30 GREEN PIC MC1327P
30 GREEN PICTURE. IC MC1327P
30 LIGHT & DARK VERTICAL BANDS(STRIATIONS) PL509,P7500,C423
30 LINE FREQ R430(39K)
30 LINE FREQ. R430(39K)
30 LINE SLOW TO SETTLE AFTER ADJ LINE FREQ. R430(39K) HIGH
30 STRIATIONS PL509,P7500,C423
30 VERTICAL STRIATIONS PL509,P7500,C423
70
70 BRIGHTNESS REDUCED. R910(180K,1W),VR908(2M2)
70 DEAD - BLOWING CHOPPER TRANSISTOR(INT) R637(2K2,7W),DRY JOINT ON TR604(8SR56)
70 DEAD - BLOWN FUSE & CHOPPER. D608,D610,C627(10UF,16V)
70 DEAD - BLOWN FUSE 1A F601. DARLINGTON BUW,D608/610,TR601/2/3/4,IC601,C627,D603/4
70 DEAD C624(100UF)
70 DEAD CHOPTR D608,D610,C627(10UF,16V)
70 DEAD CHOPTR R637(2K2,7W),TR604(8SR56)
70 DEAD CHOPTRR637(2K2) TR604(8SR56) D608,D610,C627(10UF16V)
70 DEAD DARLINGTON BUW,D608/D610,TR601/2/3/4,IC601,C627,D603/4
70 DEAD FUSE D608/610,TR601 TR602 TR603 TR604,IC601,C627,D603 D604
70 DEAD. C624(100U F)
70 INT START R625(180K)
70 LO BRIGHTNESS R910(180K)VR908(2M2)
70 LO BRILL,R910(180K),VR908(2M2)
70 NO PIC EHT OK YEL LEAD ON BACK OF MOTHER BOARD BY DECODER OFF
70 NO PICTURE - E.H.T.PRESENT YELLOW LEAD ON BACK OF MOTHER BOARD BY DECODER OFF
70 PIC ROLLS C308(10UF)
70 POOR FIELD SYNC POOR. C308(10UF)
70 POOR START R625(180K)
70 STARTUP - INT. R625(180K)
70 SYNC - FIELD SYNC POOR. C308(10UF)
70 TRIPPING - FUSES OK. C633(680PF)
70 TRIPPING - INTLY. C617(6 8NF) FOR LEAK
70 TRIPPING C617(6N8F)
70 TRIPPING. C633(1000PF)
70 TRIPPING. D602(ZPD22),R636,C633(680PF),IC61
70 TRIPPING. TRIP,C633 FIT 1,000PF INSTEAD,DRYS ON CHOPPER TRANSISTOR
70 TRIPS C633(680PF) C617(68NF)D602(ZPD22),R636,C633(680PF),IC61
70 VERT RED STRIPES. C208(22NF)
70 VERTICAL RED STRIPES. C208(22NF)
80
80 GRANADA C20SD1 / C20TD1
80 CHANNEL - NO CHANNEL . TR713,D300
80 CHANNELS - WILL NOT FROM C4 TO BBC1. C3(0.1F)
80 CHANNELS STICKING C3(0.1F)
80 DEAD - BLOWING MAINS FUSE FOR NO REASON. FUSE HOLDER FOR BEING LOOSE OR CHARRED
80 DEAD D302(IN4148),D600-3,RBA920,LOPTX,TRIPLER
80 DEAD. D302(IN4148),D600-3,RBA920,LOPTX,TRIPLER
80 GRANADA C20SD1 / C20TD1
80 INT FIELD COLLAPSE. FIELD IC,VERTICAL HOLD CONTROL
80 LINE COLLAPSE L401,C403
80 LINE COLLAPSE,L401,LIN LIN+WIDTH COILS,C403
80 LINE COLLAPSE. DRY JOINT ON L401,LIN LIN & WIDTH COILS,C403
80 LINE SYNC. IC TDA920 SYNC/LINE OSC
80 NO CHANNEL CHANGE. TR713,D300 C3(0.1F)
80 NO SYNC TCA270 TDA920
80 SYNC - LOSS OF LINE SYNC. IC TCA270 DEMODULATOR IC ON IF PANEL
80 SYNC - LOSS OF LINE SYNC. IC TDA920 SYNC/LINE OSC IC
80 TELETEXT - INTERFERENCE. 4 PAGE LAY OUT
89 01 TRIPPING HI HT(115VN/109VN) C803(220UF16V)
8901 TRIPPING OR HT LOW(SHOULD BE 115V OR 109V)MAY START UP CORRECTLY IF SCAN COILS UNPLUGGED . C803 220UF16V(PSU IC SUPPLY) OC
90
90,LINE COLLAPSE C424(330NF250V)
9478 POOR CONTRAST R427 120K(BEAM LIMIT FROM 121V)
9478 POOR CONTRAST R427(120K)
9478 POOR LOW CONTRAST PICTURE R427 - 120K(BEAM LIMIT SUPPLY FROM 121V)
A VESTEL 11AK19 ?
A DEAD R802 R803(15K)
A DEAD R808
A DEAD/STBY LM317 12V
A SERIES
A SERIES DEAD R802 R803(15K)
A SERIES DEAD WITH SQUEAL DRY JOINTS R808 WW RESISTOR
A SERIES DEAD/SQUEAL R808
A SERIES NO REMOTE OPERATION IR RX FAULTY
A SERIES VARYING HT DRY JOINTS R808 WW RESISTOR
A STBY LIGHT GOES OUT BUT SET DOES NOT COME ON LM317 12V REG DRY JOINTS
A STBY LM317 12V REG
ALSO SEE TATUNG
ALSO SEE TATUNG
B SERIES
B DEAD D807(1N4148)
B DEAD LED FLASHING D810(BY399)
B DEAD PIN 7 IC801 LOW D807 1N4148 U/S
B DEAD WITH STBY LED FLASHING D810 BY399 - FEEDBACK CCT ASSOC WITH CHOPPER FET Q801
B DEAD/LED BLINK D810(BY399)
B ENTER SETUP,MOVE JUMPER LINK BY MICROPRO,UP/DOWN,BALANCE LEFT+RIGHT
B LINE WHISTLE ADD 220PF TWEEN PIN 5 PIN 6 OF OPTO IC802
B LINE WHISTLE MOD REQD ADD 220PF CAP TO PIN 5+PIN 6 OF OPTO IC802
B NO LINE OR FIELD SYNC - VIDEO AT PIN 5 TDA2579A TB GEN IC401 IC703 EEPROM
B NO SYNC 27MHZ XTAL ON TXT PCB
B NO SYNC TDA2579A IC401 IC703 EEPROM
B SERIES
B SERIES LINE WHISTLE - MOD REQD ADD 220PF CAP TO PIN 5 & PIN 6 OF OPTO IC802 IN PSU
B SERIES LOSES REGISTER 7(LINE OSC FREE RUN) DRY JOINTS 27MHZ XTAL ON TXT PCB
B SERIES SERVICE MODE1 MOVE JUMPER LINK BY PROC TO OTHER POSN. NO. IN LH OF SCREEN IS PARAMETER & CAN BE STEPPED THRO' IN HEX B SERIES SERVICE MODE2 FROM 00 TO 12 USING "3" BUTTON(UP) & "2" BUTTON(DOWN). PARAMETERS D BY USING "BALANCE LEFT & RIGHT"
B SERVICE MODE MOVE JUMPER LINK BY PROCESSOR TO OTHER POSN
C SERIES
C CHILD LOCK HOLD PROG + WHILST SWITCHING ON
C CHILDLOCK ON SW ON TV HOLDING IN 'P+' BUTTON ON FRONT
C CHILDLOCK ON SW ON TV WHILST HOLDING IN 'P+' BUTTON ON FRONT
C COLD MIDDLE CRAMP,R413(18R),115VN/109VN
C FIELD COLLAPSE I402
C HOT,INT TRIP TDA4605
C INT TRIP TDA4605
C LINE DOWN PIC R413(18R)C NO R/C IC750 TFMS4360N/TFMS5360
C NO FRONT PANEL,SWITCH SET OFF,PRESS HOLD P+ ON SET
C NO R/C,IC750 TFMS4360N WITH TFMS5360
C PIC CUTS OUT CE803(220UF16V)
C SERIES CHILDLOCK ON SW ON TV WHILST HOLDING IN 'P+' BUTTON ON FRONT
C SERIES CUTS OUT ON HIGH BRIGHTNESS SCENES HT VOLTS DROPS IN SYMPATHY - CE803 220UF16V(SUPPLY TO TDA4605)
C SERIES FIELD COLLAPSE DRY JOINT I402
C SERIES FOR VOLUME - PRESS --/- ON REMOTE,VOL + ON SET,--/- ON REMOTE FOR NO FRONT PANEL,PRESS & HOLD P+ ON S
C SERIES INT TRIP - ONCE OR TWICE A DAY WORSE WHEN HEATED - - TDA4605 HEAT SENSITIVE - U/S
C SERIES LINE DOWN PIC WHEN COLD(FOLDED SCAN) R413 18R 磕 HI RES - HT CORRECT -115V 14/20"; 109.5V 15/21"
C SERIES NO R/C OPERATION NO O/P FROM R/C CHIP IC750 TFMS4360N WITH TFMS5360
C SERIES STBY LED ON - OTHERWISE DEAD DRY JOINT ON END PIN SCART SKT DEPRIVING LINE FEED TO DR TFMR
C SERIES STBY ONLY HT(B+) PRESENT - ON/OFF SW PERM MADE - WAS FAULTY
C SERIES STUCK ON CHAN 1 & NO ANALOGUE CONTROL(CHILDLOCK) HOLD "PROG +" WHILST SWITCHING ON
C SERIES TATUNG DU6C22
C SERIES TATUNG TU2C52
C SERIES TATUNG VU2CEO
C SERIES VOLUME WON'T ADJ OVER FULL RANGE OR NO FRONT PANEL OP.SWITCH SET OFF
C STBY HT OK ON/OFF SW
C STBY LED ON OTHERWISE DEAD ON END PIN SCART SKT DEPRIVING LINE FEED TO DR TX
C STBY SCART SKT
C STUCK ON CHAN 1(CHILD LOCK) HOLD "PROG +" WHILST SWITCHING ON
C TATUNG DU6C22
C TATUNG TU2C52
C TATUNG VU2CEO
C TRIPS ON HI BRILL,CE803(220UF16V)
C VOLUME RANGE PRESS REMOTE(--/-)R,VOL + ON SET,REMOTE(--/-)REMOTE F,MAINS OFF,PRESS+HOLD P+ MAINS ON
C VOLUME WON'T ADJ PRESS --/- ON REMOTE,VOL + ON SET,--/- ON REMOTE
CT1273 120 CHASSIS
CT1273 SEE 120
CT9273 120 CHASSIS
CT9273 SEE 120
CV1371 130 CHASSIS
CV1371 SEE 130
CV1810 110 CHASSIS
CV1810 SEE 110
CV9371 CHOPTR BU426A+R808(150K+C814(1UF)+TDA4600
CV9371 DEAD - F802 BU426A CHOPPER ; R808 150K HI RES; C814 1UF & CHECH TDA4600
CV9371 DEAD BU426A CHOPTR,R808(150K),C814(1UF),TDA4600
CV9371 DEAD F802,BU426A R808(150K) C814(1UF) TDA4600
CZ8151 110
CZ8151 110 CHASSIS
CZ8152 110
CZ8152 110 CHASSIS
D SERIES
D AFC SPEED UP R001 TO 18K R003 TO 27K
D ALL RED. R012(100K) ON CRT BASE
D FIELD COLLAPSE R504(3M3)
D FIELD COLLAPSE R504(3M3),IC503(TDA8362)
D FILED COLLAPSE IC401 R414 R504(3M3)
D GREEN PIC - LOSS OF B DRIVE R922 100K FEEDBACK/BIAS COULD AFFECT OTHER COLS(R932/912)
D GREEN PIC R922(100K)
D GREEN PIC TR931(BC547)+R932(100K)
D GREEN RASTER TR931(BC547),R932(100K)
D LINE FOLDOVER R427
D LINE FOLDOVER,R427
D LO HEIGHT 33V IC001 TAA550+R015/6 6K8+R504(3M3)
D LO HEIGHT 33V SUPPLY IC001 TAA550 R015 R106 6K8 R504(3M3)
D LOCKED ON 1 CHAN & VOL AT MAX EEPROM,RESET FACTORY PINS 1 & 2 PC701 NEAR UF(WHILST TV IS ON) & PRESS ANY BUTTON ON TV,GO TO STBY
D NO FIELD IC401+R414+R504 3M3
D NO LINE DRIVE R427(22R)
D NO LINE DRV R427(22R)
D NO PIC SQUEAL AT SW ON R427 22R .5W IN LINE DRIVE
D NOISY POWER C806(2U2F50V)
D NOISY STBY C806 TO(2U2F50V)
D ODD COLOR PIC,R922R932 R912,100K
D ON CHAN1 VOL MAX EEPROM RESET PINS 1 2 PC701(WHILST TV IS ON) PRESS ANY TV BUTTON
D RED PIC. R012(100K) CRT BASE
D RESET EEPROM PINS 1+2 PC701(TV ON)+PRESS ANY FRONT PANEL,SWITCH OFF
D SERIES ALL RED. R012 100K ON CRT BASE
D SERIES BRIGHT GREEN RASTER GREEN CATHODE VOLTS LOW - TR931 BC547 & R932 100K HI RES
D SERIES FIELD COLLAPSE R504 3M3 - FEEDS RAMP TO PIN 42 IC503 TDA8362
D SERIES IMPROVEMENT OF AFC PULL IN TIME AND INTER-CHANNEL MUTE R001 TO 18K & R003 TO 27K
D SERIES LACK OF HEIGHT 33V SUPPLY IC001 TAA550 & FEED RES R015/6 6K8 & R504 3M3
D SERIES LINE FOLDOVER WITH CRT HEATERS DIMMING R427 LINE FEED RES HIGH RES
D SERIES NO FIELD SCAN IF IC401 & R414 ARE OK R504 3M3 R
D SERIES NO LUMINANCE(NEGATIVE PIC),CRT
D SERIES NOISY POWER SUPPLY IN STAND BY C806 TO 2.2UF50V
D SERIES TUNING PROC PRESS 'FILLED SQUARE' BUTTON,PRESS '4',SEARCH UP WITH '4',DOWN WITH '4&3'. PRESS '5' TO STORE CHAN,PRESS'6' EXIT
D TUNING PRESS [],'4','5' TO STORE CHAN,PRESS'6' TO EXIT SET UP
D TUNING PROC PRESS 'FILLED SQUARE',UP'4',DOWN'4&3'.'5'STORE,'6' TO EXIT
D10R609 LO WIDTH RH04(22R),CH09(2200UF10V)
D10R609 WIDTH RH04(22R) CH09(2200UF16V)
D14
D14FG6 TATUNG F SERIES
D14RDD5 VOLUME CHILD LOCK,PRESS VOL+ ON SET AND BUTTON ON RHS OF 0 ON REMOTE
D14RFG5 BOTTOM CRAMP TEA8172
D14RFG5 F SERIES SEE TATUNG
D14RFG5 LINES AT BOTTOM TEA8172
D14RFG5 LINES AT BOTTOM WHEN HEATED FOP IC TEA8172
D14RFG6 DEAD LED FLASHING 4 TIMES R909/R913/R922 ALL 180K ON THE CRT BASE
D14RFG6 DEAD Q404,Q801,D805,R814
D14RFG6 F SERIES
D14RFG6 F SERIES TATUNG SEE BELOW
D14RFG7 NO PIC SND/OSD OK
D14RKG5 NO SND LA602 CHOKE ON SPKR/HPHONE PCB
D14TFG5 F DEAD BRIDGE RECT,CHOPTX ETC
D14TFG5 F NO RED,R909(180K)
D14TT92 DEAD RP06(3M9)
D20RDE6 D SERIES NO LUMA( NEGATIVE PIC),CRT
D20RDE6(D SERIES)
D20TDE6 SEE TATUNG D SERIES
D20TFG5 F SERIES
D20TFG5 STBY PSU NOISE LO HT C809(100UF250V)
D21TD6 NO RED R912
D25N 440 SERVICE MODE SWITCH ON WHILST HOLDING MENU ON SET TIL RED LED PRESS R/C STBY
D25N440/25BKA TATUNG 440 TATUNG 440
D25NEE5 TATUNG E
D28N440 PRO4400
D28N440 28BKD
D28N440 GOTO PRO4400
D28N440 INT START TP6 BD441 ICP3 TDA8133
D28N440 NO PIC/SND CL18,TP6(BD441)
D28N440 STBY,TDA8133
D28NE55 FIELD 2 BLACK LINES AT TOP OF PIC R437 22R
D28NE55 FIELD COLLAPSE TDA8350
D28NE55 FIELD COLLAPSE TDA8350 CURED THIS BUT 2 BLACK LINES AT TOP OF PIC R437 22R
D28NE55 FIELD COLLAPSE TDA8350 R437(22R)
D28NE55 FIELD COLLAPSE TDA8350+R437(22R)
D28NEE5 DEAD LOPTR,RESOLDER ALL CAPS NEARBY
D28NEE5 DEAD/STBY R814(75K)
D28NEE5 E1 SLIGHT TOP FOLDOVER TDA8350Q
D28NEE5 EXCESS WIDTH R814(75K),TR801,ZD813
D28NEE5 INT DEAD R814 75K
D28NEE5 INT DEAD R814(75K)
D28NEE5 TATUNG E SERIES
D28NEE5 TATUNG E1
D28NEF6 NO PIC SND OK,SCAN COILS
D28NGH5 GSERIES
D28NT92S DEAD CRT ARCING BURNS RD17(4K7),RD06(10K)
D28NT92S DEAD RD17(4K7) RD06(10K)
D28NT92S PT92 DEAD 320VOK NO O/P TDA16846 CHOPTR(04N60S5) OPTO(LTV702FA)
D28NT92S PT92 DEAD,NO STBY LED RP06(3M9),RP05(1M) RP07(15R) IN PSU
D28NT92S(PT92)
D28W
D28W440 PRO4400
D28W440 4400 CHASSIS
D28W440 GOTO PRO4400
D28W441 PRO4400
D28W441 GOTO PRO4400
D28WT92S
D28WT92S SEE PT92
D28WT92S DEAD RP06(4M7)
D28WT92SN PT92 NARROW PIC CD21(680NF)RV38(2R2)
D28WT92SN PT92 STBY CD21,DD07(BY228) RV38(2R2)
D32W4415 DEAD LOPTX(FBT40824)
DBN9B52P B SERIES BALLOONING PIC DRY JOINTS LINE SCAN COILL PLUG ON MAIN PCB
DBS
DBS9892C DEAD RA50 RA16(3W)
DBS9892C DEAD SCART CONN(12V ROUTED THRO IT) REMOVE NICAM PCB
DBS9892C INT DEAD DRY JOINTS RA50 & RA16 3W STAND UP RES ON AUDIO O/P PANEL & JOINTS ON 12V REG ON MAIN PCB
DBS9892C INT DEAD DRY JOINTS SCART CONN(12V ROUTED THRO IT)- REMOVE NICAM PCB
DBS9892C INT NO LINE DRV,LINK POWER ACROSS SCART PCB END PINS
DBS9892C INT SW OFF R817/819 220R 磕 IN PRI PSU & C812 100MFD,C807 100MFD & C806 100MFD
DBS9892C NO STARTUP R817 & R819 IN THE PRIMARY PSU STAGE(BOTH 220R 0.5 WATT)(C812 100MFD,C807 100MFD & C806 100MFD)
DBS9892C STBY R817 R819 C812(100UF) C807(100UF)C806(100UF)
DBS9892C THUMPING NOISE ON AUDIO DRY JOINTS AUDIO PCB
DBS9892C VERTICALS RAGGED C418(470UF35V)
DBS9892C VERTICALS RAGGED WHEN COLD C418 470UF35V BETWEEN T401 & SCART PCB
DECCA 140,145,160,161=FAT30005
DN1251 120/125
DN1251 120/125 CHASSIS
DN1253 120
DN1253 120 CHASSIS
DN1256 120/125
DN1256 120/125 CHASSIS
DN1259 120/130
DN1259 120/130 CHASSIS
DN1451 140
DN1451 140 CHASSIS
DN1471 140
DN1471 140 CHASSIS
DN1651A 160
DN1651A 160 CHASSIS
DN1670 160
DN1670 160 CHASSIS
DN1671 160
DN1671 160 CHASSIS
DN1672 160
DN1672 160 CHASSIS
DN1674 160
DN1674 160 CHASSIS
DN8452 140
DN8452 140 CHASSIS
DN8472 140
DN8472 140 CHASSIS
DN8652 165
DN8652 165 CHASSIS
DN8951 190 BOOTS C1411/2 MATSUI 1424
DN8951 190 CHASSIS
DN8951 190 CHASSIS BOOTS C1411/2 MATSUI 1424
DN8951 190/195
DN8954 190
DN8955 190
DN8955 190 CHASSIS
DN9256 120/125
DN9256 120/125 CHASSIS
DN9257 120/125
DN9257 120/125 CHASSIS
DN9259 120/130
DN9259 120/130 CHASSIS
DO ALSO SEE TATUNG
DP1257 120/130
DP1257 120/130 CHASSIS
DP1453 140
DP1453 140 CHASSIS
DP1473 140
DP1473 140 CHASSIS
DP1653/A 160
DP1653/A 160 CHASSIS
DP1673 160
DP1673 160 CHASSIS
DP8454 140
DP8454 140 CHASSIS
DP8474 140
DP8474 140 CHASSIS
DP9257 120/130
DP9257 120/130 CHASSIS
DP9454 140
DP9454 140 CHASSIS
DT1253 120
DT1253 120 CHASSIS
DT1257 120/125
DT1257 120/125 CHASSIS
DT1260 120
DT1260 120 CHASSIS
DT1263 120
DT1263 120 CHASSIS
DT1455 140
DT1455 140 CHASSIS
DT1475 140
DT1475 140 CHASSIS
DT1655 160
DT1655 160 CHASSIS
DT1675 160
DT1675 160 CHASSIS
DT8456 140
DT8456 140 CHASSIS
DT8459 140
DT8459 140 CHASSIS
DT8466 145A
DT8466 145A CHASSIS
DT8476 145A
DT8476 145A CHASSIS
DT8496 145A
DT8496 145A CHASSIS
DT9253 120
DT9253 120 CHASSIS
DT9255 120/125
DT9255 120/125 CHASSIS
DT9260 120/125
DT9260 120/125 CHASSIS
DT9456 140
DT9456 140 CHASSIS
DT9459 140
DT9459 140 CHASSIS
DT9466 145A
DT9466 145A CHASSIS
DT9476 145A
DT9476 145A CHASSIS
DT9496 145A
DT9496 145A CHASSIS
DT9497 140
DT9497 140 CHASSIS
DT9770 190/195
DT9770 190/195 CHASSIS
DT9772 171 CHASSIS
DU6C22 SEE C SERIES
DU8670M 165
DU8670M 165 CHASSIS
DU8688 165
DU8688 165 CHASSIS
DUN9A52 ARCING LOPTX(DST286N243/47296102 HR7163) HT=109VN
DUN9A52 HUM BAR RESOLDER CHOPTX AREA
DUS9796C DEAD SET ON/OFF SWITCH BURNT
DUV9A52 SEE TATUNG
DV1254 120
DV1254 120 CHASSIS
DV1351 130
DV1351 130 CHASSIS
DV1353 130
DV1353 130 CHASSIS
DV1360 130
DV1360 130 CHASSIS
DV1361 130
DV1361 130 CHASSIS
DV1457 140
DV1457 140 CHASSIS
DV1462 140
DV1462 140 CHASSIS
DV1475 140
DV1475 140 CHASSIS
DV1477 140
DV1477 140 CHASSIS
DV1657 160
DV1657 160 CHASSIS
DV1677 160
DV1677 160 CHASSIS
DV8458 140
DV8458 140 CHASSIS
DV8460 140
DV8460 140 CHASSIS
DV8468 145A
DV8468 145A CHASSIS
DV8478 147
DV8478 147 CHASSIS
DV8498 145A
DV8498 145A CHASSIS
DV8554 150
DV8554 150 CHASSIS
DV9101 111
DV9101 111 CHASSIS
DV9151 111
DV9151 111 CHASSIS
DV9254 120
DV9254 120 CHASSIS
DV9351 130
DV9351 130 CHASSIS
DV9352 130
DV9352 130 CHASSIS
DV9357 131
DV9357 131 CHASSIS
DV9458 140
DV9458 140 CHASSIS
DV9460 140
DV9460 140 CHASSIS
DV9468 145A
DV9468 145A CHASSIS
DV9498 145A
DV9498 145A CHASSIS
DV9499 140
DV9499 140 CHASSIS
DV9551 150
DV9551 150 CHASSIS
DV9758 170/180
DV9758 170/180 CHASSIS
DYS9893C 180
DYS9893C 180 CHASSIS
DYS9893C= TATUNG 170/180
DYV9B51P EXCESS WIDTH EW RASTER,L408
DZ1352 130
DZ1352 130 CHASSIS
DZ1362 130
DZ1362 130 CHASSIS
DZ9152 111
DZ9152 111 CHASSIS
DZ9352 130
DZ9352 130 CHASSIS
DZ9354 130
DZ9354 130 CHASSIS
DZ9358 120/130
DZ9358 120/130 CHASSIS
DZ9362 130
DZ9362 130 CHASSIS
DZ9555 150
DZ9555 150 CHASSIS
E SERVICE MODE REMOVE SK702 LINK(LHS OF IC701)+VOL +/-,BRILL +/-
E 01 90 SYSTEM OPTIONS RESET TO D0
E 02 20 HUE NOT USED DO NOT ADJUST
E 03 0E HOR SHIFT MUST BE LESS THAN 40
E 05 36 E.W.PAR MUST BE LESS THAN 40
E 06 2D E.W. CORNER MUST BE LESS THAN 40
E 07 14 E.W. TRAPEZ MUST BE LESS THAN 40
E 08 20 VERT SLOPE MUST BE LESS THAN 40
E 0D 2A GREEN DRIVE MUST BE LESS THAN 40
E 0E AA BLUE DRIVE MUST BE BETWEEN 80&BF
E 0F 57 PEAKING RESET TO 1A
E 10 5F BRIGHTNESS MUST BE BETWEEN 40&7F
E 11 A0 SATURATION MUST BE BETWEEN 80&BF
E 12 1F CONTRAST MUST BE LESS THAN 40
E 13 03 AGC MUST BE LESS THAN 40
E STORE SETTINGS WITH SND MUTE BUTTON
E SERIES
E 0A 5C VERT S COR MUST BE RESET BETWEEN 80&BF
E 0B 1B VERT SHIFT MUST BE LESS THAN 40
E 09 16 VERT AMP MUST BE LESS THAN 40
E 0C 2A RED DRIVE MUST BE LESS THAN 40
E D28NEE5 DEAD IC804 5V REG
E D28NEE5 E/W WIDTH ZD409(33V ZD)E D28NEE5 EXCESS WIDTH/LO HEIGHT,R814 E D28NEE5 FIELD COLLAPSE R422(1R2)
E D28NEE5 FIELD FOLDOVER R437(1R2)
E D28NEE5 HI BRIGHTNESS C527(100N)
E DEAD R423 TR403(2SC1815Y)
E DEAD R423,TR403 2SC1815Y
E FIELD COLLAPSE C805(1000UF) TDA8350Q R814E LO WIDTH C822
E FIELD COLLAPSE,C805(1000UF)+TDA8350Q+R814(75K)+2R2
E FIELD PART COLLAPSE,TDA8350Q
E HIGH HT R834(75K)
E HOTEL MODE PRESS AND RELEASE A VOLUME BUTTON. WHILE OSD SHOWS,PRESS R/C MUTE
E INT VIDEO XL301,R308,IC302
E LED NO LINE DRIVE T401 TX
E LO HT R834(75K)
E LO WIDTH/HT C822
E NO LINE DRIVE DR TX T401
E NO PIC R940(4R7) R901(22R)
E NO PIC R940(4R7),R901(22R)
E NO PIC XL301,R308,IC302
E SERIES DEAD R423 IN PRI OF LINE DR - TR403 2SC1815Y
E SERIES FIELD COLLAPSE C805 1000UF 2R2(45 VOLTS TO FIELD) & TDA8350Q R814 75K 150VN
E SERIES HI HT,R814 75 K 150VN
E SERIES HIGH HT R834 75K HI RES
E SERIES HOTEL MODE 1. PRESS AND RELEASE A VOLUME BUTTON 2. WHILE GRAPH DISPLAYED,PRESS THE MUTE BUTTON ON R/C
E SERIES LOSS OF VIDEO POSSIBLY INTERMITTANT / XL301,R308,IC302
E SERIES NO PIC - HEATERS LOW OR OUT R940 4R7 磕 FUSIBLE HI RES - ALSO R901 22R 磕 FUSIBLE IN A1 CCT
E SERIES PIC LO WIDTH - 150V VARYING C822(MAY IN VALUE WHEN WARM)
E SERIES SERVICE MODE1 -REMOVE SK702 LINK(ON LHS OF MICRO IC701) & USE VOL +&- TO SELECT & BRIGHTNES +&- TO ADJUST
E SERIES SERVICE MODE2 00 SOURCE SELECT DO NOT ADJUST,01 90 SYSTEM OPTIONS RESET TO D0,02 20 HUE NOT USED DO NOT ADJUST
E SERIES SERVICE MODE3 03 0E HOR SHIFT MUST BE LESS THAN 40,05 36 E.W.PAR LESS THAN 40,06 2D E.W. CORNER LESS THAN 40
E SERIES SERVICE MODE4 07 14 E.W. TRAPEZ LESS THAN 40,08 20 VERT SLOPE LESS THAN 40,09 16 VERT AMP LESS THAN 40
E SERIES SERVICE MODE5 0A 5C VERT "S" COR MUST BE RESET BETWEEN 80&BF,0B 1B VERT SHIFT LESS THAN 40
E SERIES SERVICE MODE6 0C 2A RED DRIVE LESS THAN 40,0D 2A GREEN DRIVE LESS THAN 40,0E AA BLUE DRIVE BETWEEN 80&BF
E SERIES SERVICE MODE7 0F 57 PEAKING RESET TO 1A,10 5F BRIGHTNESS BETWEEN 40&7F
E SERIES SERVICE MODE8 11 A0 SATURATION BETWEEN 80&BF,12 1F CONTRAST LESS THAN 40,13 03 AGC LESS THAN 40
E SERIES SERVICE MODE9 STORE SETTINGS WITH SOUND MUTE BUTTON
E SERIES STBY ONLY - NO LINE DRIVE 150V HT & LT PRESENT - LINE DR TFMR T401 SEC - WAS ABLE TO REPAIR
E SERVICE MODE REMOVE SK702 LINK(ON LHS OFMICRO IC701)STORE MUTE BUTTON
E STBY NO LINE DRIVE LINE DRVTX T401
F SERIES
F 1 FLASH=TDA884? ERRORS
F 2 FLASH= OVERVOLTS/XRAY ERR
F 3 FLASH=LINE STARTUP SEQUENCE FAILED
F 4 FLASH= BEAM LIMITER LOOP UNSTABLE
F 5 FLASH=VERT SCAN ERR
F 6 FLASH=TDA884? RESET STUCK
F D20TFG5 STBY LED FLASHES 4 TIMES R417(1K)C411(0U56F250V)
F INT NO PIC,(I403 5V REG)
F NO SIGNALS I403(5V REG)
F PIC 8 SECS THEN OFF LED 4 FLASHES REPEATS BEAM CURRENT ERR
F SERIES HAVE SERVICE MANUAL
F SERIES NO SIGNALS WHEN AERIAL LEAD FLEXED RESOLDER DRY JOINTS ON 5 VOLT REGULATOR(I403)
F SERIES STBY WITH LED GIVING 4 FLASHES AFT 20 SECS R909,R913 & R922 180K,D910/901 ON CRT BASE
F SERVICE MODE LINK ACROSS P701 PINS 2/3
F STBY LED 4 FLASHES R909,R913 R922 180K ON CRT PANEL. F DEAD Q801(IRF1830G)Q404 Q403(2SD468C),D801,D805(130V),I402,C412,R814 0R39,R816,R802 R812
F WARM 4FLASHES BEAM CURRENT ERR
F WARM STBY FLASH,D901(7V5 ZD),D910(5VZD) BEAM LIMITER ON CRT BASE PANEL
F WARM STBY FLASH,R909(180K),R913(180K),R922(180K) ON CRT BASE PCB
G INT COLORS ADD 2X 8P2F50V FROM PINS OFCRYSTAL X501 TO THE GROUND END OFC515
G SERIES DEAD TRIPPING,LOPTR,SCAN COIL PLUG
G SERIES INT COLOR PLAYING TAPES ADD 2X 8.2 PF 50V CAPS FROM PINS OF CRYSTAL X501 TO THE GROUND END OF C515
GRANADA C22CD4 =TX1409 WIZARD(LOPTX 471074 00)
MK3 SND - LOW & DISTORTED. OR71(820)
MK3 SND DISTORTED. OR71(820)
MK3 SND LOW/DIST OR71(820)
MODEL NO'S 1ST DIGIT: 9 = TXT; 8 = NON TXT 2ND DIGIT. = CHASSIS I.E. 9 = 190 E.G. DN8951 = 190 NON TXT
MODEL NO'S 1ST NO. 9 = TXT; 8 = NON TXT 2ND NO. = I.E. 9 = 190 E.G. DN8951 = 190 NON TXT
MODEL NO'S NEWER MODELS GO BY LETTER E.G. VU2CEO = C SERIES
PT92 LOPTX OREGA 40348A-09 10669900 C P5 PT92 110 DEGREE
PT92 SEE WHARFDALE,NAIKO,DECCA,BUSH,AKURA,JMB
PT92 SERVICE MODE,REMOTE TEXT TIMER,SUB/PAGE BUTTON AND VOL DOWN ON TV
PT92 TUNING HOLD REMOTE ON.OFF(ON PHILIPS REMOTE) FOR 5 SECS THEN AGAIN
PT9255 120/125
PT9255 120/125 CHASSIS
PV9352 130
PV9352 130 CHASSIS
PZ9354 130
PZ9354 130 CHASSIS
T28N SEE TATUNG
TATUNG UK(LTD) SERVICE DIVISION STAFFORD PARK 10 TELFORD SHROPSHIRE
TOPTEL CODES 156/116/118/124B/081/067/ 01952 290 111
TU2C52 SEE C SERIES
VU2CEO SEE C SERIES
WS6674 PT92 GOTO PT92
GOTO TOP If you know of any fault repairs NOT here. Please email the info to me
your fault NOT here , try my step by step guide Do it yourself guide
Highlandelectrix